Search results

  1. S

    Transmission Help. Another 1 1/2 to go.

    I have the Clutch installed and Im installing the Transmission. Ive spend 2 Hours trying to get it to go the last inch and half. Ive turned the engine around a couple of times. Im doing this myself. Should I have a helper turner the engine while I push the tranny forward towards the...
  2. S

    Insurance table

    http://www.condonskelly.com. 2500 mile limit, 0 deductible, $100 towing 300k liability. $18K Value. $166 a year.
  3. S

    Installing a new Clutch. What should be

    Thanks for the Research on the Torque settings Steve
  4. S

    Installing a new Clutch. What should be

    Thanks Ive not received the bolts yet but I do remember that when I used ARP head bolts. I had to oil the threads and passages to get the correct torque and there specs were alot different than the manual. Thanks Steve
  5. S

    Installing a new Clutch. What should be

    Thanks for the Education on on Clutch Bolts. I hate to ask, My Chilton Manual says Torque 12 to 20 Pounds on the Pressure Plate Bolts. I was going to use 20 Pounds. Is this not Enough? Thanks Steve
  6. S

    Installing a new Clutch. What should be

    They Did have lock washers. When I torqued my new pressure plate with the Mr Gasket bolts the washer were slightley loose. I also noticed on the old pressure plate alot of scratching where the the bolts bolted to flywheel like the pressure plate had moved or shifted on the flywheel.
  7. S

    9" rear ends & gt40 heads!!!!

    All I know is I haven't laughed this hard at work before. Thanks for the Humor
  8. S

    Installing a new Clutch. What should be

    You guys Scared me with the Hardware Store Grade 8 Bolts. I ordered some ARP bolts this morning. Now Ill have to pull the clutch off and try again. After looking at the clutch and the bolts I beleive I figured out my Clutch Judder when taking starting off. The Pressure Plate Bolts Were...
  9. S

    Installing a new Clutch. What should be

    Thanks for the input I went with the Hardware Grade 8 bolts and washers. Hope it holds together. Steve69
  10. S

    Installing a new Clutch. What should be

    ANYONE ON THE INPUT SPLINE THANKS
  11. S

    Power Brake Problem

    I converted to a 5.0 booster and mine does the same thing. The brakes work great. Ive seen previous posts and that seems to be common to make that noise when you hit the pedal. You could call up where you bought your brake kit and ask them but I think everything is ok. Steve69
  12. S

    Installing a new Clutch. What should be

    Wheel Bearing Grease? How much play should there be at the input shaft? seems to move around a bit. Thanks
  13. S

    I'm doing an EFI conversion, have a few ?'s

    That looks great. What did you polish the manifolds with? I would by a battery relocation kit. It will have all the cables to do the job right. I beleive with the swap you still need your starter solinoid. Steve
  14. S

    Installing a new Clutch. What should be

    Greased? I have some Lithium Grease and should I put any on the the input shaft where the clutch disc rides. On the shaft that the throwout bearing rides? Thanks
  15. S

    MUSTANG STEVE'S BUSHINGS

    I haven't used them but you also by Granada Tie Rod ends that are like $15.00 for a set.
  16. S

    17x9 rims fit all the way around 69 Mustang

    Will 17x9 rims fit all the way around on 69 Mustang. What size tires would look the best. Thanks
  17. S

    How do I add a picture to my signature

    None Taken Have a good weekend
  18. S

    How do I add a picture to my signature

    Thanks for the Help I think I finally figured it out. Steve69
View older results
Top Bottom
Back
Forums
Menu