Search results

  1. S

    What is the proper Voltage output?

    Correction********Voltage gauge************* not regulator
  2. S

    What is the proper Voltage output?

    Thanks for the info. One more Question. Where should I wire the voltage regulator to get the best reading of voltage. Thanks Steve
  3. S

    Lighting/Wiring Question

    Thanks for the help It looks like I have a couple of options. Steve
  4. S

    Lighting/Wiring Question

    **********Anybody Else********** Thanks
  5. S

    What is the proper Voltage output?

    Just finished up 3G Taurus Alternator intall. When I fired it up my new Votage Gauge in the Car Said 13 Volts. I checked the output at the battery and its at 14.65 Which seems a little high to me. It works really good without any noise. Thanks
  6. S

    Lighting/Wiring Question

    Hi Guys I have a 69 Mustang and the interior lighting isn't the greatest because there is no dome light. It has the rear quater lights and the under dash lights. I bought a Rearview mirror off Ebay that is a Newer Cobra mirror with combination map light & dome light. It has 3 Wires...
  7. S

    Found a nice 3G alternator at the Yard

    It was off a 93 taurus 3.8.
  8. S

    Found a nice 3G alternator at the Yard

    Any problems with painting it? I was worried that the paint might go in the openings and screw something up inside. Dont really want to take it all apart to paint it. Thanks for the info
  9. S

    Going To the Junk Yard tommorow.

    I was talking about the 3G conversion with the lower bracket. I have no idea about the Taurus Fan. The summit price of $60.00 doesn't sound to bad either.
  10. S

    Got out bid

    My Wife thinks Im crazy for also bidding at the last 30 seconds. I told her thats why you never win anything!
  11. S

    One wire Alternator and working Volt meter

    What is the Fuse link from the fuse box.
  12. S

    Going To the Junk Yard tommorow.

    I Beleive you have to extend the lower adjuster bracket a little bit longer. I know of a few people that have done it.
  13. S

    Going To the Junk Yard tommorow.

    So you tried to install it on the Engine side of the Radiator? Ill have to do some measuring before tommorow. Thanks
  14. S

    Going To the Junk Yard tommorow.

    Im looking for a 3G alternator. They say they have some from Taurus's. My question is Radiator Electric Fans. I did a search and I couldn't fine one on the Junk Yard Fans. What Year and Model should I be looking for a good doner for a 69 Mustang. Mounting hardware? should I be...
  15. S

    Anyone use this EFI Conversion Harness?

    That seem like a really good price. Let us know what you think of it If you purchase the harness. What I would want to know if its a total plug in harness. Do you have to covert anything over. Let us know what happens Steve
  16. S

    Equalizer Bar Question.

    Im using a equalizer bar with rods. on a Ford 302 bellhousing. Its a 4spd transmission. Ive also replaced all the springs with new also. Thanks
  17. S

    Equalizer Bar Question.

    Ive Replaced the Equalizer Bar, Bushings and the clutch pedal rod that goes the the Equalizer Bar. It just doesnt seem to move very smooth. The Clutch pedal rod doesn't seems to be very tight. Will the Equalizer bar Bracket adjust for this problem. The clutch pedal seems to stick half...
  18. S

    Transmission Help. Another 1 1/2 to go.

    I got it in Had to pull it out a little and my Dad pushed in the clutch pedal. Thanks again. Steve
  19. S

    Transmission Help. Another 1 1/2 to go.

    Gal Friend Went Shopping. Worked on it the last hour and got it to 1/4 to 3/8 of inch from the bellhousing. Put the drive shaft on the end and spun it and it slipped in to that point. I spent another 30 minutes trying to get it to go the rest of the way. Is is same to say its enter...
  20. S

    Transmission Help. Another 1 1/2 to go.

    I did test the new Clutch disc to make sure it fit. It slide on, but it was fairly tight fit. It did slide on the input shaft once it was on. I did use a alignement tool ot get it centered when I had bolted the pressure plate on. I dont have my shifter on. Does it matter which lever I...
Top Bottom
Back
Forums
Menu