Search results

  1. B

    1964 1/2 Mustang Starter Solenoid

    I just did a efi swap on my 1964 1/2 Mustang and when it was time for me to start the car the starter solenoid started smoking and i guess eventually went out. Now when I try to start the car it is just a clicking noise. I am going to take the starter off and get it tested and I just ordered...
  2. B

    12 volt source in start & crank position

    I am doing a efi swap in my 1964 1/2 Mustang and I am having problems with finding a source that gives 12 volts in both the start and crank position.I was trying to use a ignition wire that was hooked up to a stereo but in the crank position it loses voltage. Would I maybe have to tap into the...
  3. B

    0 compression

    so the valve lash is controlled by the rockers and how tight they are right? i am running a f303 cam, 1.6 ratio crane cam rockers and i am running stud mount. I am also running stock length hardened pushrods. with M-6049-X306 heads
  4. B

    0 compression

    I have zero compression on my motor right now. What are the top things that i need to check? Oh by the way someone did some motor work on the car such as cam, new rockers and pushrods. Could it be because the pushrods are not long enough or too long? or maybe rockers are down too tight?
  5. B

    Not getting 12volts from ignition switch

    Right now i am having a problem in my 1964 1/2 mustang. I am doing a efi swap and i have a harness that i installed. Right now when i try to crank the car there is not 12 volts goin to the ignition wire i used when the key is in crank position. What could the problem be? Does anyone know what...
  6. B

    Car not starting

    The mass air meter that i have is part # F4SF-12B579-AA AFH70-02A 4D26
  7. B

    Car not starting

    Ok well the computer i have is a A9L and the mass air meter that i have is 70mm motorcraft and not a aftermarket. So since these things match up with what you are saying that means the problem has to be from somewhere else right?
  8. B

    Car not starting

    ok so this might be my problem then right? because i just did the efi swap into my 1964 1/2 mustang. I bought the computer i am using off ebay from someone and i also bought the 70mm mass air meter that i am using off ebay from someone else. So do i need to go to a shop that tunes and have them...
  9. B

    Car not starting

    I am trying to figure out why my car is not starting up, it acts like it is trying to fire up but does not. If i have a mass air meter that is calibrated for 19lb injectors and i am running 24lb injectors will this cause the car not to fire up?
  10. B

    Msd Distributor install help needed

    I just installed a new msd distributor and my timing is all off, the car will not start. Does anyone know how to tell which spot is spot#1 on the msd cap and how to make sure the motor is at tdc?
  11. B

    How to set the timing

    thanks
  12. B

    How to set the timing

    I just put a f303 cam and aluminum heads on my 92 5.0 motor. Msd distributer and Msd 6al box. Can someone give me detailed instructions on how to set my timing? and also how long do you think i can ride without a tune?
  13. B

    Installing upper and lower intake

    n also what is fpr? and as far as the hoses i can get those from kragens or something?
  14. B

    Installing upper and lower intake

    ok, so i dont have to put the tree piece into the intake? or how should i cap it off?
  15. B

    Installing upper and lower intake

    Ok I have a 1991 5.0 block that I had built up, But I am left to install the upper intake. I have the upper intake and I have the tree looking thing that goes under it. Now i am comfused with what I connect to what. The lower intake is on the block and I know there is a whole in the back of the...
  16. B

    Stock Valve Covers

    thanks, i guess imma just have to do some testing with the stock before i try these ford racing valve covers i bought so if the stocks work i can return the ford racing ones
  17. B

    How much RWHP?

    Floo Tek 5.0 X heads, they are made just like the GT40 heads
  18. B

    How much RWHP?

    How much rwhp do you think a Mustang would put down with these parts? 1991 5.0 HO motor f303 cam new ford racing lifters 1.6 ratio crane rockers typhoon upper and lower intake aluminum heads 180cc/58cc msd distributer 24lb injectors 70mm mass air meter 70mm throttle body long...
  19. B

    Stock Valve Covers

    Will 1.6 ratio rockers clear inside stock valve covers?
  20. B

    push-rod length????

    I am runnin aluminum heads with a f303 cam and 1.6 ratio rockers. I know i need hardened push-rods, but what length will i need? stock or the next length up which is something like 50,000th of a inch?
Top Bottom
Back
Forums
Menu