Search results

  1. kcobra302

    show off your .................. gauges

    i wanted to have something with a little more accuracy than the stock guages. i went with easy removal in case i want to go back to stock. probably would take less than an hour to remove them all. fuel guage is just visible under the cover and it mounted in the cowl. inside the car: clock...
  2. kcobra302

    in need of a Mustang 78 king cobra

    where are you located? i am in the process of replacing the the pilot bearing in my king, so the tranny is out of it but if you are close enough you can come take a look to see if it is of interest to you.
  3. kcobra302

    Mustang II Marti Reports

    response to my email request: Kcobra302, We have received your email regarding reports for Mustang IIs. If you visit this link, http://martiauto.com/report-dlx.htm, you can see what we can offer now for the Mustang II. We have been licensed by Ford Motor Company with the entire production...
  4. kcobra302

    94-95 t5 install experience

    installed 94-95 t-5 with the m2 bell last summer and put roughly 750 miles on the setup. i noticed a slight leak over the winter and it turns out the bearing retainer was leaking a little. however, i did find a much bigger issue with the wear on the input shaft. you could clearly see a wear...
  5. kcobra302

    hurst shifter

    didn't know they still made these http://performance.drivewire.com/interioraccessories/fordmustangiigearshiftlever.html
  6. kcobra302

    lowering the II rearend

    thanks guys. the blocks sound like an easy "fix" but i have talked with people that have used them without incident. i am going to go with the springs
  7. kcobra302

    lowering the II rearend

    just before the big server crash, there was a thread running about lowering the rear of a II. i don't recall there being any one agreed upon scenerio. i am looking for opinions on how to properly drop the rear 1" to 2". suspension travel and pinion angle will be taken into consideration and...
  8. kcobra302

    2005 Cobra II?? You bet!!

    sal, car looks great. nice choice with the twin screw. will you be doing a limited run of the cars? stangnet guys did a great job on the article.
  9. kcobra302

    new v-8 mount source - $100

    http://www.mustangii.net/forums/topic.asp?TOPIC_ID=3139
  10. kcobra302

    slip yoke travel

    not trying to beat a dead horse but i am right in the middle of the t-5 swap and the last major hurdle is the driveshaft. i have read the threads here and on another site pertaining to the swap and drive shaft lengths. the measurements i have taken on my car and driveshaft vary by as much as...
  11. kcobra302

    if you need them....here they are

    http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&category=50454&item=7968960865&rd=1 put a little dent in your wallet. theres got to be another way.
  12. kcobra302

    JL CobraII white-green stripes

    somebody was looking for one of these several months ago. there is on up on ebay. http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&category=50434&item=7944946369&rd=1
  13. kcobra302

    I think I want to cry

    thanks for the quick turnaround. i wll call them tomorrow and let you guys know what i come up with. hopefully its better than the last call i made.
  14. kcobra302

    I think I want to cry

    hey sleeper, can you get a scan of that page with the heidts ad? i have not been able to find mustang and fords in this area. i want to try to call them again this week or the beginning of next.
  15. kcobra302

    u-joints

    i was given a set without the grease zerks. i took them up to a local parts store and had them run the numbers for me. the numbers match up to a mustang II v-8 4 speed but the caps are very different than whats on the car. the u-joints currently on the car have caps that are all the same...
  16. kcobra302

    u-joints

    looking for recommendations for a heavy duty driveshaft ujoints. i do not want the type that have a grease fitting. brand name and/or a part number would be apreciated. thanks
  17. kcobra302

    happy holidays

    wanted to wish everybody a happy and safe holiday weekend. yes, even glenn. :cheers:
  18. kcobra302

    I think I want to cry

    I talked with 2 gentlemen there. the first guy didn't really know what i was talking about and the second guy said the don't have stock replacements. man i wish they did, it would be a could time to put them in since tranny and headers are out of the car right now. i will try them again...
  19. kcobra302

    I think I want to cry

    bad news. just talked with the guys at heidts. the mounts are not for stock-replacement. they are a tubular style to put a chevy engine into thier style 1 mustang II rails.
  20. kcobra302

    Targa band removal

    yup, holes all along the roof in 2 rows. you need a trim tool to remove the 2 pieces of trim. you could use a flat screw driver but you need to be very careful. there are plastic push clips that hold the trim down, which in turn holds the targa band. there really isn't any re-enforcing along...
Top Bottom
Back
Forums
Menu