Search results

  1. 0

    Anyone use a Densecharger CAI with a C&L 80mm MAF?

    I was just wondering if this setup is possible and if anyone has tried it? Thanks,
  2. 0

    VERY slow air leak???? Can't figure out whats up with my tire. :-(

    Is it bad to use that fix a flat sealer stuff? Does it actually affect the characteristics of the tire or cause problems? Just curious? Thanks,
  3. 0

    VERY slow air leak???? Can't figure out whats up with my tire. :-(

    I just had a nail removed from my right rear tire... when I brought it home the bastards filled it to 45PSI? I don't know if it was to help with the fix they did or what. I do notice that it still has a extremely small slow leak out of the spot they fixed. I put some soap on it and it has a...
  4. 0

    Does your stang do this?...GOD!

    I have the same issue with my 01 cobra.... after driving for awhile there is a low pitch howl at cruising speed. It isn't really loud. However, when you let off the gas it goes away... if you give it some gas it goes away... It is only when you are cruising and at a constant RPM... mostly...
  5. 0

    Tire side wall strength for cornering, what is good?

    I have a Hypertech programmer that will take care of that.
  6. 0

    Tire side wall strength for cornering, what is good?

    Well it would be better than using 255x45 correct? As far as sidewall strength? Thanks,
  7. 0

    Tire side wall strength for cornering, what is good?

    I was thinking of going 255/40 all the way around with BFG's and was curious if going lower is going to make the strength of the sidewall less? Oh they will be on stock rims 17x8. Thanks,
  8. 0

    Tire side wall strength for cornering, what is good?

    So my question is if you go higher like a 45-50 profile, is this better sidewall strength then say a 35-40 profile? I was just curious if going lower is better for strength and stability in the corners or is going higher better? Thanks,
  9. 0

    MM k-member brace?

    Stallion I ended up ordered one and figured it would help more than the 2 point oem brace. It was only $99 so I figured what the hell. I imagine installation is real easy. It just goes into the existing holes correct? Thanks,
  10. 0

    MM k-member brace?

    Has anyone used one of MM's K-member brace's? I was just curious if it helps, and if you can notice a difference? Or is it a waste of money? I have there strut tower brace on now, but was wondering about the lower end. There is just a weak looking bar on there now, and figured MM's 4 point...
  11. 0

    I have a low humming noise when cruising below 2200rpm

    I have a low humming noise when cruising below 2200rpm it isn't loud and it only seems to happen in 3,4,5 gear... when you step on the accelerator it goes away. It sounds like it is coming from the rear end. It has plenty of fluid as I checked that. Does anyone have any ideas??? Thanks,
  12. 0

    Has anyone been to American Alignment in Kent, WA??

    Has anyone been to American Alignment in Kent, WA I was just curious if they do good work? I have been trying to find a good alignment shop that will work with altered suspension (lowering springs caster camber plates) and know what they are doing. Thanks,
  13. 0

    Opinions on alignment setup

    What do you have setup for the following... Camber Caster Toe I am thinking of going... Camber -.5 Caster +4.5 Toe in .5 Thanks,
  14. 0

    Taking the cobra in for alignment after suspension upgrade. Check out these settings.

    Well I am done installing my eibach prokit and bilstein shocks/struts front and rear. Along with maximum motorsports CC plates, strut tower brace, and subframes. The ride quality is awesome and the car grips really good... It does pull to the left a little. I am taking it in for a alignment...
  15. 0

    Car Pulls a little to the left. Camber Question??

    So my car pulls slightly to the left. So my question is... if it pulls to the left which tire do I need to adjust the camber on? The right one? If so would that mean I would need to add more positive camber or negitive camber? I am planning on taking it in for a alignment this week. but I...
  16. 0

    Fluid level in rear gears

    I have no whine in my gears. When I filled it up the car was angled and not flat. (The rear of the car was jacked up) So I am wondering if I have to much in. Was just curious if it can cause problems.
  17. 0

    Fluid level in rear gears

    What happens if the level of fluid is more than the edge of the fill hole for the rear end? Was just curious what this can do? Do you get whine? Thanks,
  18. 0

    Bilstein Strut Nut what is the trick?

    What is the trick to get the nut tight on the top of the Bilstein strut... the shaft keeps spining. Did you all have any tips for this??? Thanks,
  19. 0

    Front QA1 Struts blew... What do you think of the Bilsteins?

    What is the difference between the HD and the SP's? I ordered the HD's with my eibach prokit. Is the SP a softer system? I believe the HD is for heavy duty, but I maybe wrong?
  20. 0

    Front QA1 Struts blew... What do you think of the Bilsteins?

    The only problem is they don't make the illuminas for the 01 cobra with IRS... That is why I decided on the Bilstiens. I tell you what... I can't believe that the Bilsteins are as harsh as the QA1 strut. I think QA1 should of said (racing strut only) Not a factory replacement. Those thing ride...
Top Bottom
Back
Forums
Menu