1996

  1. M

    Doors from 2000 feel lighter than 1996

    When I was at the wrecker pulling my 'new' s197 seats, I noticed the doors on a close by 2000 really felt lighter than my doors (1996). My questions are; One. Are there weight differences? Two. Will 2000 bolt on a '96? Three. Were they made of different steel? maybe aluminium? Thank you
  2. ogvenom

    Lots of vibration after changing u joints in driveshaft

    1996 Mustang Cobra SVT 5 speed manual, all stock except 4:10 gears, bassani x pipe and flowmaster mufflers on Eibach lowering springs. I removed my driveshaft, took it to a local driveshaft shop and they replaced the u-joints and re-balanced the driveshaft. I put it back on and now I have...
  3. P

    What did i get myself into

    Ok guys im kind of worried that I may have dug myself into a pretty deep hole. I recently purchased a 1996 Cobra with 100k(ish?) for a good price I would say (the odometer is stuck at 100631, but judging by interior it doesnt look far off). I am learning stick on this car as well. It seems I...
  4. 9

    For Sale For Sale - 1996 Mystic - #1985/2000

    Up for sale is my 1996 Mystic Cobra. It is build #1985 out of 2000. I have all documentation that it is a mystic, including letters from Ford and SVT verifying. I also have the original window sticker as well. (A copy of the window sticker is shown but I have the actual one framed). Location...
  5. rx79gez8gundam

    1996-1998 4.6L SOHC Engine Harness Connector C210 Pinout

    I spent several hours searching without luck for the 42-pin C210 engine harness pinout without luck. Since I ultimately had to trace each wire by hand I decided I would document my work for future reference and post it if anyone else needs it. I have a new edge harness I will also trace when I...
  6. D

    SOLD [FOR SALE] 1996 Mustang GT Convertible / 4.6 - Automatic /Former Virginia car

    1996 Mustang GT Convertible / 4.6 - Automatic /Former Virginia Car, 112,000 miles Car has NO Rot or Rust, Runs excellent, have 2 sets of wheels/tires (all new) for the right price Asking $6500.00 or Best Offer, **** Make an Offer****** Attleboro, MA 508-269-2072
  7. C

    96 pats help

    Hello Stangfam, I have a 1996 cobra. Running and functioning perfectly fine. My pats transceiver (black plastic ring with wire running under driver side dash and connects via a white plastic head ) broke near the black plastic ring part that goes onto ignition cylinder. Now the theft light...
  8. M

    Help Removing 1996 Cobra Master Cylinder

    I need some guidance on removing the lower nut securing the master cylinder to the hydroboost. I have searched online but found nothing. The space is so small and I can barely get a hand between the valvecover and master cylinder using the smallest socket wrench I have. I've also tried to go...
  9. E

    Gt And V6 Transmissions

    My friend has a 1996 Mustang GT that he wants to LS swap (he's a sinner) later this summer, and I want to do a V8 swap in my car which is a 1998 Mustang V6. He said he'd sell it to me for $850, but I was wondering if I also needed to buy his transmission from him or if the two cars use the same...
  10. T

    Engine Swap 1996-2004 Need Advice

    I have a 1996 mustang Gt that has a bad motor in it, I am going to be swapping it out with a low mileage complete engine from a 2004 both being romeo engines, I want to use as many of the new engine parts as possible with that being said what I am i looking at here? is my fuel system and wiring...
  11. chapters707

    Should I Replace Manifold Before Dropping My Engine?

    Hi all, I am getting ready to swap out my busted 96 4.6 sohc engine with an identical one in the next week or so. (Been struggling with a stubborn midpipe bolt.) Anyway I've been reading today about a common problem with these plastic manifolds leaking coolant and eventually cracking. This new...
  12. J

    Electrical 1996 Mustang Convertible Auto Power Window Drop- Please Help!

    Hi. Newbie here. First post. Bought a 1996 mustang GT Convertible. 167,000 miles. Runs good. When I open the doors, the windows are supposed to drop a 1/2" to clear the top right? Mine don't. Went and read all kinds of posts that said how to reinitialize the smart window motors. Tried...