• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

02 Readings Again

  • Thread starter Thread starter dcurtis
  • Start date Start date Oct 19, 2007

dcurtis

10 Year Member
Jan 19, 2006
688
7
39
Oct 19, 2007
#1
  • Oct 19, 2007
  • #1
I let my car cool off completely so I could retest the voltage at the comp to the 02's and I got
Left_____Right
.6v______.2v
.68______.3
.7 _______.37
.71______.4
.71______.42
.72______.44
.73______.46
.73______.47
.76______.52
.75______.51
It basically stays at about .65v left and .3 at idle, the .76___.52 is when I gave it some gas for a second and then it went back down to about .65 and .3, what do the voltages mean?

The voltage slowly raised to the .6___.2v which is where I started keeping track of it, it took about 2 or 3 minutes to get there. When I let it sit after gassing it it slowly went back down to the original readings of about .65 and .3
The right 02 will only register in milli volts for the first minute to 2 minutes or so also
Thanks for your help
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Oct 19, 2007
#2
  • Oct 19, 2007
  • #2
Your meter might be averaging the readings or have a low internal impedance or something weird like that.

The readings should obviously toggle between 0.1 and 0.9 volts atleast once a second. They don't read a static voltage - if they do either your DMM is causing the issue or both O2's have issues.

You might want to check the HEGO ground since you're not waiting a super long time before testing. With properly functioning HEGOs, they light off within a minute in my experience, and can take as long as two minutes.

Good luck.
 

dcurtis

10 Year Member
Jan 19, 2006
688
7
39
Oct 20, 2007
#3
  • Oct 20, 2007
  • #3
What exactly do you mean when you say, The readings should obviously toggle between 0.1 and 0.9 volts atleast once a second? and, With properly functioning HEGOs, they light off within a minute in my experience, and can take as long as two minutes. And last, how and where do I check the HEGO ground?
The right 02 was replaced Wednesday, and I don't know how old the left is but I will pick up that next week so they will both be new.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Oct 20, 2007
#4
  • Oct 20, 2007
  • #4
What exactly do you mean when you say, The readings should obviously toggle between 0.1 and 0.9 volts atleast once a second?
Click to expand...

When your meter is on the O2 signal wire, your reading will vary (or it should). Here's an example of how mine might read:

0.20, 0.92, 0.14, 0.85, 0.23, 0.72. That would all be seen on my meter in about a 5 second period.

The way the puter works is to correct and overcorrect constantly. It would be like teaching a kid to bowl. You put two 2 x 4's on the bowling lane, one foot from the center of the lane. No matter how the kid throws the ball down the lane, it will bounce off the 2 x 4's and end up in the middle of the lane by the time it reaches the pins. Same kinda deal with the narrowband O2s.


and, With properly functioning HEGOs, they light off within a minute in my experience, and can take as long as two minutes. And last, how and where do I check the HEGO ground?
Click to expand...

O2's dont start providing useful info until they reach about 600*F. When you start the engine, it takes them 30-120 seconds to reach this temp (light off) and become useful. If you start your cold car and immedately take a reading, it can suffer from great hysteresis (it will be nearly a constant value). The heating circuit on the O2 is what makes it light off so quick (older O2s, called EGOs, were not heated and could take over 5 minutes to light off). If your heater circuit is not working and you're doing your testing relatively quickly after starting the car, that could be an issue.

Good luck.
 

dcurtis

10 Year Member
Jan 19, 2006
688
7
39
Oct 20, 2007
#5
  • Oct 20, 2007
  • #5
I got it now. Thanks
 
You must log in or register to reply here.

Similar threads

E
2007 GT Stalls when lights or a/c turned on
  • ejscarfo
  • Jun 22, 2026
  • 2005 - 2009 Specific Tech
Replies
3
Views
369
2005 - 2009 Specific Tech Sep 26, 2026
manicmechanic007
K
Engine 2000 Mustang GT - Fuel issue post-blown spark plug repair
  • kenster1092
  • Feb 26, 2026
  • SN95 4.6L Mustang Tech
Replies
4
Views
601
SN95 4.6L Mustang Tech Mar 10, 2026
kenster1092
K
Engine Random Misfire at idle.
  • Gulftown980x
  • Jul 29, 2026
  • SN95 4.6L Mustang Tech
Replies
11
Views
619
SN95 4.6L Mustang Tech Jul 31, 2026
squeak93
0
V6 to V8 Swap info
  • 02_2v_Curtis
  • Jan 11, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
2
Views
1K
1996 - 2004 SN95 Mustang -General/Talk- Oct 7, 2026
2v_johnny
2
J
Thanks for the information on codes 31,34,44 and 94!
  • JK86LX50
  • Mar 5, 2025
  • The Welcome Wagon
Replies
3
Views
378
The Welcome Wagon Aug 5, 2025
gkomo
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?