• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Electrical 1993 LX 5.0 runs for only 30 seconds at a time before dying.

  • Thread starter Thread starter mrjfox93
  • Start date Start date Dec 3, 2019
M

mrjfox93

New Member
Dec 3, 2019
1
0
1
Cedar Park Tx
Dec 3, 2019
#1
  • Dec 3, 2019
  • #1
Hi y'all im new to this so hopefully I'm posting in the right place!
Since July my 5.0 hasn't been able to stay running. One day it was running fine and the next it would run rough and die within 30 seconds. At that point we replaced the fuel pump and the fuel filter. It ran for 20 minutes then started doing the same thing. Since then we have replaced the coil ,TFI module, wires to tfi, pick up, ignition switch and the distributor rotor and cap. At this point we figured it was the computer that went bad so we sent it off and they replaced the capacitors. Now it has an intermittent spark and it still can't stay running. The last things we replaced were the fuel pump relay and the computer relay under the dash. We sent the computer off again to make sure there wasn't anything wrong with it and they said it was still good so we're waiting for that to come back to do some more tests. Not sure what's wrong with it at this point, I'm just hoping someone could get us pointed in the right direction. Thanks!
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Dec 5, 2019
#2
  • Dec 5, 2019
  • #2
Why haven't you dumped the computer codes? Throwing parts, time, and money at a problem isn't the best way to fix things.
Test, observe, and then diagnose. The link below will get you started...

Dump codes sticky

Look at the top of the 5.0 Tech forum where the sticky threads are posted. One of them is how to dump the computer codes. Codes may be present even if the CEL (Check Engine Light) isn’t on. You don’t need a code reader or scanner – all you need is a paper clip, or if your lady friend has a hair pin, that will do the job.
I highly suggest that you read it and follow the instructions to dump the codes. http://www.stangnet.com/mustang-forums/threads/how-to-pull-codes-from-eec4.889006/
 
You must log in or register to reply here.

Similar threads

W
1993 LX 5.0 dies after ignition parts replacement
  • Warhorse85
  • Aug 16, 2025
  • Fox 5.0 Mustang Tech
  • 5 6 7
Replies
122
Views
3K
Fox 5.0 Mustang Tech Nov 4, 2025
General karthief
A
1987 5.0 speed density Foxbody crank no start
  • Alan2204
  • May 23, 2026
  • Fox 5.0 Mustang Tech
Replies
10
Views
315
Fox 5.0 Mustang Tech May 30, 2026
Mcmahst
S
Fuel ‘88 GT Runs Rich Cold — Fixes Itself When I Unplug Sensors (ECT, MAF, O2, etc.)
  • Sufarry
  • Nov 6, 2025
  • Fox 5.0 Mustang Tech
Replies
12
Views
881
Fox 5.0 Mustang Tech Nov 9, 2025
Mustang5L5
D
Fox 88 foxbody no power to red and black wire at fuel pump relay
  • drod88
  • Dec 1, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
346
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Dec 2, 2025
Mcmahst
W
  • Locked
Fox Wifes 1993 LX 5.0 dies after replacing ignition parts
  • Warhorse85
  • Aug 16, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
9
Views
319
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 17, 2025
Noobz347
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?