• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech

1994 Mustang Airbag Mistake 42

  • Thread starter Thread starter nobbel
  • Start date Start date Jun 19, 2013
N

nobbel

New Member
Jun 19, 2013
3
0
1
Jun 19, 2013
#1
  • Jun 19, 2013
  • #1
Hi,
I am living in the northern part of germany. I am the owner of a 1994 Mustang GT conv. with 5,0L engine. I have a problem and hope, anyone can help.
The airbag-lamp shows "42" = left airbag circuit open. I replaced both crash-sensors and the clockspring, but I failed. "42 is still alive. Then I checked the wirin from the crash-sensor connection (c148) to the end: red = ok, violet = ok, yellow/green = problem. I checked my "Ford Service Publication" CD (for 1995 Mustang) and found out: there should be a connector "C107" in the engine compartment and "C210" inside the car on the left side. OK, C210 was found but not C107. This time I cannot follow the wiring from C148 to the end because the car stands on a ramp, but I've seen two connectors under the left bumper near the firewall. I know, that I have to check all connectors and/or to replace a piece of the wiring, but which? from C148 to the firewall, or from the firewall outside to C210 inside or from C210 to the electronic-box? Can anybody tell me where that F*** C107 (or equal) is?
Greetings
Werner
 

toyman

10 Year Member
Jul 19, 2007
1,944
54
79
Vernon BC
Jun 19, 2013
#2
  • Jun 19, 2013
  • #2
C107 appears to be below the battery or in the inner fender in that area. However, try this. Disable the system by turning the ignition to off detach the negative cable from the battery and then the positive cable. Wait for at least 2 minutes. That will allow the module backup power supply to be depleted. To enable the system keep the ignition in the off position connect the positive cable then the negative cable. See if that removes the 42 code. I noticed that C210 is terminal 42. Not certain if that means anything though. This is all uncharted territory for me.
 
N

nobbel

New Member
Jun 19, 2013
3
0
1
Jun 20, 2013
#3
  • Jun 20, 2013
  • #3
Hi, I got it! It is a broken wire (yellow/green) at C107, located under the fender near the firewall. But, how can I pry out that little connector, because the wire is broken nearly 3mm before the plug?
Werner
 

Chythar

Recently finished repairing my rear
20+ Year Stangneter
Aug 26, 2004
2,373
140
113
Foothill Ranch, CA
Jun 20, 2013
#4
  • Jun 20, 2013
  • #4
I'm not sure about that specific connector, but many Ford connectors have a red piece of plastic in the middle of the connector. the plastic is either just pushed in there or has visible clips on the outside. With a bit of work, you can get the center piece out and get to the pins themselves.

If you can take some good closeup photos of the connector, I can probably give you better advice.
 
N

nobbel

New Member
Jun 19, 2013
3
0
1
Jun 20, 2013
#5
  • Jun 20, 2013
  • #5
Hi,
the connector must be taken out from the back. So I constructed a pin-out-tool, using the ink-reservoir of a ball-pen, but I can continue working only tomorrow due to rain and thunderstorm this afternoon.
Photos: how can I add them here?
 

toyman

10 Year Member
Jul 19, 2007
1,944
54
79
Vernon BC
Jun 20, 2013
#6
  • Jun 20, 2013
  • #6
Do you not see the "upload a file" button bottom right side next to "post reply"? Just follow the prompts.
 

5.0 Ford Guy

Founding Member
Nov 29, 1999
423
35
39
Brownsburg, Indiana
Jun 23, 2013
#7
  • Jun 23, 2013
  • #7
You can't upload pics if you just click "Post Reply" below. You need to click "More Options". That will have a place to upload files. Upload your pics there.
 

toyman

10 Year Member
Jul 19, 2007
1,944
54
79
Vernon BC
Jun 24, 2013
#8
  • Jun 24, 2013
  • #8
Well, on the screen I see between "Post Reply" and "More Options", is a button called "Upload a File". So if the picture is on your computer that's the button you want. With "More Options" will you may embed media from the following sites: Dailymotion; Facebook; Liveleak; Metacafe; Vimeo; YouTube and probably reference any URL as well. I thought the request was simply how to post a picture.
 

5.0 Ford Guy

Founding Member
Nov 29, 1999
423
35
39
Brownsburg, Indiana
Jun 24, 2013
#9
  • Jun 24, 2013
  • #9
Oh, I didn't see that. LOL. Wrong forum.
 
You must log in or register to reply here.

Similar threads

A
P0036 P0056 P0137 P0157 2020 Ford Mustang GT
  • AmkoA
  • Jun 16, 2026
  • 2024+ (S650) Mustang -General/Talk
Replies
0
Views
117
2024+ (S650) Mustang -General/Talk Jun 16, 2026
AmkoA
A
Electrical Ron Francis Headlight / Alternator Harness
  • dan50
  • Apr 30, 2026
  • Fox 5.0 Mustang Tech
Replies
0
Views
228
Fox 5.0 Mustang Tech Apr 30, 2026
dan50
D
Help--Need New Exhaust Gas Recirculation (EGR) Tube for 1994 V6 3.8 L Mustang--where can I find one?
  • DPP
  • Jun 5, 2025
  • 1994 - 1995 Specific Tech
Replies
4
Views
622
1994 - 1995 Specific Tech Jun 10, 2025
DPP
D
0
V6 to V8 Swap info
  • 02_2v_Curtis
  • Jan 11, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
0
Views
733
1996 - 2004 SN95 Mustang -General/Talk- Jan 11, 2026
02_2v_Curtis
0
M
01 mustang 3.8 fuel pressure issue
  • Mhaley2006
  • May 29, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
0
Views
162
1996 - 2004 SN95 Mustang -General/Talk- May 29, 2026
Mhaley2006
M
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?