• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

302 to 351W

  • Thread starter Thread starter Pinebluffracer
  • Start date Start date Jan 28, 2006
P

Pinebluffracer

New Member
Jan 25, 2006
33
0
0
Jan 28, 2006
#1
  • Jan 28, 2006
  • #1
I was thinking about going from my current 302 to a 351W. I have a bare 351W block and wanted to know if my stuff from the 302 will convert over? Will the 302 bell housing, heads, centerforce clutch 10.5, gt40 intake manifold, all the accessories up front, oil pan stuff like that convert? I have a feeling I will need new crank, rods, and pistons and that's ok; but if I have to change everything, I might as well rebuild the 302.
 

dastang2

Active Member
Dec 11, 2003
2,020
0
46
tx
Jan 28, 2006
#2
  • Jan 28, 2006
  • #2
you will need an oil pan,distributor,headers,crank pistons and rods,intake balancer,flywheel. i think that is all. you don't wanna use 302 heads on a 351 because that would be to restrictive. now i have some of those parts if you are interested. new. .040 hyper pistons,football rods, oil pan and pickup, crank. as well as a block. PM me or email me if you are interested. i have headers to but they are about to be gone. i hear you can use 302 shorties with modifications.
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Jan 28, 2006
#3
  • Jan 28, 2006
  • #3
Here are some notes I put together.

302 to 351W Swap In A Fox Body Mustang​
VRISTANG​

Note: This discussion focuses on EFI conversions as this is the most common route taken.

Engine Mounts-
Stock 5.0 mounts will bolt up to the 351w. Aftermarket alternatives include solid mounts and polyurethane mounts. Convertible Engine mounts are supposedly reinforced / stronger. Another alternative is lowering engine mounts from HP Motorsports. These are solid and lower the motor ¾”. Lowering engine mounts will reduce clearance between the oil pan and k-member. This presents clearance issues with some aftermarket pans and stock k-members, but should be ok for the FRPP pan.

Heads-
302 heads are the same as the 351w heads with the exception of the head bolt diameter. 302 heads have a 7/16” head bolt hole and the 351w has a ½” head bolt. Opening the holes can be done by hand or sent out to a machine shop.

Exhaust Headers-
Stock 302 headers will bolt up the head of a 351w (since the heads are basically the same), but will not mate up to the mid-pipe due to the extra width of the 351w. There are many aftermarket suppliers of 351w Fox Body headers including MAC, FRPP, Kooks, Hooker, and Hedman.

Intake Manifold-
Since the lifter valley of the taller 351w is wider than the 302, a new lower intake is required. Aftermarket suppliers of 351w intakes are numerous. Some 351w lowers will bolt up to standard 302 upper intakes, which can help reduce conversion costs. Be cautious with intake height if you are trying to clear a stock hood. Another option is to cut down the upper intake (This is easier on the plastic box upper from Comp Cams. This will cause clearance issues between the TB and valve cover if the upper is trimmed more than ¾”).

Oil Pan-
The 351w is wider so a new oil pan is required. The lowest cost option is probably the FRPP 351w pan for Fox Body applications. Aftermarket companies have standard volume, high volume, drag race , and road race pans available. A pan specific pickup tube and dipstick will also be necessary.

Oil pump-
The 351w oil pump is different from the 302 (mostly external). These are readily available in standard volume, high volume, and high pressure models.

Distributor-
The taller 351w does require a longer distributor. This can found from several stock Ford factory applications, mostly pickup trucks/vans. Some aftermarket suppliers do have electronic/TFI distributors available, such as MSD and Accel. Be sure that the cam drive gear is appropriate for your application. Roller cams require a steel dist. gear.

Engine Management-
Any stock 302 computer will handle a 351w. The EEC-IV will be fine until the combination gets more dramatic with larger injectors, heads, intake, and cam. Aftermarket plug in style chips are not going to offer ideal performance. The best solution is to invest in a chassis dyno tune or an EEC-IV computer tuning system.

Flywheel/Flexplate & Starter
The counter weight of the 5.0 is 50oz. The 351w counterweight is 28oz. You can reuse a 5.0 flywheel if you have it rebalanced at a machine shop. This is probably the easiest and most cost effective alternative. If purchasing new parts just make sure that the flywheel weight and starter tooth count are correct.

Harmonic Damper-
Again this must be matched to the counterweight of the 351w. Another consideration here is getting the crank pulley to line up with the rest of the serpentine belt system. FRPP does have a damper available specifically for this application.

Fuel Injector Rails-
The stock 302 rails will not be wide enough to fit the wider 351w lower intake. If the flex line in the front and rear of the stock rails is removed and replaced with longer sections of high pressure fuel line the stock rails will work just fine.

Fuel Injectors-
Proper injector size will depend on the application.

AC/PS-
This is the only stock 5.0 accessory bracket that requires modification. The stock AC pump and Power Steering pump will bolt up if a ford bracket is used. Without AC (PS only) the FRPP part number is M-8511-A351. For both AC and PS applications the FRPP number is M-8511-B351.

Emissions-
The crossover tube from a 302 can be used if it is cut and a section of high temp hose is used. The 302 air pump will bolt up correctly, and there should be no issues with the air injection system. The EGR should mount up properly, but this will vary with intake manifold selection. Routing of EGR hoses may need to be modified.

Hood-
The easy way to do it is get a taller cowl hood to replace the stock hood. This offers the aggressive look that many are looking for. If desired though, the 351w can clear the stock hood. Clearance will depend on engine mounts and intake manifold selection. If necessary some of the bracing on the underside of the hood can be cut away.

Items Not Affected By The Conversion

Transmission- Just be sure to use the correct input shaft bearing in the crank.
Bellhousing-
Valve Covers
Water Pump
Altenator
Clutch
Timing Cover
Radiator
Timing Chain
 
P

Pinebluffracer

New Member
Jan 25, 2006
33
0
0
Jan 28, 2006
#4
  • Jan 28, 2006
  • #4
Wow! Vristang

I think I need to put you on my Christmas card list. That sounds like some thorough information.I scanned the info, but will do a much more slow read and take some notes, so I can start planning.

Dsstang U2 I will look you up in the very near future for some of those parts.
I am putting this 302 back in now, but don't know how long it will last. I think one of the previous owners buzzed some nitro through it. They promised it never happened, but Im finding some of their tales were a little tall. I consider myself a decent car buyer. I admit I through all my better instincts out the window on this one. However, I am having a ball working on this thing. Im changing Rack, gaskers, clutch (putting in centerforce street/strip) and Jegs H-pipe(front, rear seals, pan, not the heads) and a few lines and hoses. We might get a little more series after I drive it a short while.

You guys are great thanks again.
 

dastang2

Active Member
Dec 11, 2003
2,020
0
46
tx
Jan 29, 2006
#5
  • Jan 29, 2006
  • #5
no problem
 
P

Pinebluffracer

New Member
Jan 25, 2006
33
0
0
Jan 30, 2006
#6
  • Jan 30, 2006
  • #6
Well... I looked at the main bearings and there was some discoloration. So, now I am considering buying a new short block 302 or just building my 351W. I wonder what would be the least expensive route. I know what would be the quickest route, buying teh new 302 short block. any advise here?
 

90NotchBack

New Member
Feb 15, 2004
306
2
0
Loxahatchee/Pembroke Pines, FL
Jan 30, 2006
#7
  • Jan 30, 2006
  • #7
I went through this when my 302 took a crap. After a lot of thinking I deiced to build a 351W. I built a fairly stock Windsor. I'm very happy with my choice. The car goes 12.60 which shocked me. I thought it would go low 13's. Now I'm up set I should of went after this motor. It only has 9:5:1 compression and a small cam shaft and stock 69 351 Heads. I should of ported the heads and intake and gave it more compression like 10:5:1 and a nice size cam shaft. Oh well it leave room for next rebuild.
 

88Stangboy

Banned
Dec 12, 2005
342
0
0
Greenville, SC
Jan 30, 2006
#8
  • Jan 30, 2006
  • #8
Buy you a cheap 393 crank from Scat, they're like $395, you can use stock 351 rods, pistons, etc with it. Have some older 69-70ish 351 heads ported and stick on it with a decent cam and go with that, should be pretty damn fast. Or get some forged 302 pistons from a 5.0 and use those with it. Bore is same size on 302 and 351, the 351's stroke is longer, resulting in the increased deck height.
 

dastang2

Active Member
Dec 11, 2003
2,020
0
46
tx
Jan 30, 2006
#9
  • Jan 30, 2006
  • #9
88Stangboy said:
Buy you a cheap 393 crank from Scat, they're like $395, you can use stock 351 rods, pistons, etc with it. Have some older 69-70ish 351 heads ported and stick on it with a decent cam and go with that, should be pretty damn fast. Or get some forged 302 pistons from a 5.0 and use those with it. Bore is same size on 302 and 351, the 351's stroke is longer, resulting in the increased deck height.
Click to expand...


you get the 3.85 stroke crank for the 393 and use stock 351 rods with stock 302 pistons.
 

88Stangboy

Banned
Dec 12, 2005
342
0
0
Greenville, SC
Jan 30, 2006
#10
  • Jan 30, 2006
  • #10
dastang2 said:
you get the 3.85 stroke crank for the 393 and use stock 351 rods with stock 302 pistons.
Click to expand...

Correct, the 3.85 stroke of the stroker crank increases the stock (3.50) stroke of the 351 and you use stock 5.956 351 rods and find some forged pistons out of a 5.0, i think, correct me if im wrong on this, they put forged pistons in the 88-late 92 5.0's, in 93 i think they switched to hyperuetectics, didn't they? Or was it late 93 they made the switch? And you can also dig around for some foot ball rods from 351 truck engines, they're a little more stout. Clean the stock rods up, have them shot peened and use some ARP hardware in them, and make sure you use a stud girdle depending on HP level, i always used them no matter what, just to be sure, my dad always used them no matter what on Ford engine's, just to be safe.
 
P

Pinebluffracer

New Member
Jan 25, 2006
33
0
0
Jan 30, 2006
#11
  • Jan 30, 2006
  • #11
Dang, out in my shed I found some .030 forged pistons that were meant for a 302. I guess I could use these pistons for the 351 or I can look at the pistons I have in my current 302, now on engine stand. Is that 3.85 stroke stock for a 351? Or is it considered a Stroker crank? Or is the 351 just considered a stroker period? side note...Not sure if this is a bad word, but I had a 383 Chevy a while ago built by Bo Laws.
If I bring this 351w bare block I have down to the machine shop,I could have that bored to fit these pistons(30 over) get a 393 crank and find some truck rods out and letter eat. Well i'll need a bigger pan and lower intake. oh, longer distributer and 1/2 holes for the heads.
 
P

Pinebluffracer

New Member
Jan 25, 2006
33
0
0
Jan 30, 2006
#12
  • Jan 30, 2006
  • #12
Not sure if this attached... but is the a cobra intake or a GT40?
 

88Stangboy

Banned
Dec 12, 2005
342
0
0
Greenville, SC
Jan 30, 2006
#13
  • Jan 30, 2006
  • #13
Pinebluffracer said:
Dang, out in my shed I found some .030 forged pistons that were meant for a 302. I guess I could use these pistons for the 351 or I can look at the pistons I have in my current 302, now on engine stand. Is that 3.85 stroke stock for a 351? Or is it considered a Stroker crank? Or is the 351 just considered a stroker period? side note...Not sure if this is a bad word, but I had a 383 Chevy a while ago built by Bo Laws.
If I bring this 351w bare block I have down to the machine shop,I could have that bored to fit these pistons(30 over) get a 393 crank and find some truck rods out and letter eat. Well i'll need a bigger pan and lower intake. oh, longer distributer and 1/2 holes for the heads.
Click to expand...


No, the stock 351 stroke is 3.50, the "393" crank, has a 3.85 stroke. The 302 and 351 have the same size bore, 4.00. The deck height on the 351 is higher.
 
P

Pinebluffracer

New Member
Jan 25, 2006
33
0
0
Jan 30, 2006
#14
  • Jan 30, 2006
  • #14
Oh.. great thanks. so an extra .35 stroke and I'll decide later on the bore size. may just get it honed.
I have heard it's not a good idea to bore a 302, because it runs a little hot already (narrow cylinder walls). Is there any truth to that and would it be true for a 351, also, if the previous question is also correct.
 

88Stangboy

Banned
Dec 12, 2005
342
0
0
Greenville, SC
Jan 30, 2006
#15
  • Jan 30, 2006
  • #15
Pinebluffracer said:
Oh.. great thanks. so an extra .35 stroke and I'll decide later on the bore size. may just get it honed.
I have heard it's not a good idea to bore a 302, because it runs a little hot already (narrow cylinder walls). Is there any truth to that and would it be true for a 351, also, if the previous question is also correct.
Click to expand...

As far as boring an engine. Its never a good idea to go over .060, on any engine. I know on some older Chevy 265 v-8's you can bore them to .125 over, which essentially makes them a 302. But its never a good idea to do that, if you can get by with honing, do it, no need to bore unless the cylinder is seriously out of round or has to much taper. If you can get away with it, just hone them .010 over. My 306, (.030 over 302) has no cooling issues with a F cam and stock radiator. So i personally dont know about that myth, i dont think there is any truth to it. For a 351, same principle goes, never go past .060 over. Your not going to see much if any gain from boring the engine over.
 
You must log in or register to reply here.

Similar threads

T
Oil burning on my recently buil 302
  • The blk67
  • May 15, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
250
Fox 5.0 Mustang Tech May 15, 2026
Noobz347
Ford truck engine swap issues
  • keel
  • Jul 7, 2026
  • Other Auto Tech
Replies
17
Views
779
Other Auto Tech Jul 13, 2026
General karthief
D
351w swap shifter is not lining up
  • duckman0926
  • Aug 6, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
3
Views
265
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 7, 2025
limp
A
Resolved 302 oil leak when running
  • AlexM556
  • Sep 8, 2026
  • Classic Mustang Specific Tech
  • 2
Replies
36
Views
1K
Classic Mustang Specific Tech Nov 1, 2026
manicmechanic007
Engine Looking for suggestions and or ideas
  • PonyGTrider
  • Aug 25, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
730
Fox 5.0 Mustang Tech Sep 7, 2026
PonyGTrider
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?