• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

315 in the back(tires)

  • Thread starter Thread starter mustangsally93
  • Start date Start date Sep 4, 2006

mustangsally93

New Member
Sep 26, 2005
281
0
0
Omaha,NE
Sep 4, 2006
#1
  • Sep 4, 2006
  • #1
What all do you need to put 315 in the back of a 93 fox? I'm plaining on upgrading to the baer brakes and 5 lug 31 spline axles. I don't want to tube the the car. Do I have to flare the frenders? What about control arms?

Thanks.
 

old_blue

15 Year Member
Nov 3, 2003
1,783
282
124
Sep 4, 2006
#2
  • Sep 4, 2006
  • #2
mustangsally93 said:
What all do you need to put 315 in the back of a 93 fox?
Click to expand...

more room!

Get rid of the quad shocks,so probably new control arms. hope it isn't lowered. Someone was running 315's with the tails still on but most get rid of them because they will rub. Do a search, I can't remember who it was that ran them.
 
T

TheUser

Active Member
Jul 25, 2003
1,859
1
36
Springfield, MO
Sep 4, 2006
#3
  • Sep 4, 2006
  • #3
probably will depend on the brand you run. Nitto's run small, so running Nitto 315's would be close to running BFG 295's I'd estimate (I've heard Nitto 275's are like BFG 255's, so I just did the math).

I've only seen one picture of a fox w/ 315's. I think it was a coupe, white if I remember correctly and those tires are HUGE!. I think he had to mini tub it. My 275's rub a little (I think on the inner fender w/ the back side of the tire) when I go up a very steep incline at an angle w/ any speed. BFG 315's are almost a full 1.6" wider than my 275's, so have fun w/ that. I'd assume flaring the fenders will be mandatory.

The only way to get around mini-tubbing that I can see is if you used a small backspace and had the wheels stick out from the fenders like an inch and a half, which would look stupid in my opinion.

Hissing Cobra has 295 BFG's on the back of his 79 and I think all he had to use was an air bag on one side, so that might be an option w/ 315 Nitto's, but 315 BFG's will probably require more than that.

Good luck
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,249
17,932
224
Massachusetts
Sep 4, 2006
#4
  • Sep 4, 2006
  • #4
I also beleive keeping the Fox rear offset is vital to even being close to running that big of a tire depending on what wheels you go with.

The baer setup does push the wheel out slightly, but not at much as SN95. If you want rear disk, a Cobra setup using North Race Cars brackets and Fox-lenght 5-lug axles may be in your better interest. Cheaper too
 

85_SS_302_Coupe

it sucks (I know) to be on the receiving end
15 Year Member
Nov 11, 2003
6,945
1,598
223
Northern KY
Sep 4, 2006
#5
  • Sep 4, 2006
  • #5
a MIRACLE.

I'd say just about all the big dog cars you see with 315ish size tires out back are probably mini-tubbed.
 

90lxcoupe

20+ Year Stangneter
Oct 7, 2003
3,596
350
134
Sep 4, 2006
#6
  • Sep 4, 2006
  • #6
it was bert306 that had the 315's on his car, also hatchbacks have more room than notchbacks in the rear and convertible wheelwells have the least room
 

wythors

Get off my lawn!!!
Founding Member
May 17, 2000
2,277
35
69
C Addle
Sep 4, 2006
#7
  • Sep 4, 2006
  • #7
I own a 93 convertible and a 96 Cobra. I put Goodyear GS-D3's in 315/35 on 17x10.5's on the Cobra and I'm here to tell you that there is no way in hell that they would fit on the 93 without major modifications.
 

85_SS_302_Coupe

it sucks (I know) to be on the receiving end
15 Year Member
Nov 11, 2003
6,945
1,598
223
Northern KY
Sep 4, 2006
#8
  • Sep 4, 2006
  • #8
wythors said:
I own a 93 convertible and a 96 Cobra. I put Goodyear GS-D3's in 315/35 on 17x10.5's on the Cobra and I'm here to tell you that there is no way in hell that they would fit on the 93 without major modifications.
Click to expand...

That's one of the best thing about the '94+ cars is that they can handle huge tires.
 
C

caseywan

Member
Apr 7, 2006
157
0
17
Chicago, IL
Sep 4, 2006
#9
  • Sep 4, 2006
  • #9
Ok, noob question. What exactly does mini-tubbed mean??
 

85_SS_302_Coupe

it sucks (I know) to be on the receiving end
15 Year Member
Nov 11, 2003
6,945
1,598
223
Northern KY
Sep 4, 2006
#10
  • Sep 4, 2006
  • #10
caseywan said:
Ok, noob question. What exactly does mini-tubbed mean??
Click to expand...

tubbed means you've cut the rear inner fenders out and welded in "tubs" which are basically just wide sheet metal humps so that the tires can fit under the car without rubbing anything. mini-tub is just a smaller and less serious modification. Typically if you have a car that runs the big slicks in the back, that's usually the full tubbed and totally custom rear end. On a car like ours you can minitub and just cut out the inner fenders without doing anything to the suspension.




This car has been mini tubbed, but also has a custom suspension and shortened rear axle in order to make those huge steam rollers fit under the fenders. That's a bit of an extreme though...you won't fit tires that wide under your car unless you relocate the control arms and really do a custom suspension yourself.
 

marine_2003

Member
Jun 6, 2005
427
0
16
Lake County, FL
Sep 4, 2006
#11
  • Sep 4, 2006
  • #11
There is a thread somewhere on here that a guy did with a blue fox and tailpipes and ran the 315's with no tub at all. He ran the Nitto DR, because like said earlier they run small.
 

marine_2003

Member
Jun 6, 2005
427
0
16
Lake County, FL
Sep 4, 2006
#12
  • Sep 4, 2006
  • #12
Heres the thread

http://forums.stangnet.com/showthread.php?t=599575
 

mustangsally93

New Member
Sep 26, 2005
281
0
0
Omaha,NE
Sep 4, 2006
#13
  • Sep 4, 2006
  • #13
http://forums.stangnet.com/showthread.php?t=599575
 

mustangsally93

New Member
Sep 26, 2005
281
0
0
Omaha,NE
Sep 4, 2006
#14
  • Sep 4, 2006
  • #14
I found the thread but it really say nothing how he did it other than ranger axles and cutting the in side of the frender. I was hoping for a more detailed walk though. I'm not going to be running tips just a 3 inch down pipe. I was going to just do the 5 lug and put the tires and rims on and then take it to a body shop and have them flare the frenders around the tires.. What about that?

Thanks
 

marine_2003

Member
Jun 6, 2005
427
0
16
Lake County, FL
Sep 4, 2006
#15
  • Sep 4, 2006
  • #15
I would shoot him a message, and see how he did it.
 

mustangsally93

New Member
Sep 26, 2005
281
0
0
Omaha,NE
Sep 4, 2006
#16
  • Sep 4, 2006
  • #16
marine_2003 said:
I would shoot him a message, and see how he did it.
Click to expand...


Yea I well but I think when he sold it he stoped coming on stangnet.


But I'll try it.
 

mustangsally93

New Member
Sep 26, 2005
281
0
0
Omaha,NE
Sep 4, 2006
#17
  • Sep 4, 2006
  • #17
mustangsally93 said:
Yea I well but I think when he sold it he stoped coming on stangnet.


But I'll try it.
Click to expand...


Yea he has to be gone. His pm box is full.
 

tunedin302

I AM the law!!!
Jul 29, 2004
1,251
2
36
Pennsylvania
Sep 4, 2006
#18
  • Sep 4, 2006
  • #18
Mustang5L5 said:
The baer setup does push the wheel out slightly, but not at much as SN95.
Click to expand...

Baer = .20" each side
SN95 = .75" each side
 

mustangsally93

New Member
Sep 26, 2005
281
0
0
Omaha,NE
Sep 4, 2006
#19
  • Sep 4, 2006
  • #19
I guess maybe a custom rear end and a little body work.
 
You must log in or register to reply here.

Similar threads

8
87 lx 4cyl to v8 project 4 lug disc conversion questions
  • 87lx428
  • Mar 24, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
498
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Mar 25, 2026
87lx428
8
Which SN95 axles for 93 LX, disc brakes, ABS rings?
  • dan50
  • Mar 22, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
15
Views
415
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Apr 3, 2026
7-UP BILL
J
Wheels-Tires Need Some Help - Brakes Upgrade/Wheel fitment
  • jaygee15
  • Dec 8, 2025
  • Fox 5.0 Mustang Tech
  • 3 4 5
Replies
81
Views
2K
Fox 5.0 Mustang Tech May 6, 2026
AeroCoupe
H
Forced Induction On3 Turbo Kit- Parts list NEEDED - 302 Stock Motor
  • Hirothecool1
  • Feb 27, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
21
Views
1K
Fox 5.0 Mustang Tech Mar 7, 2026
slow84lx
S
J
2004 Mustang 3.8L V6 vibrations above 65 MPH and differential leaks
  • joeybuddy96
  • Mar 16, 2026
  • SN95 V6 Mustang Tech
Replies
16
Views
533
SN95 V6 Mustang Tech Tuesday at 2:38 PM
joeybuddy96
J
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?