• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

351 efi distibutor?

  • Thread starter Thread starter BK_CAULEY
  • Start date Start date Feb 10, 2007
Status
Not open for further replies.
  • 1
  • 2
Next
1 of 2 Next Last

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Feb 10, 2007
#1
  • Feb 10, 2007
  • #1
i am trying to get a distributor for my 351 build. and all i can find is the efi truck ones with seperate wiring for th pip and a seperate wiring harness for the tfi. the parts store has one for a 89 ford truck witha 351 and efi and it looks just like my mustang one where all the connectorers plug into the tfi and the tfi plugs into the bottom. will this one work? i cant afford a msd unit and ther advance auto one is way cheaper. i just need to know if the 1989 efi will work. should the 1989 351 efi distributor be longer?
 
2

2002BLGT

Well-Known Member
Dec 18, 2003
2,945
4
59
Bedford VA
Feb 10, 2007
#2
  • Feb 10, 2007
  • #2
MSD 8452 with roller cams , 8453 with non roller cams , dont skimp on the distributor if you are going to spend the money on doing the swap to begin with
 
2

2002BLGT

Well-Known Member
Dec 18, 2003
2,945
4
59
Bedford VA
Feb 10, 2007
#3
  • Feb 10, 2007
  • #3
2002BLGT said:
MSD 8452 with roller cams , 8453 with non roller cams , dont skimp on the distributor if you are going to spend the money on doing the swap to begin with
Click to expand...

88 model F150 should have had the module on the distributor , but the gear on it will be for non roller cam engine so you will have to change the gear to run on a roller cam
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Feb 10, 2007
#4
  • Feb 10, 2007
  • #4
85 motor

i am using the motor out of an 1985 f-150 that isnt a roller cam is it? what is the advantage of a roller motor?
 
2

2002BLGT

Well-Known Member
Dec 18, 2003
2,945
4
59
Bedford VA
Feb 10, 2007
#5
  • Feb 10, 2007
  • #5
BK_CAULEY said:
i am using the motor out of an 1985 f-150 that isnt a roller cam is it? what is the advantage of a roller motor?
Click to expand...

you can use stock roller lifters and roller cam instead of buying the linked conversion lifters to run a roller cam , most people just stick with hydraulic cams from what I have seen on most mild build ups
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Feb 10, 2007
#6
  • Feb 10, 2007
  • #6
the 85

so im assuming the 85 isnt a roller motor? how much HP can you get out of a hydraulic cam and lifter motor? cause i have a procharger off of my current setup and i plan on turning the boost up pretty good when i get this thing together. will i be safe with a hydraulic motor? or do i need a roller motor? and if i do what year, make and model vehichles did these come in?
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Feb 10, 2007
#7
  • Feb 10, 2007
  • #7

The late and mid 90's trucks had 351W engines with roller cams. 351W blocks that are roller cam compatible have the casting number F4TE located near the starter.
 

Attachments

  • Roller vrs flat tappet cam.gif
    35.8 KB · Views: 472

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Feb 10, 2007
#8
  • Feb 10, 2007
  • #8
distributor

i have a 1985 motor so its not a roller motor and a 1989 efi distributor which im guessing is the non roller distributor. so if i want to upgrade to a roller motor later do i have to as mentioned above change the gear and if i do how can i obtain just the gear? and i measured today and my new 351 dist and my 302 dist are the same length but the 351 dist has a wider shaft. are they supposed to be the same length?
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Feb 10, 2007
#9
  • Feb 10, 2007
  • #9
jrichker said:

The late and mid 90's trucks had 351W engines with roller cams. 351W blocks that are roller cam compatible have the casting number F4TE located near the starter.
Click to expand...
Excellent post JR
Well put.



BK_CAULEY said:
i have a 1985 motor so its not a roller motor and a 1989 efi distributor which im guessing is the non roller distributor. so if i want to upgrade to a roller motor later do i have to as mentioned above change the gear and if i do how can i obtain just the gear? and i measured today and my new 351 dist and my 302 dist are the same length but the 351 dist has a wider shaft. are they supposed to be the same length?
Click to expand...

something is wrong.
the 351w dist should be about .75-1" longer. (I don't remember exactly).

You can get the roller dist gears anywhere. Summit, Jegs, local parts stores, etc.
They will need the diameter of the dist shaft (I think there were 2 sizes used on the 351w, so measure yours).




jason
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Feb 11, 2007
#10
  • Feb 11, 2007
  • #10
parts store

yea i ordered a replacement distributor for a 1989 ford truck with a efi 351 and i measured the length from the base where it sits on the intake to the top of the gear and it was 3.5". it was the same on the 302. can somebody tell me if this is the correct length or if the distibutor i compared the new 351 piece to isnt for a 302 perhaps.
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Feb 11, 2007
#11
  • Feb 11, 2007
  • #11
??

well can anybody help me?
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Feb 11, 2007
#12
  • Feb 11, 2007
  • #12
I'm going up to my garage today.
I will try to measure a 302 dist and a 351w dist.

I won't be able to post results until late tonight though...

jason
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Feb 11, 2007
#13
  • Feb 11, 2007
  • #13
thanks

thanks man. i dont know what i would do without this forum. i hope to god i have the right one . i guess i will know as soon as you get the numbers posted.
 

86nu

New Member
Jan 6, 2007
94
1
0
Birmingham, Al
Feb 11, 2007
#14
  • Feb 11, 2007
  • #14
vristang said:
I'm going up to my garage today.
I will try to measure a 302 dist and a 351w dist.

I won't be able to post results until late tonight though...

jason
Click to expand...

its a good bit longer on a 351 dizzy

my friend has a 6al wired up to an 89 bronco dizzy and it runs 6.3x's all day long and has yet to have a problem with it
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Feb 12, 2007
#15
  • Feb 12, 2007
  • #15
any numbers yet?

does anybody have any measurements for me? what imk looking for is a length from the base of the distributor where it hits the intake to the top or bottom of the gear and an over all shaft .length
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Feb 19, 2007
#16
  • Feb 19, 2007
  • #16
DISTRIBUTOR PROBLEM SOLVED

HERE IS A LETTER I WROTE TO VRISTANG HOPE THIS HELPS SOMEBODY OUT THERE,

ok i got tired of waiting and went ahead and bought an MSD piece. so the verdict is, get ready for it.....THERE THE SAME LENGTH. i know, i know your thinking deck height and all that but its basic geometry(i will come back to his later). so anyways i got the dist in from msd and have the one out of my 5.0 302 and measured them with a caliper and the base to gear length are the same length. the only difference is the shaft thickness. i thought maybe i got the wrong part so i called MSD's tech support and the guy was nice enough to put me on hold and go pull the parts and measure them while on the phone with me and he got the same measurements i did. and i know people (maybe even you) will try to argue me down about it but its right. i put the distributor in the 351 and it fits. its currently not running becaue iam putting on better heads as you saw in my thread but it does work. the shafts are thicker and thats it my 302 shaft measured(with a caliper) .28125 and my new msd 351 shaft measured .53125 so ruffly a 1/4 inch difference or 1/8th all the way around. i have a drawing but have no way to attach it since it was done in autocad but i will try to explain it. its a v shape it gets taller but also gets wider so the top to base line dimension doesnt move just the height and lengths. if you can give me an email i can send from my email i will make a DXF file of it and send it to you. bottom line the are the same length just different shaft thickness's. i dont see how nobody as caught or researched this before. but i have done the research and have compared the two parts side by side and got accurate measurements. i will try and make a tecnical write up on it and make a MS paint drawing to better explain it and maybe it can go in the stickies to help others in the future. and i know im gonna catch a bunch or crap saying im wrong but i know whats right if you want i can get pics of the two side by side and give you part numbers off both pieces and let you see, or maybe you can measure yours in your shop and see for yourself. if you want me to explain or want any proof just let me know. thanks, Keith Cauley.

AND THE MEASUREMENTS ARE NO WHERE NEAR CLOSE ITS JUST AN EXAMPLE!!
 

302RollinHard

New Member
Sep 26, 2005
0
0
0
Columbus, OH
Feb 19, 2007
#17
  • Feb 19, 2007
  • #17
Very very interesting BK. I don't think people will try to argue you down, or they shouldn't since you did all the footwork. Just make sure to check for distributor end play when you install. You don't wanna screw up that nice MSD piece if you are going to install it. Been there done that, paid for another one.......
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Feb 19, 2007
#18
  • Feb 19, 2007
  • #18
OH I AM!!

ouch i bet you wont make that $320 mistake again. and i checked for play today and didnt seem to have any. you couldnt just buy another gear? or did it break the shaft?
 
8

86bluecobra

Advanced Member
Dec 20, 2004
4,265
12
69
B.C. Canada
Feb 19, 2007
#19
  • Feb 19, 2007
  • #19
It shouldn't be a surprise that they are the same length because the timing chain cover from a 302 fits a 351w. The deck hieght is where the heads mount to the base of the block that is the difference between the 2 engine blocks.
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Feb 19, 2007
#20
  • Feb 19, 2007
  • #20
yep

that what i was thinking, and thats what my little drawing is showing. i have had so many people say they are 3/4 and 1" longer and it just wasnt adding up. so i felt like i had resovle this matter. im surprised no body has tried to disagree with me yet. i just got through with a nice little write up on how and why. maybe one of the moderators will put it in the stickies. cause i know a bunch of people wanting to do the swap will need to know this. and if anyone on a budget needs a distributor you can get on for a 1989 f-150 with a 5.8 thats the only year that will work. and if you want to run the roller 351 you have to change the gear, i have all the part numbers and what not if anyone needs them. and contrary to belief the lightning distributor will not work. the p.i.p and t.f.i are controlled seperatly, as where our cars p.i.p signal runs through the t.f.i module.

86bluecobra-thanks for the head selection advice. i got a set on the way.
 
  • 1
  • 2
Next
1 of 2 Next Last
Status
Not open for further replies.

Similar threads

B
Electrical Why does my fox body keep frying eecs
  • brandyn200
  • Jun 20, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
533
Fox 5.0 Mustang Tech Jun 25, 2026
AeroCoupe
F
Fox 1990 Mustang GT 5.0 A9L – Engine suddenly shuts off but immediately restarts when key turned
  • FishermansFriend
  • Aug 9, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
16
Views
702
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 30, 2026
General karthief
Electrical 88 EEC Injectors batch firing ?
  • Dustin 86GT
  • Dec 8, 2025
  • Fox 5.0 Mustang Tech
Replies
10
Views
665
Fox 5.0 Mustang Tech Jan 8, 2026
gkomo
Resolved 93 Mustang 5.0 - Cranks but does not start
  • dan50
  • Jul 18, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
504
Fox 5.0 Mustang Tech Jul 18, 2026
dan50
S
Preparation for Holley Terminator X install – Foxbody 306 (electrical fan, alternator, MSD Ignition, etc)
  • So_Flo
  • Mar 1, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
22
Views
3K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Mar 4, 2026
General karthief
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?