• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

4.0L on 302 block

  • Thread starter Thread starter Ardent
  • Start date Start date Mar 19, 2007
A

Ardent

New Member
Dec 1, 2006
11
0
0
Mar 19, 2007
#1
  • Mar 19, 2007
  • #1
I've got a project in mind and I want a really small bore Ford small block for it. I'm wondering if on a 302 block I can get Scat to custom grind a short stroke crank, and with the right piston combo, get a roughly 4L displacement for a screaming little smallblock for a custom, ultralight, non street legal road racer.

All the above seems like it will work, not hard just $, but where I run into question marks is with the engineering of it, mainly the now very short stroke ~4" bores. How is having a stroke much shorter than your bore diameter going to affect the engine? Valve lift will be lower, or faster, but the amount of volume to move is lower as well by 20%. What I'm after here is a top end power band, low end torque is going to be non-existant, I'm aware. Just wouldn't mind hearing from people who know a lot more than I do on the subject.
 
B

Boss 351

Here sthhhhhhhheeeve take a picthh of my man flowe
Jul 13, 2003
2,433
23
48
Canada
Mar 19, 2007
#2
  • Mar 19, 2007
  • #2
??? okay then just get yourself a 289 block (roughly 4.8L) or build up a 3.8L V6... But I don't understand the point of wanting a 4.0L "302"
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Mar 19, 2007
#3
  • Mar 19, 2007
  • #3
The first Windsor engine produced in 1962 was a 221 cu in V8, from which all of the 255, 260, 289 and 302 engines descended. I recommend that you spend some time with Google and do some searching on Windsor engine. See http://en.wikipedia.org/wiki/Ford_Windsor_engine for a short tour with bore, stroke, valve sizes, and engine weights.
 

BlooDReigN

Member
Feb 22, 2004
283
1
16
Calgary, Alberta
Mar 19, 2007
#4
  • Mar 19, 2007
  • #4
The only advantage I could see to this is that you could probably rev it higher than most Hondas But you would also have the same issue they do with having little low end torque and not making much power til higher rpm's.
 

Woodrow

Founding Member
May 19, 2002
183
0
0
Atlanta/Auburn
Mar 19, 2007
#5
  • Mar 19, 2007
  • #5
Thats a dumb idea, but how high are you wanting to turn it? Are you running in a a head restricted class or something?
 
A

Ardent

New Member
Dec 1, 2006
11
0
0
Mar 20, 2007
#6
  • Mar 20, 2007
  • #6
For the fellow who brought up the 221, 260 etc I'm well familiar but I'm building on a 4 bolt main block (not available in the older smaller 3.5" or 3.8" bores) and all the internals of those old engines are cast pieces of junk, not something I want to build on. Hence the 8.2" deck, 4" bore block.

As for why, I beg to differ but it's not a "stupid idea" as one here put it. What I'm after is a powerband running up to, maybe over 9,000rpm. I love the sound of small bore V8's screaming down the track, and like how they drive. One of my favorites for sound are tuned Rover 3.5 and 4.0L V8's, but I prefer a small block Ford's design and aftermarket. So, I want to build a screaming small block. As for the lack of torque down low, not really an issue, this is a track toy only for track days at Spokane, WA, and Mission BC (Canada). The whole chassis minus engine/trans will be around 1200lbs, so huge power and torque is not required. This isn't for any particular class, just a toy and personal curiousity for me. I've been riding supersports and superbikes for years and want a car that approximates the performance and feel of my bikes, but with an American V8, and a screaming little one.

I know going a bit below 289 isn't going to be a challenge, I can do that on production cranks, but I'm after 245ci range. The thing will sound unreal, if it works.
 

BlownFiveLiter

have car, will race....wait, it doesn't run
15 Year Member
Nov 29, 1999
3,133
18
108
Chicagoland
Mar 20, 2007
#7
  • Mar 20, 2007
  • #7
I think it's kind of a cool idea, but you're going to run into the problem of having an expensive valvetrain that can sustain the RPM you're looking for. You're going to need shaft mounted rockers for sure with 9,000 RPM or greater. Solid roller lifters are also a must at that point. As much as you like the idea, maybe a 4.6 wouldn't be a bad tradeoff since they're meant to rev?
 

powertrax91

Founding Member
Mar 13, 2002
598
0
17
New York
Mar 20, 2007
#8
  • Mar 20, 2007
  • #8
Ardent
I know i'll get flamed for this... but have you considered a Mazda rotory engine?
 

blackened88lx

Active Member
Aug 9, 2006
0
4
28
Connecticut
Mar 20, 2007
#9
  • Mar 20, 2007
  • #9
Are you dead set on making it smaller? Why don't you just build a 302 to spin to 9k?
 

JChalfan

Member
Nov 27, 2002
551
0
16
Bellevue, WA
Mar 20, 2007
#10
  • Mar 20, 2007
  • #10
I think it's a pretty cool idea. Maybe not really practical, but still cool. I almost mentioned buick/rover v8's, but then I saw you already thought about those.

It seems to me you would need to have a custom crank built, and that would probably end up being very expensive.

I'd sure like to hear it if you ever get it built, it would sound like a freakin F1 car.
 

bullitstang1313

Member
Jan 21, 2003
713
0
16
Indianapolis / Columbus, Indiana
Mar 20, 2007
#11
  • Mar 20, 2007
  • #11
I think it sounds like a cool idea. As a mechanical engineer this idea really intrigues me. My first thought is around rotating mass. I think you'll want a lower rotating mass if you are going to rev the engine this high. This might be difficult to accomplish with a short stroke engine. You've got me thinkin on this one. I'm curious of what all would be needed to do such a thing.
 

Modular2v

Founding Member
Jun 30, 2002
3,222
23
99
oklahoma
Mar 20, 2007
#12
  • Mar 20, 2007
  • #12
just find yourself a 260 and stop trying to make a 302 something it should never become!
 

Woodrow

Founding Member
May 19, 2002
183
0
0
Atlanta/Auburn
Mar 20, 2007
#13
  • Mar 20, 2007
  • #13
Still a dumb idea, if you’re not running a head restricted class or a lbs per c.i. class. This thread might enlighten you... hell read the whole site there is several threads about destroking, ect. And people actually know their **** over there...
http://bbs.hardcore50.com/vbulletin/showthread.php?t=34077&page=2&highlight=rpm+displacement
 
A

Ardent

New Member
Dec 1, 2006
11
0
0
Mar 20, 2007
#14
  • Mar 20, 2007
  • #14
StangGT1995 said:
I think it's kind of a cool idea, but you're going to run into the problem of having an expensive valvetrain that can sustain the RPM you're looking for. You're going to need shaft mounted rockers for sure with 9,000 RPM or greater. Solid roller lifters are also a must at that point. As much as you like the idea, maybe a 4.6 wouldn't be a bad tradeoff since they're meant to rev?
Click to expand...

I agree with you on all counts here, I'm looking to sink some $ into this one, even been considering a Dart aluminum block. I already have a 4.6 in my GT convert, been playing with that for awhile, but I gotta face it I like non-electronic, pushrod valvetrain V8's. It's still a though as the 4.6 is downright cheap compared to what I'm looking at, but it's also a bulky engine with the OHC's.


powertrax91 said:
Ardent
I know i'll get flamed for this... but have you considered a Mazda rotory engine?
Click to expand...

Not my cuppa tea though I appreciate the engineering, I'd go for a high strung 4 cyl if I wanted to part from the V8, but for this build it's gotta be a Ford small block, love that sound.


blackened88lx said:
Are you dead set on making it smaller? Why don't you just build a 302 to spin to 9k?
Click to expand...

I've seen 289's that do, and 289 is the default choice if I either don't want to spend the money for the custom crank when the time comes or I run into too many problems trying to go sub 150ci.

Woodrow said:
Still a dumb idea, if you’re not running a head restricted class or a lbs per c.i. class. This thread might enlighten you... hell read the whole site there is several threads about destroking, ect. And people actually know their **** over there...
http://bbs.hardcore50.com/vbulletin/showthread.php?t=34077&page=2&highlight=rpm+displacement
Click to expand...

I'll give it a look and see, sounds interesting.
 
W

wicked84gt350

New Member
Aug 20, 2006
113
1
0
West palm bech florida
Mar 20, 2007
#15
  • Mar 20, 2007
  • #15
I always thought the 3 inch stroke was small enough And I know it is caperable of 9000 if built right. I would think a forged 5140 or 4340 steel crank that was balanced to 28oz and aluminum components would be light enough and the had the counter weights cut smoothed and shaped would definetly help
 

Mr. Rustypwnz

Advanced Member
Jun 1, 2005
1,761
63
69
indianapolis/ valdosta ga
Mar 20, 2007
#16
  • Mar 20, 2007
  • #16
turbo 2.3 ford with no exhaust pushin 30psi, ported head, essy cam, and a holset turbo with a hellacious intercooler, and a stand alone. I was building one of these this summer and damn they can be krazy fast, sound good, and if tuned right can be very reliable, and make 350-700hp depending on all the crap you want to do with it.
 

85_SS_302_Coupe

it sucks (I know) to be on the receiving end
15 Year Member
Nov 11, 2003
6,945
1,598
223
Northern KY
Mar 20, 2007
#17
  • Mar 20, 2007
  • #17
This is a bit silly if you think about it....you don't need 9k RPM if you can make the same power in 6k. Also if you're really serious about this, you can build a sick 289 with aftermarket parts but even then you're not going to save THAT much weight over a 302. Also, a shorter stroke 302 isn't going to make it any more ultra light than a stroked 347/302.

Back in the day it wasn't uncommon to see 289s pushing 8-9k RPM in race applications....with today's head technology you could possibly even see 10k if you invest in some serious valve components (titanium valves for example). Rick Anderson has built several 347/302s that redline around 8200RPM but you're talking some serious serious money spent in porting and your valve train, and then you're also talking about one season of racing before you have to rebuild.
 
You must log in or register to reply here.

Similar threads

6
Hey all,I’m putting together a 302 for my 1968 Mustang and wanted to post the combo + some questions to make sure I’m not missing crucial
  • 68_Disgustang
  • Feb 22, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
5
Views
1K
1965 - 1973 Classic Mustangs -General/Talk- Oct 19, 2026
mattcrp1
M
SN95 Desktop 363 Engine Combination - Looking for input
  • WhiteCobra95
  • Sep 8, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
11
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 6, 2025
Habu135
M
Resolved 1988 Foxbody - Overheating Summer
  • MDrisc
  • Oct 26, 2025
  • Fox 5.0 Mustang Tech
Replies
16
Views
1K
Fox 5.0 Mustang Tech Jul 17, 2026
fasterthangas
F
  • Locked
Engine Might have to get a Dart block but don't want to and if I do, then 363 instead of 331. Thoughts on what I've already bought so far.......
  • from6to8
  • Jul 8, 2025
  • Fox 5.0 Mustang Tech
Replies
2
Views
641
Fox 5.0 Mustang Tech Jul 8, 2025
Noobz347
J
Help Figuring Motor Choice(Possible future turbo)?
  • jaygee15
  • Dec 14, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
13
Views
926
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jan 3, 2026
Jarhead67
J
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?