• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

4 valve too clean

  • Thread starter Thread starter 1982matthew
  • Start date Start date Mar 30, 2008
1

1982matthew

New Member
Mar 14, 2008
42
0
0
Easton,Pa
Mar 30, 2008
#1
  • Mar 30, 2008
  • #1
So I had purchased a 93 GT with a intake backfiring problem and after checking the timing, wiring order, injectors, fuel pressure and rocker nuts, I pulled all the plugs and they all look like normally used plugs but on the #4 valve, it is clean an smells of unburned fuel. Does anybody have any suggestions...I will take any and all at this point, thanks. -Matt-
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,372
18,120
224
Massachusetts
Mar 30, 2008
#2
  • Mar 30, 2008
  • #2
Next step would be to determine if the plug is firing. How does the wire look going to it? Anything look broken or cracked on it?

How is the compression on that cylinder? If you test all 8, is it lower?
 
1

1982matthew

New Member
Mar 14, 2008
42
0
0
Easton,Pa
Mar 30, 2008
#3
  • Mar 30, 2008
  • #3
compression is fine and plugs and wires all new
 
L

lang williams

New Member
Jun 11, 2003
567
0
0
cleveland, oh
Mar 31, 2008
#4
  • Mar 31, 2008
  • #4
i'd guess either bad plug, bad plug wire, bad terminal in the dist cap.
 

dcurtis

10 Year Member
Jan 19, 2006
688
7
39
Mar 31, 2008
#5
  • Mar 31, 2008
  • #5
For some reason, one of the above most likely, that plug was not firing, my plugs were like that, but it was only because I let my cousin install 4 of them and he didn't press the wire all the way on. Should be a quik fix.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Apr 1, 2008
#6
  • Apr 1, 2008
  • #6
Cylinder balance test:
Warm the car's engine up to normal operating temperature. Use a
jumper wire or paper clip to put the computer into test mode. Start
the engine and let it go through the normal diagnostic tests, then
quickly press the throttle to the floor. The engine RPM should exceed
2500 RPM's for a brief second. The engine RPM's will increase to about
1450-1600 RPM and hold steady. The engine will shut off power to each
injector, one at a time. When it has sequenced through all 8 injectors,
it will flash 9 for everything OK, or the number of the failing cylinder
such as 2 for cylinder #2. Quickly pressing the throttle again up to
2500 RPM’s will cause the test to re-run with smaller qualifying figures.
Do it a third time, and if the same cylinder shows up, the cylinder is
weak and isn’t putting out power like it should. See the Chilton’s Shop
manual for the complete test procedure

Here's the link to dump the computer codes with only a jumper wire
or paper clip and the check engine light, or test light or voltmeter.
I’ve used it for years, and it works great.

See http://www.troublecodes.net/Ford/

[




If your car is an 86-88 stang, you'll have to use the test lamp or voltmeter method. There is no functional check engine light on the 86-88's except possibly the Cali Mass Air cars.



89 through 95 cars have a working Check Engine light. Watch it instead of using a test lamp.



Do a compression test on all the cylinders.
Take special note of any cylinder that shows up as weak in the cylinder
balance test. Low compression on one of these cylinders rules out the
injectors as being the most likely cause of the problem. Look at cylinders
that fail the cylinder balance test but have good compression. These
cylinders either have a bad injector, bad spark plug or spark plug wire.
Move the wire and then the spark plug to another cylinder and run the
cylinder balance test again. If it follows the moved wire or spark plug,
you have found the problem. If the same cylinder fails the test again,
the injector is bad. If different cylinders fail the cylinder balance test,
you have ignition problems or wiring problems in the 10 pin black &
white electrical connectors located by the EGR.

How to do a compression test:
Only use a compression tester with a screw in adapter for the spark
plug hole. The other type leaks too much to get an accurate reading.
Your local auto parts store may have a compression tester to rent.
If you do mechanic work on your own car on a regular basis, it would
be a good tool to add to your collection.

With the engine warmed up, remove all spark plugs and prop the
throttle wide open, crank the engine until it the gage reading stops
increasing. On a cold engine, it will be hard to tell what's good &
what's not. Some of the recent posts have numbers ranging from
140-170 psi. If the compression is low, squirt some oil in the cylinder
and do it again – if it comes up, the rings are worn. There should be
no more than 10% difference between cylinders. Use a blow down
leak test (puts compressed air inside cylinders) on cylinders that
have more than 10% difference.

See the link to my site for details on how to build your own blow
down type compression tester.
 
1

1982matthew

New Member
Mar 14, 2008
42
0
0
Easton,Pa
Apr 1, 2008
#7
  • Apr 1, 2008
  • #7
thanks ill try that toward the end of the week when i get a chance........
 
You must log in or register to reply here.

Similar threads

M
Electrical 93 5.0 No Injector Pulse
  • machinermac
  • Jul 26, 2026
  • Fox 5.0 Mustang Tech
Replies
15
Views
518
Fox 5.0 Mustang Tech Aug 1, 2026
Willybill32
K
Resolved Weird sound coming from a freshly rebuilt 5.0L
  • karhoot
  • Jun 24, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
397
Fox 5.0 Mustang Tech Jun 27, 2026
Mac131
1
Engine 91 mustang 302 Low acceleration car backfires pops and acts like it doesn’t want to take fuel
  • 1991Fox5.0
  • Oct 4, 2025
  • Fox 5.0 Mustang Tech
Replies
16
Views
1K
Fox 5.0 Mustang Tech Oct 6, 2025
1991Fox5.0
1
M
01 mustang 3.8 fuel pressure issue
  • Mhaley2006
  • May 29, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
4
Views
537
1996 - 2004 SN95 Mustang -General/Talk- Aug 9, 2026
JohnKay
J
Engine Looking for suggestions and or ideas
  • PonyGTrider
  • Aug 25, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
713
Fox 5.0 Mustang Tech Sep 7, 2026
PonyGTrider
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?