• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SVT Tech Forum

96 Cobra not blowing air through vents

  • Thread starter Thread starter cobrachris96
  • Start date Start date Jan 8, 2010
C

cobrachris96

New Member
Jul 5, 2002
10
0
0
Oklahoma City. OK
Jan 8, 2010
#1
  • Jan 8, 2010
  • #1
My 96 Cobra is not blowing any air through the vents. It only blows air through the defrost and floor vents but not the main vents. I looked under the hood and noticed this red broken cable/hose. What is this? A vacuum hose? I'm not much of a mechanic but if its something fairly easy to fix, I don't mind getting under the hood. Any thoughts/ideas? Thanks

 

pedro

Founding Member
May 20, 2001
432
6
29
Jan 8, 2010
#2
  • Jan 8, 2010
  • #2
Yup, your problem is probably because of that broken vacuum line. Just replace it or try to plug it in. This happened to me a couple years ago, and my A/C fan was working like you're saying.
 
K

Kilgore Trout

Fried or Broiled ?
10 Year Member
Mar 30, 2005
4,749
95
134
Jan 8, 2010
#3
  • Jan 8, 2010
  • #3
The vents are controlled by vacuum. When the vacuum fails the vents default to blow defrost for safety reasons.
 
C

cobrachris96

New Member
Jul 5, 2002
10
0
0
Oklahoma City. OK
Jan 8, 2010
#4
  • Jan 8, 2010
  • #4
OK, I went out to the garage and started the car. I then held the two ends of the vacuum line together and I heard a click. After that, air started blowing through the vents. Can I just connect the pieces together with electrical tape or does it need to be an air tight connection?
 
P

Price1

Member
May 11, 2003
109
0
16
Dryfork, WV
Jan 9, 2010
#5
  • Jan 9, 2010
  • #5
Needs to be an airtight connection. You might use a piece of very small diameter rubber tubing to connect them. Or, you might use a shrinkwrap tube. You might also find a specialty vacuum type connector at an auto parts - I think I've seen those before at Vatozone or Advance Auto.

Make sure you do it right and make it permanent.

Good luck....
 
C

cobrachris96

New Member
Jul 5, 2002
10
0
0
Oklahoma City. OK
Jan 9, 2010
#6
  • Jan 9, 2010
  • #6
I went to Autozone and they gave me a small piece of rubber tubing. Unfortunately, there isn't enough of the vaccum line sticking out on the right side to slide the tubing over it.

I had the car in the shop at the dealership last week to get a new power steering pump installed. I'm not sure if they broke it or not but I may take it by there next week and see if they'll do something about it.
 
You must log in or register to reply here.

Similar threads

B
A/C Issues
  • Boats90GT
  • Jun 10, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
115
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 11, 2026
Mcmahst
D
Engine 85 GT Backfires through Carb
  • DienstXIV
  • Oct 3, 2025
  • Fox 5.0 Mustang Tech
Replies
19
Views
698
Fox 5.0 Mustang Tech Oct 7, 2025
85GTStangGuy
N
Edelbrock 1405 Setup
  • nathantaylor200
  • Nov 4, 2025
  • Classic Mustang Specific Tech
Replies
3
Views
243
Classic Mustang Specific Tech Nov 5, 2025
nathantaylor200
N
96 Cobra IMRC delete, dyno’d
  • Gunmonkey
  • Aug 29, 2024
  • SVT Tech Forum
Replies
2
Views
1K
SVT Tech Forum Nov 7, 2024
Gunmonkey
J
'96 Cobra: A/C gets weak and engine misfires under load when warm
  • jruhnke
  • Oct 22, 2025
  • SVT Tech Forum
Replies
2
Views
320
SVT Tech Forum Nov 20, 2025
nickyb
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SVT Tech Forum
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?