• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

A/C Blowoff

  • Thread starter Thread starter dcurtis
  • Start date Start date Mar 23, 2007

dcurtis

10 Year Member
Jan 19, 2006
688
7
39
Mar 23, 2007
#1
  • Mar 23, 2007
  • #1
Ok, I bought a 91 GT about a week and a half ago, the car is basically perfect, but the guy I bought it from said he thinks the a/c is clogged or something, anyways, yesterday I started working on the a/c and it wasn't hooked up so I hooked it up, after that I checked it and it wouldn't come on, so I put some refrigerant in it, about half of a 12oz bottle and the a/c started coming on for a few seconds and then would go off, after I got about one full bottle and maybe a 1/4 of another in it it would stay on, the air was cold and I thought I was done, got in the car to start putting the rest of the second bottle in because it says to put in 2 pounds and 2oz of refrigerant in it, while I was in the car I had the air on Max A/C and the first spot on the nob that controls how hard the air blows,

heres my question, while I was in the car I tried to turn the air up to the hardest setting and the A/C spewed the refrigerant out of the little thing on top of it, it has a tiny hole with a spring in it, I guess it is for excessive pressure or something, so I took off the bottle of refrigerant and tried again and it does the same thing, it works fine on the lowest setting but if I turn it up it blows off, what is causing this????????? could it be clogged? if so how do I go about fixxing it?
Thanks for any help because I am stumpt
 

BlownFiveLiter

have car, will race....wait, it doesn't run
15 Year Member
Nov 29, 1999
3,133
18
108
Chicagoland
Mar 23, 2007
#2
  • Mar 23, 2007
  • #2
I'm not sure I follow. Your car leaks refrigerant when you turn your fan up to a higher setting? The two are completely unrelated to one another, so that makes no sense. Your compressor turns at whatever speed the belt turns it, and the pressure inside your system is the same regardless of whether the fan inside the car is on or not. You're not referring to the schraeder valve that you use to fill the system, and the refrigerant coming out of there are you? And please tell me you didn't put R134a into a system that takes R12 without flushing and doing a conversion?
 

dcurtis

10 Year Member
Jan 19, 2006
688
7
39
Mar 23, 2007
#3
  • Mar 23, 2007
  • #3
The system has already been converted, the pressure is coming out of a small hole with a spring in it on top of the compresser, as for the fan that does sound right, maybe it was when I give it gas, I will go check as soon as I post this.
 

backfocus

Member
Sep 3, 2004
254
3
18
Little Rock, AR
Mar 23, 2007
#4
  • Mar 23, 2007
  • #4
Sounds like your talking about the schraeder valve on the compressor. It could be faulty and it pretty easy to replace if the system is empty. Besides if the system was empty, the refrigerant went somewhere via a leak. I would put some leak dye in the system or pressurize it with nitrogen and find the leak first. And as was said, fan speed has very little to do with pressure.

That schraeder valve should have a cap on it to!
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Mar 23, 2007
#5
  • Mar 23, 2007
  • #5
There is a relief valve on top of the compressor that will open if the compressor pressure gets too high. This is due to the system being overcharge with too much refrigerant or it wasn't vacuumed down properly. Air left in an A/C system will cause poor cooling and an overpressure condition.

A R134 system uses 80% of the charge used with R12. That means you use 24-28 Oz R134a plus 4-6 Oz of R134a compatible oil.

Here's the recharge/conversion instructions.

R134a Air Conditioner Conversion


R134a = $7-$10 a can – takes 2 - 2 ½ cans.

R134a compatible oil = $5-$7 for an 8 oz bottle – better get 2 bottles.

Gauge set for recharging = $20-$120 – check out the pawn shops for a bargain before you pay retail. See http://www.harborfreight.com/for A/C charging gauges that you will need.

http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=92649 is the A/C charging gauges that you will need.

.

My current vacuum pump is a refrigerator hermetic unit (motor & compressor in one unit). It was a freebe from a local used appliance store. I bolted it down to a piece of plywood & soldered a 1/4" flare fitting on the suction line. It works great, pulls 29" of vacuum in about 10 minutes or less. I have used it several times and have had excellent results.




Pump to force cleaning fluid through the system $20-$50 (may use compressed air to do the same thing).

O ring seal kit = $8.

R134a charging adapter = $13 ( I cut mine up to use it with the R12 gauge set that I have had for a long time).

Plastic tools to disconnect refrigerant lines - 1/2" & 5/8" = $4 each.

Flushing agent - Discount Auto Parts has some flushing solvent in a 1 gallon plastic bottle - try that first. Or use Mineral spirits = $4 a gallon, tetrachloroethylene =$5-$10 a gallon, takes 2 gallons of either one.

Miscellaneous hoses and fittings to adapt the flushing pump to the system, and the R134a adapter to the R12 gauge set = $15.

I did a R134a conversion on my 89GT, and used all stock parts. You will need to replace the dryer/receiver (about $75 if you get the one with the hose made as part of the unit), and should replace all of the rubber "O" ring seals as well. You will need to drain all of the oil out of the compressor and replace it with new R134a compatible oil.

Keep in mind that to fulfill the requirements of the EPA, you are required by law to recover any refrigerant that still remains in the system. How (or wither or not) you accomplish this is up to you. Connect the charging gauge hoses to the service ports on the A/C (red gauge = high pressure, blue gauge = low pressure) and open the valves on the gauges to dump the remaining refrigerant (if any) into your "freon recovery system", whatever it may be. Disconnect the charging gauges since you are finished with them until you are ready to fill the system with R134a. Next comes the nasty part – in order to get all the old oil out of the system, you will need to flush it with special flushing solvent, or mineral spirits (ok) or tetrachloroethylene (better, but may be hard to get). If you leave the old oil in place it will congeal and reduce the heat transfer in the condenser and evaporator (read that it won’t cool good) and possibly damage the compressor.

Disconnect the compressor and remove it from its mount to flush it with cleaning solvent. Pour about a cup of solvent into the suction port and turn the compressor center hub about 10 turns while shaking the compressor to move the solvent around inside the compressor sump. Drain the flushing solvent out and continue to turn the center hub by hand to force out any remaining solvent. Then fill it with oil: add about 6-8 oz of the new oil to the compressor large suction fitting. Turn the compressor center hub about 20 turns as you turn the compressor face up and face down to distribute the new oil inside the compressor. Catch and replace any oil that comes out of the compressor.

Connect the pump (I had an electric sump pump I bought for $20) to the hose from the high-pressure side of the compressor. Alternately, you could use compressed air to force the cleaning fluid through the system. I didn’t like to do this since compressed air has lots of moisture in it, which is death to A/C systems. Pump the cleaning fluid through the system and let it come out the hose that was attached to the old dryer/receiver. I used 2 gallons of mineral spirits and pumped it all through the condenser and evaporator. The expansion valve is located near the firewall in the high-pressure line of the evaporator, and may cause the cleaning fluid to trickle through the lines at a very slow pace. You may want to pump cleaning fluid through the evaporator and condenser separately to speed up the process.

Next comes the changing of all the old "O" rings so that the chances for leaks is minimized. Use the plastic connector tools to separate the lines, place the extended collar part of the tool so that it faces the large part of the connector and push inwards: this expands the spring so that you can pull the tube apart. You may need a helper to push on the tool while you pull on the tubes to separate them. Install the new "O" rings: be sure to coat them with new oil when you put them in. Install the new dryer/receiver, R134a service port adapter, compressor, add about more 4oz of oil to high pressure line and tighten up all the lines. Close the hood, start the engine, let everything get warm under the hood, but don’t add the R134a or turn the A/C on. Connect the charging gauge hoses to the service ports on the A/C (red gauge = high pressure, blue gauge = low pressure) and open both valves, then connect the center hose to the vacuum pump. The purpose of this exercise is to heat up the system so that when you vacuum it all down (yes, you will need a vacuum pump- mine is an old refrigerator compressor), that all the air, vapor and moisture from the cleaning fluid vaporizes and is removed from the system. Vacuum it down for about 30 minutes, this should give you about 28" of vacuum or more inside the A/C system. I have a vacuum gauge "T" connected into the vacuum pump line so that I can accurately watch the vacuuming process. This is a good time to take a soda and sandwich break since it doesn’t go faster if you watch it.

Install the R134a service fittings on the system: the red goes on the high side and the blue on the low side. This will help others identify that a R134a conversion has been done on the system.

Remove the electrical connector from the dryer/receiver and jumper the two connections inside the wiring harness side of the connector together: this allows the compressor to engage in spite of low pressure/no gas in the system. Close both charging gauge valves, and then disconnect the center hose of the charging gauges from the vacuum pump and connect it to the R134a can tapper. Put the R134a can in the can tapper and screw it down with the can tapper valve closed, then open the valve. Loosen the hose at the center connection of the charging gauge set until the R134a squirts out: this purges the line of air and moisture. The refrigerant is added through the low pressure side of the system, so open the low pressure gauge valve to add the R134a. Start the car and take note of the idle speed, then set the idle speed up to about 1200-1500 rpm, and turn the A/C on inside and set the fan speed on high. Watch for the pressure on the low side to drop off as you are filling, and the R134a can will get warm and stay warm. This tells you the current can is empty and needs to be changed for a fresh one. Before you disconnect the can, be sure to close the valve on the R134a can tapper.

Watch the high side pressure on the charging gages and regulate the adding of gas to keep the high side pressure under 350 psi. You will probably need a fan in front of the car to keep the readings below 350 psi. I had to put the R134a can in hot water while I was charging the system with it, or else the can got so cold that it quit flowing. Use caution when you do this so that you don’t get water in the charging adapter when you change the cans. When you have added the 2 cans of gas, the high side will read about 250-300 psi and low side about 28-38 psi. Turn the idle speed back to where it was, turn the A/C off, disconnect the charging gauges, and re-install all the caps on the service ports. Remove the jumper from the low pressure switch harness and plug it back on the switch connectors. Then put the R134a Service Sticker on, secure all the loose wiring on the system and you are done. I hope it cools good, mine doesn’t get quite as cold as it used to driving around town.

The above technical note is for informational purposes only, and the end user is responsible for any damages or injury. The end user bears all responsibility for proper recovery/disposal of any refrigerant.

I have an EPA 609 MVAC certification. And yes, you can shortcut the process, but there are negative factors if you do. Sooner or later, something will cease to function like it should. Shoddy work is a time bomb ticking away, waiting to explode.
 
You must log in or register to reply here.

Similar threads

L
A/C doesn't work after long drive
  • lking78
  • Jun 23, 2026
  • SVT Tech Forum
Replies
1
Views
188
SVT Tech Forum Jun 30, 2026
Noobz347
B
Help! Fox with idle issues
  • bbarton
  • Sep 11, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
322
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 12, 2026
AeroCoupe
P
Fuel New Eldebrock 1406 problems 1985 GT 5.0
  • Paddyman
  • Oct 22, 2026
  • Fox 5.0 Mustang Tech
Replies
4
Views
184
Fox 5.0 Mustang Tech Nov 2, 2026
manicmechanic007
Engine A/C QUESTION
  • Mindseye007
  • Jun 5, 2025
  • Fox 5.0 Mustang Tech
  • 2 3 4
Replies
60
Views
3K
Fox 5.0 Mustang Tech Jun 22, 2026
nicholase
D
Loud noise(s) from Engine Bay
  • DuluthFoxbody
  • Oct 25, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
14
Views
402
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Nov 5, 2026
AeroCoupe
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?