Air bag light flashes

L

larbec7

New Member

May 28, 2007

25

0

0

May 28, 2007

#1

• May 28, 2007

• #1

I have a 1994 Stang 5.0 that i hust bought my son and the airbag light stays on. I checked a chart for a 93 model and it is giving a flash code of a 52. I will assume that the 93 is the same as a 94 unless someone corrects me.

How do I repair this and where is it?

52 | Backup power supply fault | R |


Thanks

 

C

chuck943

New Member

Oct 26, 2002

262

0

0

north carolina

May 28, 2007

#2

• May 28, 2007

• #2

Gray connector behind glove box on left side with 2 wires in connector T/R and BLK.
Cycle the ignition switch to OFF and then to RUN.
Observe air bag indicator prove-out (six ± two seconds) followed by diagnostic trouble code (52-85) flashing completely one time.
Locate the Diagnostic "Trouble Code Clear" Connector located underneath the glove compartment (06010) containing Circuits 631 (T/R) and 57 (BK).
Use a jumper wire to short Circuit 631 (T/R) to Circuit 57 (BK) or to another good ground. This short must be made after the diagnostic trouble code flashes completely one time, but before the warning light stays on continuously.
Hold short until air bag diagnostic monitor tone sounds (approximately five seconds).
Release short on Circuit 631 (T/R) to Circuit 57 (BK). This short must be released within 25 seconds after the diagnostic monitor tone sounds.
Diagnostic trouble code is now cleared from NVRAM. Next highest priority diagnostic trouble code stored in NVRAM (if one exists) will begin flashing

 

L

larbec7

New Member

May 28, 2007

25

0

0

May 28, 2007

#3

• May 28, 2007

• #3

Thanks

I will try this tomorrow, too late now

Thanks a bunch!!!

 

BlownFiveLiter

have car, will race....wait, it doesn't run

15 Year Member

Nov 29, 1999

3,133

18

108

Chicagoland

May 29, 2007

#4

• May 29, 2007

• #4

This site will help with your airbag codes.

 

L

larbec7

New Member

May 28, 2007

25

0

0

May 29, 2007

#5

• May 29, 2007

• #5

What is T/R ? I know BK = Black right??? Are these labeled like this??

If I do this, will my airbag come flying out?

Thanks for the help

 

C

chuck943

New Member

Oct 26, 2002

262

0

0

north carolina

May 29, 2007

#6

• May 29, 2007

• #6

Tan/Red .
Code 52 is from low voltage to module. Doing the process I described is to clear that code. If nothing else is wrong then you are done if something is wrong then it should flash another code.

 

P

phillipstheman1

New Member

Mar 14, 2007

37

0

0

May 29, 2007

#7

• May 29, 2007

• #7

whos doesn't every mustang ive been in does seems like

 

L

larbec7

New Member

May 28, 2007

25

0

0

May 29, 2007

#8

• May 29, 2007

• #8

I took the glove box out and I can see all the wires and connectors. There is not a two wire connector. On the left is a four wire with (Red, Blue, Black and a whiteish color looks ) and the only grey connector has about 6 wires that llok to be number 24 awg.

HELP!

 

C

chuck943

New Member

Oct 26, 2002

262

0

0

north carolina

May 29, 2007

#9

• May 29, 2007

• #9

sometimes its taped up in the harness so its hard to see. but its in that area,look from center brace over to left side of glove box

 

9

94v6GT

New Member

May 13, 2006

141

0

0

May 30, 2007

#10

• May 30, 2007

• #10

you dont have to take the glove box out. mine was taped to other wires UNDER the glove box.