Anyone with MSD 2 step launch control! I need help!

hollywoodstang · Dec 3, 2008

I have MSD Digital 6 and i am trying to hook up this 2-step

I know it needs 12volt power source applied and all, but the question is How/Where did you guys mount the switch? I want to see some pictures if you guys have any for the reference.

I have not be able to do this for a long time and i finally want to use this feature.

My car is 5 speed. I was trying to think where to put the switch and what method.

when i put the gear in 1st then i launch, So do i have to turn the switch off quick and slam in to 2nd? That seems like a lot of work...

I have no idea. Help me. Thanks

revhead347 · Dec 3, 2008

I made a switch enclosed in a small project box that I screwed down under the shift knob. Unfortunately I took it out to do some work, and I totally forgot where I put it. I'm looking for a normally closed relay to disable the nitrous when I'm on the launch rev limiter.

Kurt

hollywoodstang · Dec 4, 2008

Anyone else? Come on! I know some people are using this feature...

revhead347 · Dec 4, 2008

I don't think many people use that feature honestly. It doesn't help much. Even when I had it installed I didn't use it that much.

Kurt

Stanger007 · Dec 5, 2008

I've dyno'd quite a few cars with various setups. Last nite there was a car with a push button switch on a cord that could be tucked out the way when not in use, nice for a driver.

My favorite are the buttons on the shifters, transbrake style. We rewired the car last nite into a new shifter and removed the button on a cord in favor of this style setup.

Wes

hollywoodstang · Dec 5, 2008

Cool. Which wire did you use as 12v source? Thanks.

Redsnk95 · Dec 7, 2008

I would use a shifter handle from astro performance Astroperformance.com - Your Manual Drivetrain Specialist

It has a push button on top of the shifter. You will use that button to make the contact between the ignition box and your 12v source. You can just tap into a 12v key hot source in the fuse panel under the dash on the driver's side. It is a basic setup. You'll just let off the button when you let off the clutch pedal.

moostangvert · Dec 8, 2008

Redsnk95 said:
I would use a shifter handle from astro performance Astroperformance.com - Your Manual Drivetrain Specialist

It has a push button on top of the shifter. You will use that button to make the contact between the ignition box and your 12v source. You can just tap into a 12v key hot source in the fuse panel under the dash on the driver's side. It is a basic setup. You'll just let off the button when you let off the clutch pedal.

thanks for the link, i just bought one! btw, i see you post on outlaw

Charlie Allen · Dec 9, 2008

Mount the button under the clutch pedal on the floor and mount a micro switch on the trans that is only activated when the shifter is in first gear.

hollywoodstang · Dec 10, 2008

Charlie Allen said:
Mount the button under the clutch pedal on the floor and mount a micro switch on the trans that is only activated when the shifter is in first gear.

You got a pic of this?! and do you have to drill anything? urgh... here we go again...

Anyone with MSD 2 step launch control! I need help!

hollywoodstang

Active Member

revhead347

Apparently my ex-husband made that mistake.

hollywoodstang

Active Member

revhead347

Apparently my ex-husband made that mistake.

Stanger007

hollywoodstang

Active Member

Redsnk95

moostangvert

New Member

Charlie Allen

hollywoodstang

Active Member

Similar threads

Anyone with MSD 2 step launch control! I need help!

Active Member

Apparently my ex-husband made that mistake.

Active Member

Apparently my ex-husband made that mistake.

Active Member

New Member

Active Member

Similar threads

Privacy & Transparency

Privacy & Transparency