back to the trans again

whtnotch

New Member
Jan 8, 2007
123
0
0
Chicago
As I posted before I'v had issues with the trans (TKO 600) it turned out to be the flywheel was balanced wrong so I then corrected the problem with the a 50oz ford racing piece it seamed fine,but now heres the complication I go to take off in first I have some "?trans/clutch/throw out bearing?" related problem where the car hesitates and shakes on a dead take off and forget about reversing into garage(you hear grinding and all kinds of ***** comming from underneath when in reverse).I can hear the throw out bearing I let off clutch and can hear it wineing/hissing and once i push in it goes away. Can this be the problem?(throw out bearing)?or is the clutch not adjusted properly?Would like to know a.s.a.p. so I can know if i should move on to the 1st and reverse on trans failing so I still have warantee on it. Anyone please help me out i'm kinda screwed trans been in and out a few times now and i'm willing to do it once more.(Ha like i got choice)All problems happen durring clutch ingagement.I'm almost sure its in the bellhousing.
It's a spec stage 1 clutch if it helps to know.I will provide you with any other info you need to solve this mystery.If your in Chicago and you know what your talking about ill buy you a couple 24 cases.I will not go to the perf shop on this.

thank you all alot. your time and is greatly appreciated

Kevin
 
As I posted before I'v had issues with the trans (TKO 600) it turned out to be the flywheel was balanced wrong so I then corrected the problem with the a 50oz ford racing piece it seamed fine,but now heres the complication I go to take off in first I have some "?trans/clutch/throw out bearing?" related problem where the car hesitates and shakes on a dead take off and forget about reversing into garage(you hear grinding and all kinds of ***** comming from underneath when in reverse).I can hear the throw out bearing I let off clutch and can hear it wineing/hissing and once i push in it goes away. Can this be the problem?(throw out bearing)?or is the clutch not adjusted properly?Would like to know a.s.a.p. so I can know if i should move on to the 1st and reverse on trans failing so I still have warantee on it. Anyone please help me out i'm kinda screwed trans been in and out a few times now and i'm willing to do it once more.(Ha like i got choice)All problems happen durring clutch ingagement.I'm almost sure its in the bellhousing.
It's a spec stage 1 clutch if it helps to know.I will provide you with any other info you need to solve this mystery.If your in Chicago and you know what your talking about ill buy you a couple 24 cases.I will not go to the perf shop on this.

thank you all alot. your time and is greatly appreciated

Kevin


clutch and tranny noises are kinda hard to diagnose without just tearing the whole thing down .....
 
Just tore it down again...replaced the throw out bearing and threw it back in.Is the throw out bearing suppose to be making noise wit the clutch ingauged(in neutral)I know thats the sign of bad throw out bearing,but I just replaced a new one with another new one and it still making noise?.Car still making "grinding/chattering" on take off in 1st gear and horrably in reverse(sound like car wana fall apart in reverse) I dono what to do I wana run this car into wall:(
Somone please help.Anyone have this problem?I'm willing to break it down again if it will make it work mabey i'm just gana change the clutch I heard nothing but bad about SPEC Clutches,but my brother never had an issue in his Notch.Is the trow out bearing always suppose to be spinning?I can see it thru the Fork hole in bellhousing and its always spinning.i can provide any information needed i just need more opinions
 
Do you have the throw out bearing on the fork the right way. If you dontit will make that noise. The vibration your feeling is probably because of the throw out bearing or fork. Do you have the bearing behind the metal tabs on the fork. If not do it. Aslo inspect the pivot ball for the fork and the fork itself. That pivot ball will wear flat spots on it. Let me know if this helps. Good luck. I deal with trannys for a living.Doing it for 12 years
 
problem still remains...fork/bearing R A O.K. I broke it down 6 timez already seams to be getting better i got 85 miles on it so far,but still have that issue.If i'm rolling its much less violent of a take off almost nothing at all ,but off a dead start and im not focusing all on the clutch theres a problem.I drove car with my head under car and i can hear slight grinding on take off all other gears are fine tho its just on take off...Is it breaking in? Is it just breaking in or somthing its a steel flywheel so is it just longer to make its "groves" in the mating surface?Do you think its the pressure plate?like said before I ran the car around the block with a 28.5oz flywheel and i needed a 50oz could that of damaged it?

Kevin

P.S Help