• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

battery

  • Thread starter Thread starter mustangsally93
  • Start date Start date Apr 10, 2006

mustangsally93

New Member
Sep 26, 2005
281
0
0
Omaha,NE
Apr 10, 2006
#1
  • Apr 10, 2006
  • #1
1.)
Well first I need a pic of a 5.0s starter relay off a 90-93. When I put all the stuff back on the relay, the starter bumps when you put the battery cables on. So I need to see what I did wrong
2.)
I'm going to put my battery box in my hatch,( in the spare tire hole) so I need to know where to run the power cable and where should I hook the ground too. Also well this battery box work right?
Or should I go with a better one?

http://www.jegs.com/webapp/wcs/stor...atalogId=10002&storeId=10001&categoryId=26659
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Apr 10, 2006
#2
  • Apr 10, 2006
  • #2
The starter in the 93 is usually the mini starter, which is wired differently than the
86-90 model cars.
Here's the Autozone diagram for 91-93 5.0 Mustangs.



Rear mounted battery ground wiring. Follow this plan and
you will have zero ground problems.


One 1 gauge or 1/0 gauge wire from battery negative post
to a clean shiny spot on the chassis near the battery. Use
a 5/16” bolt and bolt it down to make the rear ground.
Use a 1 gauge or 1/0 gauge wire from the rear ground
bolt to a clean shiny spot on the block.

One 4 gauge wire from the block where you connected
the battery ground wire to the chassis ground where the
battery was mounted up front. Use a 5/16” bolt and bolt
down the 4 gauge engine to chassis ground, make sure
that it the metal around the bolt is clean & shiny. This
is the alternator power ground.

The computer has a dedicated power ground wire with
a cylindrical quick connect (about 2 ½”long by 1” diameter.
It comes out of the wiring harness near the ignition coil &
starter solenoid (or relay). Be sure to bolt it to the chassis
ground in the same place as you bolted the alternator power
ground. This is an absolute don’t overlook it item for EFI cars

Picture courtesy of timewarped1972




Crimp or even better, solder the lugs on the all the wire.
The local auto stereo shop will have them if the auto parts
store doesn't. Use some heat shrink tubing to cover the lugs
and make things look nice.

For a battery cut off switch, see http://www.moroso.com/catalog/categorydisplay.asp?catcode=42225
is the switch http://www.moroso.com/catalog/images/74102_inst.pdf is the installation instructions.
Use the super duty switch and the following tech note to wire it and you will
be good to go.

Use the Moroso plan for the alternator wiring and you risk a fire. The 10
gauge wire they recommend is even less adequate that the stock Mustang
wiring.

There is a solution, but it will require about 40' of 18 gauge green wire.

Wire the battery to the two 1/4" posts as shown in the diagram.

The alternator requires a different approach. On the small alternator plug
there is a green wire. It is the sense lead that turns the regulator on when
the ignition switch is in the run position. Cut the green wire and solder the 40'
of green wire between the two pieces. Use some heat shrink to cover the
splices. See http://fordfuelinjection.com/?p=7 for some excellent
help on soldering & using heat shrink tubing.

Run the green wire back to the Moroso switch and cut off the excess wire.
Try to run the green wire inside the car and protect it from getting cut or
chaffed. Crimp a 18 gauge ring terminal (red is 18 gauge color code for the crimp
on terminals) on each wire. Bolt one ring terminal to each of the 3/16" studs.
Do not add the jumper between the 1/4" stud and the 3/16" stud as shown it the
Moroso diagram.

How it works:
The green wire is the ignition on sense feed to the regulator. It supplies power
to the regulator when the ignition switch is in the run position. Turn the
Moroso switch to off, and the sense voltage goes away, the voltage
regulator shuts off and the alternator quits making power.

See the following website for some help from Tmoss (diagram designer) &
Stang&2Birds (website host) for help on 88-90 wiring and lots more…

http://www.veryuseful.com/mustang/tech/engine/images/IgnitionSwitchWiring.gif

http://www.veryuseful.com/mustang/tech/engine/images/fuel-alt-links-ign-ac.gif

http://www.veryuseful.com/mustang/tech/engine/images/88-91eecPinout.gif

Diagram courtesy of Tmoss and Stang&2birds.
 
M

Mike92GT

Founding Member
Jan 23, 2002
583
0
0
Florida
Apr 10, 2006
#3
  • Apr 10, 2006
  • #3
Here's another picture, the big cable runs back to my battery
 

Attachments

  • IM0000001.webp
    53.7 KB · Views: 129
You must log in or register to reply here.

Similar threads

S
92 5.0 almost starts
  • Steverino
  • Sep 23, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
5
Views
278
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 25, 2026
General karthief
R
Electrical Trunk Mount Battery and Cut Off Switch- Need Help
  • Rcdgl
  • Nov 20, 2024
  • Fox 5.0 Mustang Tech
Replies
1
Views
399
Fox 5.0 Mustang Tech Nov 20, 2024
nickyb
What's your tow rig?
  • LILCBRA
  • May 31, 2026
  • Other Auto Tech
Replies
9
Views
513
Other Auto Tech Oct 23, 2026
JH96GT
Resolved 93 Mustang 5.0 - Cranks but does not start
  • dan50
  • Jul 18, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
491
Fox 5.0 Mustang Tech Jul 18, 2026
dan50
A
Resolved Fuel Pump issue - test port jumped comes on (87 LX)
  • afjLX
  • Nov 16, 2024
  • Fox 5.0 Mustang Tech
  • 2
Replies
33
Views
3K
Fox 5.0 Mustang Tech Nov 26, 2024
afjLX
A
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?