• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

BBK Throttle Body Problems

  • Thread starter Thread starter savegoodautonfg
  • Start date Start date Mar 21, 2006
S

savegoodautonfg

New Member
May 11, 2005
1,085
0
0
Mar 21, 2006
#1
  • Mar 21, 2006
  • #1
Well 2 days ago I installed my new 70mm BBK Throttle Body and EGR Spacer. Now, when i go to drive and start my car it is running like crap. Lets start with loud noise like a vacuum leak and just alot of other noises also. I brought it to a close friend that is a mechanic and he sprayed carb cleaner around the egr spacer and the throttle body and the engine sounded the way it sounded before i install the new throttle body. He told me to get new gaskets and put them on. Now my question is did i put the gaskets on the wrong way and if so how are you suppose to put them on?

Also, I took out the throttle body today and the gaskets are coming tommorow so ill put them back on but when i took it off today the gasket from the egr spacer to the manifold one side was ripped?

Please help..

Don't know what to do.
 

lxwants12's

New Member
Sep 22, 2004
506
0
0
Mar 21, 2006
#2
  • Mar 21, 2006
  • #2
you must have put them on wrong i think the only problem there is the ripped gaskets...if you wanna take an extra precaution put some silicone there too....dont over tighten the nuts for the tb either remember its aluminum...tighten each one a little at a time...
 
S

savegoodautonfg

New Member
May 11, 2005
1,085
0
0
Mar 21, 2006
#3
  • Mar 21, 2006
  • #3
lxwants12's said:
you must have put them on wrong i think the only problem there is the ripped gaskets...if you wanna take an extra precaution put some silicone there too....dont over tighten the nuts for the tb either remember its aluminum...tighten each one a little at a time...
Click to expand...

Hey thanks for the reply,

First of all how are you suppose to put them on?

And second of all, Where do i put the silicone?

Also, how tight should i tighten them?
 
B

BaXTeR3221

Member
Jan 12, 2004
917
0
16
Orange County, NY
Mar 21, 2006
#4
  • Mar 21, 2006
  • #4
I would deffinetly use silicone on there. I used it on my tb when i had a similar problem and it went away nicely.
 

lxwants12's

New Member
Sep 22, 2004
506
0
0
Mar 21, 2006
#5
  • Mar 21, 2006
  • #5
clean the areas of the gasket good...i think theres only one way to put them gaskets on they are cut to fit a certail way...anywayz put the 1st gaskets on the plenum then silicone on top that gasket...then put the spacer on....do the same for the next gasket then when u tighten the bolts tighten one at a time little by little..thik of them as a valve cover gaskets you dont wanna overtighten and rip the gasket..but snug enough not to move...no need to be a muscleman when tightening them
 
S

savegoodautonfg

New Member
May 11, 2005
1,085
0
0
Mar 21, 2006
#6
  • Mar 21, 2006
  • #6
lxwants12's said:
anywayz put the 1st gaskets on the plenum then silicone on top that gasket...then put the spacer on
Click to expand...

BTW, u mean on top of the black part of the gasket and then put the spacer on so they are sticking together almost.
 

lxwants12's

New Member
Sep 22, 2004
506
0
0
Mar 21, 2006
#7
  • Mar 21, 2006
  • #7
on top meaning of the face that the tb will be touching..im not sure of colors or anything been awhile since i have seen one...or you can clean up the tb really good and put the silicone on the backside of the tb...(the side thats touching the gasket....so when you tighten the nuts on the tb the silicone will squeeze outta the sides a little bit
 
S

savegoodautonfg

New Member
May 11, 2005
1,085
0
0
Mar 21, 2006
#8
  • Mar 21, 2006
  • #8
Thanks again for all your help. I'll let you know what happens.
 

lxwants12's

New Member
Sep 22, 2004
506
0
0
Mar 21, 2006
#9
  • Mar 21, 2006
  • #9
no prob hope it works out for ya
 
You must log in or register to reply here.

Similar threads

Engine Sick of stock TB and EGR spacer...
  • 91GTstroked
  • Dec 15, 2024
  • Fox 5.0 Mustang Tech
Replies
6
Views
828
Fox 5.0 Mustang Tech Dec 19, 2024
General karthief
M
Engine Unexplainable Exhaust Pop and Gurgle
  • Mrnissen122
  • Feb 14, 2026
  • Fox 5.0 Mustang Tech
Replies
12
Views
851
Fox 5.0 Mustang Tech Feb 18, 2026
Noobz347
J
Engine 4.6 Running rough at half throttle
  • jake411
  • Aug 3, 2026
  • SN95 4.6L Mustang Tech
Replies
5
Views
319
SN95 4.6L Mustang Tech Oct 20, 2026
DangStitches
D
2
Running very very rich
  • 2esoteric
  • Oct 31, 2025
  • Fox 5.0 Mustang Tech
Replies
4
Views
470
Fox 5.0 Mustang Tech Oct 31, 2025
Noobz347
D
sad day
  • davecobra2
  • Jul 13, 2026
  • What is it Worth?!?!?
Replies
2
Views
312
What is it Worth?!?!? Jul 22, 2026
davecobra2
D
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?