Body Work and POR-15

geostang351 · Apr 8, 2006

I have done the cowl on my brothers 66 but the metal now goes from rust in the middle to new metal at the ballons. The welded seam needs to be worked with bondo to form a semi smooth line. I plan on putting POR-15 at this entire area. My question is this: Do I do the bondo first on the raw metal or do the POR first, then the bondo filler?

shelbe67 · Apr 8, 2006

is it rusty?

Platonic Solid · Apr 8, 2006

Por15 first. You want the Por15 to do what it's designed to do - Bond to and Stop current rust and prevent future rust. You will need to clean (w/marine clean) and acid etch (w/metal ready) all metal surfaces prior to putting Por15 on anyway. Acid etching stops current rust and gives the Por15 something to bite into on new metal work. Here's a write-up on how I did my window channel: (I highly recommend their fiberglass cloth as it is stiff and easy to cut and work with - unlike the stuff you get at the auto parts store. I also like their Epoxy Putty, which gives you a longer working window, and it's easier to make small quantities, than Bondo)

73channelrepair

73rearwindow

and

The Trunk Tail Panel

Platonic Solid · Apr 8, 2006

Go here: POR-15 RUST PREVENTIVE PAINT. Click and read the Por-15 Direction links.

geostang351 · Apr 8, 2006

Thanks Plutonic. I have looked at POR and it seems it is a little more involved then the rust bullet product. Seems to work the same with less prep. Your thoughts;

http://rustbullet.com/

Platonic Solid · Apr 9, 2006

They make some big claims, but I have no personal experience with it. I don't have time to read their whole site right now, but I might consider testing it in the future. Por15 is quite labor intensive.

RMODEL65 · Apr 9, 2006

the stuff is awesome itll stich to anything we had it in a clear gallon water jug the smooth kind (unscuffed!) the plastic jug broke it tried like crazy to break the paint

Platonic Solid · Apr 9, 2006

OK, I spent some time on Rust Bullet's site and it leaves me with one major test discrediting question: Why was the POR-15 test panel, used throughout the comparison tests, topcoated with a NAPA paint rather than POR-15's own Chassis Coat?

Also, the tests would have better illustrated typical end use had the coatings been applied to rusty metal test samples.

Red5oh · Apr 9, 2006

I have used the rust bullet and I feel it is equal with POR15. I liked the ability to put it on w/o a topcoat. I used the por15 paste in one area and it was just as 'hard' when cured. I have used the rustbullet through most of my project though it was not very rusted.

I was impressed by how hard it was when cured and put it on as a preventative measure. When I was under the car, it had that red primer on it from the factory and we all know that stuff absorbs water over time. I spent the time to remove all of that and apply rust bullet. I believe it will be time well spent and since my car is not a restore, it doesnt really matter.

You can see pictures on my cardomain site and ask all the questions you want.

Mark

Platonic Solid · Apr 9, 2006

I’m sure Rust Bullet is a fine product. I just get annoyed when companies push the envelope of truth. Rust Bullet claims to be a one-step process and states POR-15 is a four-step process. Then they proceed to count degreasing as one of POR-15’s steps, conveniently ignoring their own instructions, which state: “All surfaces must be free of loose rust, moisture, dirt, mildew, oily substances, wax, loose paint, and loose particles.”

Red5oh · Apr 9, 2006

True, and I am not claiming they are better. The tests prove though that POR15 and Rustbullet are about equal. It would be a tough choice between the two. I really dont think you could go wrong with either.

Problem really is... everyone does it. They publish only the positive points of their product over the competition...

smitzer · Apr 9, 2006

platonic solid: would your channel repair be possible with this rust bullet product too? Could regular fiberglass mat be used? and are there other brands of epoxy putty out there? Newbie questions but I am not that familar with these products.

smitzer

Platonic Solid · Apr 9, 2006

smitzer, I really can’t comment on products and combinations that I haven’t tried. A good site to do research on is autobodystore.com. I’d guess Eastwoodco.com probably has similar epoxy putty type supplies.

geostang351 · Apr 9, 2006

Good stuff! Thanks

Body Work and POR-15

geostang351

Member

shelbe67

Member

Platonic Solid

Platonic Solid

geostang351

Member

Platonic Solid

RMODEL65

Member

Platonic Solid

Red5oh

Member

Platonic Solid

Red5oh

Member

smitzer

Platonic Solid

geostang351

Member

Similar threads

Body Work and POR-15

Member

Member

Member

Member

Member

Member

Member

Similar threads

Privacy & Transparency

Privacy & Transparency