BOLT THREAD REFERENCE!

srtthis · Mar 3, 2010

since there has been plenty of talk... and no doing it...

intake manifold
5/16-18 x 2.5
valve cover
1/4-20 x 1
Crank pulley
3/8-16 x 1
Plugging Smog Hole (thermactor plug) 5/8-11
speed sensor clamp
1/4-20 x 3/4
Tps sensor screws
M4 x 0.7 pitch x 25mm length
intake plaque
8-32x1/2" taper seat machine screw
For those who need to plug their low oil level sensor hole
Oil plug M20 1.5 thread pitch
Edelbrock performer and typhoon upper plenum cover-
1/4x1 machine cap screws are a direct fit
Edelbrock performer and typhoon upper to lower studs-
5/16x1-3/8 carb studs.
Thermostat housing
5/16-18 x 1 3/4" for top left bolt
5/16-18 x 1 1/4" for bottom right bolt
Both bolts use split lock washers.

Battery hold down bolt
6mm x 1.0 x 55mm

87+ Wiper motor screw: 1.25" long blunt sheet metal screws. 1/4"-14 thread

Rear Shock 12mm x 1.75 x 70mm or you can use a 1/2" x 1.50" long bolt.

Quad shock axle housing mounting bolts(12mm x 1.75 x 70mm)

add what you have... we get a good amount i will put it in excel and put the torques and such also!

mods please sticky!

Mustang5L5 · Mar 3, 2010

Stuck

I must add, please only post up info if you are 100% sure as to what the bolt size is. Don't guess please....double check if necessary.

ReefBlueHatch · Mar 3, 2010

From 4G-KDMP,
Plugging Smog Hole (thermactor plug) 5/8-11

BTW, thanks for starting this thread!

srtthis · Mar 3, 2010

ReefBlueHatch said:
From 4G-KDMP,
Plugging Smog Hole (thermactor plug) 5/8-11

BTW, thanks for starting this thread!

added as a 5/8-11 set screw since this is a common useage

Celeb · Mar 20, 2010

For those who need to plug their low oil level sensor hole

Oil plug M20 1.5 thread pitch

stykthyn · Mar 25, 2010

Edelbrock performer and typhoon upper plenum cover- 1/4x1 machine cap screws are a direct fit
Edelbrock performer and typhoon upper to lower studs- 5/16x1-3/8 carb studs.

rd · Apr 1, 2010

79 outer tie rods 9/16 fine thread. Use a bottoming tap in the end and a longer Tbird rack and inner will fit a Stang.

Nutzy19 · Jul 3, 2010

stykthyn said:
Edelbrock performer and typhoon upper plenum cover- 1/4x1 machine cap screws are a direct fit
Edelbrock performer and typhoon upper to lower studs- 5/16x1-3/8 carb studs.

thats when you dont use the included spacer!!! Its more like 5/16X 2 1/2 studs for the Eddy intake

jrichker · Jul 8, 2010

Water pump bolt kits - See Totally Stainless for replacement stainless steel bolts. Last time I checked, they didn't have the studs. Nice folks, very into cars of all types. They have all kinds of stainless fasteners for almost every car. The prices are very reasonable, less the $10 for the water pump kit without the studs.

Water pump stud kit
The studs are a Motormite item available at your local Advance Auto Parts store.

Motormite Water Pump Stud Kits for Ford, Lincoln and Mercury cars and trucks w/3.8L, 4.6L, 5.0L, 5.8L.

Part Number: 23744

Mustang5L5 · Jul 31, 2010

Tps sensor screws

M4 x 0.7 pitch x 25mm length

srtthis · Aug 17, 2010

intake plaque

8-32x1/2" taper seat machine screw

dsinka01 · Aug 17, 2010

exhaust manifold bolts for 71' 351W 5/16 18" x 1 1/2 long
bellhouse to motor on a 71' 351W 7/16 14" x 2 1/2 long
trans mount from mount to crossmember m10 x 1.5x 20mm

mob · Sep 9, 2010

Got the water outlet bolt sizes thanks to a guy on Corral

5/16-18 x 1 3/4" for top left bolt
5/16-18 x 1 1/4" for bottom right bolt
Both bolts use split lock washers.

mob · Sep 13, 2010

Here guys I put these in a Google Docs file, hopefully we can get more coming in, I think this thread is a great idea. I'll keep updating it as I finish my build as I have either thrown away or misplaced most of my old bolts.

https://spreadsheets.google.com/ccc...EU1dTdqd1lESWFpLWVXYlE&hl=en&authkey=CLypir4N

jrichker · Oct 5, 2010

mob said:
Here guys I put these in a Google Docs file, hopefully we can get more coming in, I think this thread is a great idea. I'll keep updating it as I finish my build as I have either thrown away or misplaced most of my old bolts.

That's what zip-lock bags are for.... You can even stick a post-it note or scrap of paper inside the zip-lock bag and write on it what the bolts are for. If you are doing a long term project, this is the best way to keep track of the bolts and other small hardware items. Throw all the zip-lock bags in a 5 gallon bucket and it is easy to keep up with all the small parts.

giddyup306 · Dec 30, 2010

Great thread idea!

If any of you were like me and threw away your old K member before removing the bolts, here's the a arm bolt size.

m16x2.0x117.5. #N808476 S301

They're pretty hard to find...

http://www.palmerbolt.com/catalog.asp?prodid=596691&showprevnext=1

I called up QA1 to see if they had a kit or knew what size they were... they old me to use the old bolts. If they are anything like my K member bolts they were half rusted through and two of them snapped completely off when I went to remove them! Speaking of which I will post those bolt sizes as soon as I get my new ones.

4G-KDMP · Jan 29, 2011

fox body mustang quad shock mount into frame 12mm x 1.75 x 70mm

ReefBlueHatch · Apr 23, 2011

Lower control arm bolts: 12mm-1.75x100

90 lx convert · Jun 4, 2011

OK, question. B&M Hammer shifter. Stick thread size? I'm looking to change handles and need to make an adapter for the new handle as it doesn't come with the right adapter. What tap? Mike

Noobz347 · Nov 16, 2011

We need to figure out and post the bolt sizes for the whole accessory drive too.

BOLT THREAD REFERENCE!

srtthis

the guy doing it does every local racers rear end

Mustang5L5

That is…until I whipped out my Bissell

ReefBlueHatch

Active Member

srtthis

the guy doing it does every local racers rear end

Celeb

stykthyn

I want to measure mine. It doesn't look that tall.

rd

Nutzy19

Member

jrichker

StangNet's favorite TOOL

Mustang5L5

That is…until I whipped out my Bissell

srtthis

the guy doing it does every local racers rear end

dsinka01

Member

mob

the guy who hits on his mom

mob

the guy who hits on his mom

jrichker

StangNet's favorite TOOL

giddyup306

4G-KDMP

ReefBlueHatch

Active Member

90 lx convert

Stanger

Noobz347

Stangnet Facilities Maint Tech... Er... Janitor

Similar threads

BOLT THREAD REFERENCE!

the guy doing it does every local racers rear end

That is…until I whipped out my Bissell

Active Member

the guy doing it does every local racers rear end

I want to measure mine. It doesn't look that tall.

Member

StangNet's favorite TOOL

That is…until I whipped out my Bissell

the guy doing it does every local racers rear end

Member

the guy who hits on his mom

the guy who hits on his mom

StangNet's favorite TOOL

Active Member

Stanger

Stangnet Facilities Maint Tech... Er... Janitor

Similar threads

Privacy & Transparency

Privacy & Transparency