• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

brightest headlights available?

  • Thread starter Thread starter tommy_1812
  • Start date Start date Jan 6, 2006
  • 1
  • 2
Next
1 of 2 Next Last
T

tommy_1812

New Member
Dec 21, 2005
41
0
0
Kerrville, TX
Jan 6, 2006
#1
  • Jan 6, 2006
  • #1
I am wondering what the brightest available headlights are for my 1990 mustang. I would prefer something that has a very bright highbeam filament. I've heard that 80 to 100 watt bulbs can be found and installed. Would I need to get a relay for the headlights?

I am willing to use offroad highbeams if possible.

Too many people around here with their new vehicles and insanely bright high beams. Inconsiderate people who don't turn their high beams off at oncoming traffic has pushed me too far. I am looking for something that is potentially blinding, and only used when no cars are around, or at drivers who fail to switch to low beams when oncoming to me. That will make them think twice about being inconsiderate.

Any suggestions would be helpful.
 

Euphoric306

New Member
Apr 5, 2004
905
0
0
Jan 7, 2006
#2
  • Jan 7, 2006
  • #2
you may consider HID retrofits, which can be pricey, but offer the brightest light. only downside is there either is no high beam setting, or it's already bright enough not to need one


IMO, blinding drivers who are in turn blinding you doubles the safety risk of passing eachother, so be an idiot if you must, but don't get pissed when someone runs into your side of the road due to your bright beams
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Jan 7, 2006
#3
  • Jan 7, 2006
  • #3
I have the same issue, but still run stock wattage bulbs. Seems to me that Silverstars are about as good as you can do Bulb-wise.

You definately would want to upgrade the wiring and install relays for such wattage (the switchgear wont handle that many watts/amps).

Couple other things come to mind. Be careful - you could melt your plastic lens housings. Another means to help is with some killer driving lights. I rum some that are illuminate better than the headlights do, and the beam is lower so it should not distract oncoming drivers.

On a 2G alternator, I noticed that having relays on low beams, high beams, and fogs helped output a noticeable amount. It also saves switchgear and diminishes the amount of dimming at hot idle.

And a 3G noticeably increased the light output across the board by a LOT IMHO.

Good luck.
 
J

JRPony

New Member
Jun 10, 2005
83
0
0
Las Vegas, NV
Jan 7, 2006
#4
  • Jan 7, 2006
  • #4
tommy_1812 said:
That will make them think twice about being inconsiderate.
Click to expand...
I sincerely doubt that blinding them will make them think twice about "being inconsiderate". What is more likely to happen is that they will become temporarily blinded and crash into you. Then it is you who will be thinking twice about intentionally blinding oncoming traffic.
 

RacEoHolic330

I like to dress like a pretty girl
15 Year Member
Mar 4, 2003
4,014
1,698
203
Allentown, PA
Jan 7, 2006
#5
  • Jan 7, 2006
  • #5
I have a set of BMW hid projectors retrofitted into my car. I have both high and low beam function. The light output is rediculous. It was a total pain in the ass to do and costed around 400 dollars. Well worth it to me though when I'm driving through tiny little streets in the middle of the woods.
 

srothfuss

Last night I stabbed the same guy 7 times in a row
Oct 17, 2004
1,796
3
0
Woodward Ave.
Jan 7, 2006
#6
  • Jan 7, 2006
  • #6
Sliverstars are simple plug and play type of deal.

It's a good $40.00 to spend.
 

pb_paulie_b

Founding Member
May 19, 2001
894
0
0
Chaptico, Maryland
Jan 7, 2006
#7
  • Jan 7, 2006
  • #7
I hated people like that too, so I ran a hose from my water pump to the side of my car. Now when they do it I spray down their lane with antifreeze.
They are all dead now
 
S

superhuaman

New Member
Nov 8, 2004
907
0
0
Harrisburg, PA
Jan 7, 2006
#8
  • Jan 7, 2006
  • #8


I worked on this car one time that had the washer nozzles on the wiper arms, right? Well the passenger side tube was cracked, so that when you cleaned your windshield, the pedestrians on the sidewalk would run for cover.
 
P

PRO50SC

New Member
Dec 28, 2003
1,012
1
0
Olney, Maryland
Jan 7, 2006
#9
  • Jan 7, 2006
  • #9
Just toss a brick through their windsheild as they drive by!!!
 
P

PRO50SC

New Member
Dec 28, 2003
1,012
1
0
Olney, Maryland
Jan 7, 2006
#10
  • Jan 7, 2006
  • #10
Check with this guy. Not sure how much you want to spend but......

Here is what our kits look like....


Installation: simple plug and play installation takes less than 30 minutes. No cutting or splicing of wires. Go back to stock just as quickly.

Warranty: All kits include 1 year manufacturer warranty. Anything goes wrong with the kit, they replace the entire unit for free.

Fitment: I have HID kits for most all cars. Let me know which kind of vehicle you have and I will check to make sure we carry a kit for it. Most likely, we will have it. We carry 6000K (pure white color), 8000K (blueish/white color), and 10000K (pure blue color) kits.

Pricing: On my site the kits go for $325 shipped.
If you have any questions, please feel free to ask. Thank you. If would like to just go ahead with a purchase, Paypal accepted at: sales@shiftergaskets.com or call me:240 876 9705 or email me: sales@shiftergaskets.com to arrange a personal delivery. Thanks again!
__________________


www.stangmods.com
 
T

tommy_1812

New Member
Dec 21, 2005
41
0
0
Kerrville, TX
Jan 8, 2006
#11
  • Jan 8, 2006
  • #11
I've found a different solution to this issue. Everytime an oncoming car approaches on the highway, I turn my brights off to be considerate. The oncoming car has 2 choices. Most turn their brights off in turn. A few don't. I then turn my brights on and leave them on untill they turn them off (realizing their error at the last minute), or they leave them on and I keep my brights on the whole time.

Most are conscious about this and they turn the brights off right away. You can always tell their brights are on by looking at the intensity, coverage of their beam, and angle of it. There's a few cars who I won't be able to tell if they have their high beams on or not, if the light isn't bothering me, I will leave my low beams on.

The few who don't give a ****, obviously know they have their highs on, when other people flash them (I don't flash, I just flick my highs on untill they lower theirs), and they continue to leave them on. They'd rather see well at the expense of others.

For a $80 investment last month, I purchased a 3 million candle power Industrial spot light for my night job. I only had to use it once in my car so far last night. Someone in an Escalade or Navigator SUV had their brights on half a mile down the highway. I turned my brights off as we got closer as common courtesey. They didn't turn their brights off. The lights started getting to my eyes, and I flicked my brights on. Within a 1/4 mile, they had the nerve to flash their brights at me several dozen times, while leaving them on. The lights were really getting my eyes, so I grabbed my fully charged spotlight and got almost 10 seconds of shining this light at the driver.

As they drove by, I got a view at the driver and passenger (possibly some in the back), looked like 2 punk kids, driver was holding his hand by his face probably from the spotlight, they layed on the horn as we both passed, and they pulled over to the side of the road. I saw it was either a navigator or escalade. They pulled a hard U-turn and were swerving, obviously pissed. They were flashing their brights fast and furious as me and I dropped to 4th, got over a few hills and hooked right onto a street I knew, drove a few miles to another side of town.

Moral of all this? There are people who insist on driving with their brights on. If someone else has the nerve to try and take away that comfort of seeing really far ahead, they will flash their brights several times. This is not the first time that someones flashed me because I flashed my brights at their already high beams. It is the first time I got to give them a taste of their own medicine, and I didn't have to spend more than 40 bucks!

Any of you would probably do the same thing because high beams on these new luxery SUVs are insanely bright! I was seeing spots because of those aholes. Their low beams (the ones I saw for split second intervals) seemed to be much more pleasant.
 

Euphoric306

New Member
Apr 5, 2004
905
0
0
Jan 9, 2006
#12
  • Jan 9, 2006
  • #12
tommy_1812 said:
I've found a different solution to this issue. Everytime an oncoming car approaches on the highway, I turn my brights off to be considerate. The oncoming car has 2 choices. Most turn their brights off in turn. A few don't. I then turn my brights on and leave them on untill they turn them off (realizing their error at the last minute), or they leave them on and I keep my brights on the whole time.

Most are conscious about this and they turn the brights off right away. You can always tell their brights are on by looking at the intensity, coverage of their beam, and angle of it. There's a few cars who I won't be able to tell if they have their high beams on or not, if the light isn't bothering me, I will leave my low beams on.

The few who don't give a ****, obviously know they have their highs on, when other people flash them (I don't flash, I just flick my highs on untill they lower theirs), and they continue to leave them on. They'd rather see well at the expense of others.

For a $80 investment last month, I purchased a 3 million candle power Industrial spot light for my night job. I only had to use it once in my car so far last night. Someone in an Escalade or Navigator SUV had their brights on half a mile down the highway. I turned my brights off as we got closer as common courtesey. They didn't turn their brights off. The lights started getting to my eyes, and I flicked my brights on. Within a 1/4 mile, they had the nerve to flash their brights at me several dozen times, while leaving them on. The lights were really getting my eyes, so I grabbed my fully charged spotlight and got almost 10 seconds of shining this light at the driver.

As they drove by, I got a view at the driver and passenger (possibly some in the back), looked like 2 punk kids, driver was holding his hand by his face probably from the spotlight, they layed on the horn as we both passed, and they pulled over to the side of the road. I saw it was either a navigator or escalade. They pulled a hard U-turn and were swerving, obviously pissed. They were flashing their brights fast and furious as me and I dropped to 4th, got over a few hills and hooked right onto a street I knew, drove a few miles to another side of town.

Moral of all this? There are people who insist on driving with their brights on. If someone else has the nerve to try and take away that comfort of seeing really far ahead, they will flash their brights several times. This is not the first time that someones flashed me because I flashed my brights at their already high beams. It is the first time I got to give them a taste of their own medicine, and I didn't have to spend more than 40 bucks!

Any of you would probably do the same thing because high beams on these new luxery SUVs are insanely bright! I was seeing spots because of those aholes. Their low beams (the ones I saw for split second intervals) seemed to be much more pleasant.
Click to expand...

:Teh-Win:
 

DmnStr8

Member
Apr 16, 2005
0
0
16
NH
Jan 9, 2006
#13
  • Jan 9, 2006
  • #13
Nice, I had some punk kids flash one of those flashlights at my fiance and I as they passed us. Then the ****er leaned out the window to get us from in front while the driver braked hard. Dunno why, probably thought it was funny.

He was lucky that my girl calmed me down cause I had my 38 and I was getting ticked to say the least.

I did get his plate number though... was gonna turn it in but I think it will be even better to keep it in case i ever run into him again....

Moral of this story. You never know who has a gun, so don't you think it might be better to just take one. Let the *******s be *******s and not lower yourself by playing thier games.
 

Michael Yount

Mustang Master
Apr 10, 2002
9,039
6
79
Charlotte, NC
Jan 9, 2006
#14
  • Jan 9, 2006
  • #14
If you want to understand a bit more about lighting systems, I've found this site useful ... http://www.danielsternlighting.com/home.html

I upgraded my '4 eye' configuration with European Hella H1 and H4 lights, added relays and 10ga/12ga wiring to eliminate the drop from alternator to bulbs, and installed 80w/100w H4 bulbs, and 100w H1 bulbs. It is bright -- properly aimed they don't tick anyone off and I've got 0.00V drop between the alternator and the bulb that's furthest away.

Simply adding high wattage bulbs without upgrading the wiring and installing relays will generally fry fuses if not your wiring and light switches. Part of the reason for poor performance of stock systems is due to the voltage drop that occurs just getting current to the stock bulbs. Relatively small wiring runs from the source (alt/battery) inside the car to the switch and back out to the bulbs. It's not uncommon to lose 2-3 volts just getting to the bulb -- and that shows up as 30-50% reduction in lighting output. Relays/bigger gauge wiring helps a lot even if you don't upgrade bulbs. Be careful though -- I think y'all are dealing with plastic housings that have a limit as to how much heat they can take. Mine are all glass/steel - so I can turn the flame-throwers on.
 

Michael Yount

Mustang Master
Apr 10, 2002
9,039
6
79
Charlotte, NC
Jan 9, 2006
#15
  • Jan 9, 2006
  • #15
PRO50SC - what's the website address that the 'kit' info came from? There's an email address, but no web address.
 
B

blackcloud50

New Member
Mar 30, 2005
388
0
0
Jan 9, 2006
#16
  • Jan 9, 2006
  • #16
Michael Yount said:
Be careful though -- I think y'all are dealing with plastic housings that have a limit as to how much heat they can take. Mine are all glass/steel - so I can turn the flame-throwers on.
Click to expand...

Those plastic housings (atleast the Ultra Clear) from 50RESTO don't fair well to the added heat of the 80/100 9004 bulb as I verified in a previous post. It really sucks because the output was great from them. So I just stick with the Silverstars and harness upgrade which have a pretty decent output.
 

Shakerhood

20+ Year Stangneter
Oct 28, 2004
3,361
211
114
Ohio
Jan 10, 2006
#17
  • Jan 10, 2006
  • #17
blackcloud50 said:
Those plastic housings (atleast the Ultra Clear) from 50RESTO don't fair well to the added heat of the 80/100 9004 bulb as I verified in a previous post. It really sucks because the output was great from them. So I just stick with the Silverstars and harness upgrade which have a pretty decent output.
Click to expand...

If you have Silverstars that have the same rating as stock bulbs, why would a extra wiring harness be needed?
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Jan 10, 2006
#18
  • Jan 10, 2006
  • #18
Shaker, I think he upgraded the harness when he used the higher-drawing bulbs (80/100's). But since his lenses went south after that, he now just runs the Silverstars on the existing upgraded harness (the harness was not upgraded just for Silverstars).
 

Michael Yount

Mustang Master
Apr 10, 2002
9,039
6
79
Charlotte, NC
Jan 10, 2006
#19
  • Jan 10, 2006
  • #19
I believe you'll find that a harness upgrade with relays will do more for your lighting output than putting a set of Silverstars in with no harness upgrade. Take your voltmeter with the car idling and headlights on -- measure the voltage at the alterntor output; measure the voltage at the headlight bulb. The difference is the drop through the stock harness and it SIGNIFICANTLY impacts output - see the link in my post above for a great explanation of this.

However - the biggest problem with lighting on these cars (later model Volvos have the same issue) is the plastic lenses become cloudy/yellowed. And when they do, you can upgrade the harness and put big-watt bulbs in --- but the light can't penetrate that cloudy plastic lense. So if your lenses aren't "see-through-new" looking - don't bother with upgrading what's behind it.
 
9

93-331-29psi

Member
Jul 20, 2004
157
0
17
NE North Carolina
Jan 10, 2006
#20
  • Jan 10, 2006
  • #20
Michael Yount said:
I upgraded my '4 eye' configuration with European Hella H1 and H4 lights, added relays and 10ga/12ga wiring to eliminate the drop from alternator to bulbs, and installed 80w/100w H4 bulbs, and 100w H1 bulbs. It is bright -- properly aimed they don't tick anyone off and I've got 0.00V drop between the alternator and the bulb that's furthest away.
Click to expand...

I did this same upgrade with my 86 and the light output is nearly as good as my 2005 F250. I would recommend to anyone with a 4-eye car to do this upgrade.
 
  • 1
  • 2
Next
1 of 2 Next Last
You must log in or register to reply here.

Similar threads

1
Electrical Headlight harness trouble
  • 1985fox
  • Apr 14, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
484
Fox 5.0 Mustang Tech Apr 17, 2026
AeroCoupe
1
Electrical 1985 mustang gt Led conversion trouble
  • 1985fox
  • Jan 5, 2026
  • Fox 5.0 Mustang Tech
Replies
10
Views
848
Fox 5.0 Mustang Tech Jan 15, 2026
1985fox
1
K
2003 Mustang GT Convertible Headlight H/L Issue
  • krysber
  • Mar 20, 2025
  • SN95 4.6L Mustang Tech
Replies
1
Views
299
SN95 4.6L Mustang Tech Mar 21, 2025
85GTStangGuy
M
Headlights
  • Magnet86
  • May 19, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
1
Views
260
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 20, 2025
Blown88GT
P
Interior and Upholstery Door Speakers- found suggestion to go component, not coaxial
  • pindude80
  • Apr 21, 2025
  • Fox 5.0 Mustang Tech
Replies
13
Views
2K
Fox 5.0 Mustang Tech Apr 28, 2025
Mindseye007
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?