• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech

C&L Plenum

  • Thread starter Thread starter cronin49
  • Start date Start date Feb 27, 2004
C

cronin49

Banned
Aug 12, 2003
432
1
16
SC
Feb 27, 2004
#1
  • Feb 27, 2004
  • #1
Hey everyone, I just purchased the new C&L Intake Plenum and an Accufab 75MM throttle body. Will my computer adjust itself or am I looking at problems? I am currently using the Superchips Max Microtuner to retune my computer for my gear change, among other things. My Mods are in my signature. By the way, I got both parts from C&L direct for $407.00, shipped. That ain't too bad, is it? I saw the write-up in MM&FF and said what the heck, 12 HP for 400 bucks? I went for it. Thanks.
 

Beau

Founding Member
Jan 29, 2000
3,050
0
0
San Diego
Feb 27, 2004
#2
  • Feb 27, 2004
  • #2
you would have paid less if you had bought it from ronnie diaz..

www.rdmrdm.com


i have both, but i don't have a chip or anything, so what i did was disconnect the batter and hold the brake pedal down for a few seconds to drain all the electricity from the system. then i installed everything and reconnected the battery. in this way, the car's computer was re-set and so far i have had 0 problems.
 

bergs

Member
Jan 19, 2004
117
0
17
new jersey
Feb 27, 2004
#3
  • Feb 27, 2004
  • #3
i just put them on last night and it runs fine. i have done nothing to my computer. i can tell the difference with the plenum and TB, its pretty sweet. i got mine for 395 shipped from CL performance.
 

scalder

Member
Aug 1, 2003
375
0
16
Dallas/Plano TX
Feb 27, 2004
#4
  • Feb 27, 2004
  • #4
You'll be fine...enjoy!
 
C

cronin49

Banned
Aug 12, 2003
432
1
16
SC
Feb 27, 2004
#5
  • Feb 27, 2004
  • #5
plenum

scalder said:
You'll be fine...enjoy!
Click to expand...


Hey Scalder, the MM&FF article says you really feel it in 4th gear, it pulls harder. What is your experience? thanks.
 

scalder

Member
Aug 1, 2003
375
0
16
Dallas/Plano TX
Feb 27, 2004
#6
  • Feb 27, 2004
  • #6
That's funny! I was with my buddy shortly after the install and he noticed how much harder it charged in 4th... I think you'll really notice the imporvment...
 
B

bennyjammin

New Member
Oct 13, 2003
62
0
0
Feb 27, 2004
#7
  • Feb 27, 2004
  • #7
I disagree. I think you will run lean and may run into detonation or pinging. Look at my mods- I have almost the same setup as you. Once I installed the Superchips performance setting I immediately got detonation. The only way I was able to stop the pinging was with the Pro-M remote optimizer.

Keep in mind, I can only get 91 octane in CA. So you may not ping if you can get 93 octane.
 

scalder

Member
Aug 1, 2003
375
0
16
Dallas/Plano TX
Feb 27, 2004
#8
  • Feb 27, 2004
  • #8
That has to be it....I'm running over 15 degrees advance without any pinging at all...
 
C

CatmanJJ

Captain Tangnet
20+ Year Stangneter
Feb 5, 2002
4,379
1
68
Maryland
Feb 27, 2004
#9
  • Feb 27, 2004
  • #9
My friend has all the bolt-ons with plenum/75mm TB and tuner and his car runs great.
 

BlackVert

15 Year Member
Oct 3, 2003
5,589
9
98
Bethesda, MD
Feb 27, 2004
#10
  • Feb 27, 2004
  • #10
I installed this stuff over my lunch break yesterday:

- C&L MAF (80 or 85mm, I can't remember rith now!) kit w/K&N
- C&L TrueFlow pipe
- AccuFab 75mm TB
- C&L plenum

I got it all at http://www.rpmoutlet.com for abt $750 with free shipping.

It took 1 1/2 hours and I had these problems:

- The connector on the back of the plenum was too big for the hose that goes there (I made a make-shift adapter to reconnect them)
- The pipe did not fit under my strut tower brace (I think it is stock on the verts); I had to loosen the brace to get it in.
- I did not have time yesterday to disconnect the battery and now I am getting a check engine light.
- It pings alot when under a load (the T/A is set to 14 and I use 93 octane all the time); I'm guessing it is too lean.

This afternoon I disconnected the battery for an hour and re-did the hose connector (still not happy with it but it's better). I just reconnected the battery, but I haven't had time to drive it yet to see how it is.

I'm still not sure what to do about the brace, I'll probably try to put a spacer under the top bolt to lift it or something like that.
 

sasscuba

Member
Dec 24, 2003
304
0
16
Tulsa Oklahoma
Feb 28, 2004
#11
  • Feb 28, 2004
  • #11
Anyone else with this combo, need somemore feedback before buying the C&L and the TB.
 

BlackVert

15 Year Member
Oct 3, 2003
5,589
9
98
Bethesda, MD
Feb 28, 2004
#12
  • Feb 28, 2004
  • #12
Well, no pinging today, but I still have the check engine light. I am thinking the TPS is off and that is causing the check engine light.

Plus, it is acting like it did when IAC was stuck open, hanging at around 1500 or so and then finally going down about 5 seconds after comingo to a complete stop. Probably a vaccuum leak, I didn't replace any gasgets so that is probably what is going on there.

The positive thing is that it feels stronger above 3000 RPM
 
You must log in or register to reply here.

Similar threads

S
Engine Will 02-04 C&L Plenum fit on my 2001 Mustang GT?
  • Stangg338
  • Nov 15, 2020
  • SN95 4.6L Mustang Tech
Replies
3
Views
5K
SN95 4.6L Mustang Tech Oct 22, 2024
89ripper
I
Progress Thread Exorcising a '76 Coupe
  • IICrew
  • Oct 12, 2020
  • 1974 - 1978 Mustang II Talk & Tech
  • 2
Replies
31
Views
5K
1974 - 1978 Mustang II Talk & Tech Jul 3, 2022
2Blue2
A
Fuel & Tuning setup for upcoming 00' S/C GT Questions
  • alwayshi
  • Jun 20, 2019
  • SN95 4.6L Mustang Tech
Replies
0
Views
1K
SN95 4.6L Mustang Tech Jun 20, 2019
alwayshi
A
A
Progress Thread alwayshi 00 GT supercharged build
  • alwayshi
  • Nov 7, 2019
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • 2
Replies
26
Views
8K
1996 - 2004 SN95 Mustang -General/Talk- Aug 9, 2020
Deleted member 38176
D
N
2007 Mustang GT Cold Engine and Hesitation Problem
  • noahgt
  • Nov 17, 2020
  • 2005 - 2014 S-197 Mustang -General/Talk-
Replies
2
Views
2K
2005 - 2014 S-197 Mustang -General/Talk- Dec 24, 2020
McFly2
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?