• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech

Car Dies/Mass Air Question

  • Thread starter Thread starter 94MustangGT5.0
  • Start date Start date Jun 27, 2005

94MustangGT5.0

New Member
Apr 30, 2003
288
0
0
Champaign, Illinois
Jun 27, 2005
#1
  • Jun 27, 2005
  • #1
This past weekend I had trouble with my car wanting to die when I put it in gear. The RPM's would fall, the car would surge for a moment, then just die. It did this for about 5 starts then was fine. Well, I popped the hood and unplugged my mass air with the car running, and nothing happened? I had remembered doing this before after and the car imediately started running rough. However, this time nothing changed. I reved it up and still noticed nothing different, not appearing to be running lean or rich. My question is this: Shouldn't the car have started running rough or even died when I unplugged the mass air? Can anyone else unplug theres and not even hear a change in idle or anything? Just wondering if something might be wrong because it seems as though my car runs like the old speed density cars and doesn't even need a mass air meter right now. I know this isn't necessarily a bad thing that my car doesn't die when I unplug it, just wondered why this would be. Thanks in advance.
 

DoHcHoLlIdAy01

New Member
May 28, 2005
46
0
0
Los Angeles, CA
Jun 27, 2005
#2
  • Jun 27, 2005
  • #2
If you have had the Pro-M on there for a while and you have a K&N you might want to spray the MAFS with carb cleaner.
 

CManT1914

New Member
Feb 5, 2004
3,172
2
0
Killeen, Texas
Jun 27, 2005
#3
  • Jun 27, 2005
  • #3
I know when my MAF fell off a couple weeks ago (if you have an AFM powerpipe, you'd understand), it wouldn't die or run like crap right away. It took about 10 seconds or so. Then later when I started it with the MAF still off, it would sometimes run decent enough to drive around the block (don't ask me why I tried this, lol). Good luck
-Chris
 

legalize420

Active Member
May 21, 2005
1,541
1
37
South Florida
Jun 27, 2005
#4
  • Jun 27, 2005
  • #4
i know when mine is unpluged the check engine light comes on. could it be a charging issue?
 

mo_dingo

20+ Year Stangneter
Aug 26, 2003
3,031
2
58
Tucson, AZ
Jun 27, 2005
#5
  • Jun 27, 2005
  • #5
94MustangGT5.0 said:
This past weekend I had trouble with my car wanting to die when I put it in gear. The RPM's would fall, the car would surge for a moment, then just die. It did this for about 5 starts then was fine. Well, I popped the hood and unplugged my mass air with the car running, and nothing happened? I had remembered doing this before after and the car imediately started running rough. However, this time nothing changed. I reved it up and still noticed nothing different, not appearing to be running lean or rich. My question is this: Shouldn't the car have started running rough or even died when I unplugged the mass air? Can anyone else unplug theres and not even hear a change in idle or anything? Just wondering if something might be wrong because it seems as though my car runs like the old speed density cars and doesn't even need a mass air meter right now. I know this isn't necessarily a bad thing that my car doesn't die when I unplug it, just wondered why this would be. Thanks in advance.
Click to expand...


Lets clear a few things up. The mass air controls the a/f ratio for only a couple minutes after startup. This gives the O2's time to heat up and start working.

If the car starts to clear up after a few minutes, it's definately a MAF/ECT/IAT problem. Likely you have an oiled filter and need to clean the MAF sensor.

Take the 2 t-20 (or t-25) safety torx headed screws off of the MAF sensor element and carefully seperate the sensor from the housing. Clean the two resistors with a q-tip and alcohol and let dry.
Scott
 
You must log in or register to reply here.

Similar threads

T
Help with a 95 5L crank no start
  • TheBubbaJoe
  • Nov 4, 2025
  • 1994 - 1995 Specific Tech
Replies
3
Views
446
1994 - 1995 Specific Tech Nov 5, 2025
AeroCoupe
W
Engine My engine dies after running 10 to 15 minutes under high heat.
  • Wylieone
  • Jun 21, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
174
Fox 5.0 Mustang Tech Jun 22, 2026
Mustang5L5
Distributor installed wrong
  • djj62478
  • Jun 14, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
184
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 21, 2026
CAMTWO1070
J
Emission problems
  • jls.zmmr
  • Feb 5, 2026
  • 1994 - 1995 Specific Tech
Replies
2
Views
243
1994 - 1995 Specific Tech Feb 7, 2026
AeroCoupe
Problems after exhaust install and 02 harness
  • djj62478
  • Jul 2, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
39
Views
491
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Saturday at 10:37 PM
AeroCoupe
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?