• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Car trying to start with out the key turned?

  • Thread starter Thread starter rwood126
  • Start date Start date May 10, 2009
R

rwood126

Member
Feb 20, 2009
161
3
16
mCdONOUGH, GA.
May 10, 2009
#1
  • May 10, 2009
  • #1
Ok...heres the deal. My starter when out last night...so (I thought. I had to un plug the battery to get the starter to stop spinning.) I just replaced it 10 minuts ago. I went and hooked up the battery cables and the car startes turning over....no key in the ingnition or no clutch pressed in.


Any ideas?
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
May 10, 2009
#2
  • May 10, 2009
  • #2
The starter solenoid has stuck the contacts together. Usually this is result of a low battery or some bad connections. Clean and check all the connections before proceeding. The battery posts and inside of the battery post terminals should be scraped clean with a knife or cleaner brush tool.

The clamp on with 2 bolts battery terminal ends are a know problem causer. Anyplace you see green on a copper wire is corrosion. Corrosion gets in the clamped joint and works its way up the wire under the insulation. Avoid them like the plague...

The fix for stuck contacts is to smack the bottom side of the starter solenoid to get the contacts unstuck.

If that does not work, remove the small red/blue wire that is stuck on a screw. It is the wire from the ignition switch that energizes the starter solenoid. If that fixes the problem (unlikely, but possible), replace the ignition switch.


If that does not work, replace the starter solenoid. A wiring diagram of the solenoid follows...

Starter solenoid wiring for 86-91 Mustang



Starter solenoid wiring 92-93 Mustang or earlier Mustang with upgraded high torque mini starter.
 
R

rwood126

Member
Feb 20, 2009
161
3
16
mCdONOUGH, GA.
May 10, 2009
#3
  • May 10, 2009
  • #3
Thanks...

I guess when the starter locked up it caused the solenoid to go bad. Just replaced the solenoid...fire right up. I'm not going to keep the aftermarket solenoid on there....it's real cheap looking. I'll get a new OEM solenoid tomorrow when I go into work.

I know that I don't want to have to change out that starter again any time soon...
 
You must log in or register to reply here.

Similar threads

A
1987 5.0 speed density Foxbody crank no start
  • Alan2204
  • May 23, 2026
  • Fox 5.0 Mustang Tech
Replies
10
Views
293
Fox 5.0 Mustang Tech May 30, 2026
Mcmahst
C
Electrical HELP! 1989 5.0 Stick, Voltage Bleed onto Ignition Trigger wire
  • ChickenDeluxe
  • May 14, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
228
Fox 5.0 Mustang Tech May 24, 2026
ChickenDeluxe
C
E
2007 GT Stalls when lights or a/c turned on
  • ejscarfo
  • Jun 22, 2026
  • 2005 - 2009 Specific Tech
Replies
2
Views
133
2005 - 2009 Specific Tech Jun 29, 2026
ejscarfo
E
Alternator not charging
  • SchwarzStock
  • Jul 6, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
2
Views
79
1965 - 1973 Classic Mustangs -General/Talk- Jul 19, 2026
SchwarzStock
8
Electrical Crank-no start ... no spark ... no injector pulse, was it something I did? (redux)
  • 85gtCOBRA
  • Oct 28, 2025
  • Fox 5.0 Mustang Tech
Replies
2
Views
568
Fox 5.0 Mustang Tech Oct 29, 2025
85gtCOBRA
8
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?