• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech

Checking The Rearend Oil In The Driveway

  • Thread starter Thread starter Pearl02
  • Start date Start date Jul 23, 2006

Pearl02

Member
Nov 27, 2004
496
0
16
Kansas City
Jul 23, 2006
#1
  • Jul 23, 2006
  • #1
It appears my pinion seal is leaking. I know I will have to have it fixed. How do you check your diff oil at home. I know I'll have to jack the car up some. My concern is I won't get a accurate measurement because the rearend willbe in the air. It would be much easier if I had a lift. Thanks Pearl02.
 

03ghoststang

Well-Known Member
Jul 16, 2005
1,930
1
57
Los Angeles, California
Jul 23, 2006
#2
  • Jul 23, 2006
  • #2
well i t will be har to do cause the car wont be leveled but i would just get it fixed........ and is it a bad leak that it leaves puddles on the drive way or minor leak
 

DTNODYA

Member
Dec 15, 2005
831
1
16
Jul 23, 2006
#3
  • Jul 23, 2006
  • #3
Jack the car up as level as you can, take the fill plug out of the differential and stick your pinky finger in the hole. If you don't feel fluid level with the bottom of your finger then it is low. Whatever you do, be safe and make sure the car is sturdy on the stands.
 

Pearl02

Member
Nov 27, 2004
496
0
16
Kansas City
Jul 23, 2006
#4
  • Jul 23, 2006
  • #4
03ghoststang said:
well i t will be har to do cause the car wont be leveled but i would just get it fixed........ and is it a bad leak that it leaves puddles on the drive way or minor leak
Click to expand...

No puddles in the driveway. I didn't know about the leak until I was hooking up my speed cal. Pearl02.
 

03ghoststang

Well-Known Member
Jul 16, 2005
1,930
1
57
Los Angeles, California
Jul 23, 2006
#5
  • Jul 23, 2006
  • #5
DTNODYA said:
Jack the car up as level as you can, take the fill plug out of the differential and stick your pinky finger in the hole. If you don't feel fluid level with the bottom of your finger then it is low. Whatever you do, be safe and make sure the car is sturdy on the stands.
Click to expand...


i agree with what you mentioned here
 

Red99GTVert

New Member
May 16, 2006
11
0
0
Buffalo, NY
Jul 23, 2006
#6
  • Jul 23, 2006
  • #6
I ran the rear of the car halfway up a set of ramps to check my level. I removed the fill plug and fluid started gushing out.....my level was fine I do need to get a rebuild myself - bad pinion or carrier bearing threw off the backlash and the rear end growls like a bear.

One word of advice - don't hit your head on the gas tank like I did! Hurts like hell and I have a little cut on my forehead.
 

03ghoststang

Well-Known Member
Jul 16, 2005
1,930
1
57
Los Angeles, California
Jul 24, 2006
#7
  • Jul 24, 2006
  • #7
Red99GTVert said:
I ran the rear of the car halfway up a set of ramps to check my level. I removed the fill plug and fluid started gushing out.....my level was fine I do need to get a rebuild myself - bad pinion or carrier bearing threw off the backlash and the rear end growls like a bear.

One word of advice - don't hit your head on the gas tank like I did! Hurts like hell and I have a little cut on my forehead.
Click to expand...


you need to get that done ASAP or you'll be doing more than just a rebuild....

lol since i do all of my gear installs on the floor i have banged my head a couple times in different areas
 

Pearl02

Member
Nov 27, 2004
496
0
16
Kansas City
Jul 24, 2006
#8
  • Jul 24, 2006
  • #8
Here's a update. I was able to check the fluid level today. I lifted the car from the back using the jacking points(not the diff). I lifted the car enough to get underneath there. I left the tires on the ground. As I was pulling the pulg from the diff I noticed it had pressure on it. I slowly allowed for the pressure to bleed off and pulled the plug. I pulled the plug and some fluied ran out. I put the plug back on. I also noticed the the pinion seal area was dry. I believe that my vent tube has a kink or bend in it not allowing the diff to vent prperly. That could be way my pinion started to leak. I'll have to go under there again to check it out. Any thoughts? Pearl02.
 
You must log in or register to reply here.

Similar threads

O
Progress Thread LTD-ing
  • OX1
  • Mar 15, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
8
Views
388
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Apr 6, 2026
OX1
O
Drivetrain Rear end clunk
  • seanmahoney
  • Oct 13, 2025
  • SN95 4.6L Mustang Tech
Replies
3
Views
419
SN95 4.6L Mustang Tech Oct 13, 2025
nickyb
N
Edelbrock 1405 Setup
  • nathantaylor200
  • Nov 4, 2025
  • Classic Mustang Specific Tech
Replies
3
Views
246
Classic Mustang Specific Tech Nov 5, 2025
nathantaylor200
N
3
Eight inches is enough for me...
  • 351MooseStang
  • Nov 27, 2025
  • 1974 - 1978 Mustang II Talk & Tech
Replies
5
Views
584
1974 - 1978 Mustang II Talk & Tech Mar 2, 2026
Bullitt347
Engine New Oil Leak Help.
  • Slo5Oh89
  • Mar 14, 2025
  • Fox 5.0 Mustang Tech
Replies
8
Views
609
Fox 5.0 Mustang Tech Mar 19, 2025
Slo5Oh89
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?