clutch question

disturbdgt

Member

Apr 8, 2007

90

0

7

suffolk, va

Mar 6, 2012

#1

• Mar 6, 2012

• #1

i just noticed today that when i push my clutch pedal in all the way, i can hear the clutch still spinning. its like a smooth surface rub sound (sorry only way i can describe it). also i noticed lately that sometimes i have to use a little more effort to shift into each gear. but when i get it into gear, it does not slip out. could this mean that i need to adjust my clutch cable, or that the cable has stretched? much help with this problem will be greatly appreciated.

 

BradleyMustang3

Member

Jun 4, 2011

148

0

17

New York

Mar 6, 2012

#2

• Mar 6, 2012

• #2

take your toe and pull up on the clutch pedal then push it all the way to the floor....do this a few times it should self adjust if that is the issue...i just had the same issue with mine and thats how it started it ended being a throwout bearing....if it doesnt quiet down after the adjust get underneath the car and look at where the clutch cable sits into the clutch fork there should be a slight amount of play but not enough that you can slide the end of the cable out of where it sits into the fork with little force...if its adjusted properly it should take a little bit of pressure to get it to come out...if you get under there and it seems good plan on dropping your trans....

 

disturbdgt

Member

Apr 8, 2007

90

0

7

suffolk, va

Mar 6, 2012

#3

• Mar 6, 2012

• #3

also forgot to add that i have an aftermarket quadrant and cable

 

disturbdgt

Member

Apr 8, 2007

90

0

7

suffolk, va

Mar 6, 2012

#4

• Mar 6, 2012

• #4

BradleyMustang3 said:

take your toe and pull up on the clutch pedal then push it all the way to the floor....do this a few times it should self adjust if that is the issue...i just had the same issue with mine and thats how it started it ended being a throwout bearing....if it doesnt quiet down after the adjust get underneath the car and look at where the clutch cable sits into the clutch fork there should be a slight amount of play but not enough that you can slide the end of the cable out of where it sits into the fork with little force...if its adjusted properly it should take a little bit of pressure to get it to come out...if you get under there and it seems good plan on dropping your trans....

Click to expand...

about a month or so ago i did notice a chirpping sound coming from the trans, which is more than likely the throwout bearing. if the throwout bearing completely went bad could this be the culprit?

 

BradleyMustang3

Member

Jun 4, 2011

148

0

17

New York

Mar 6, 2012

#5

• Mar 6, 2012

• #5

yeah i like the call the sound a dying chipmunk as my car does this now...i should actually be in bed seeing as im replacing the entire clutch kit tomorrow...haha yeah if its making that sound and its adjusted right its the throwout bearing...and if you installed the clutch yourself take a look at the fly wheel next time youre in there it may need resurfacing before you install the new clutch...or it could be cheaper to just buy a lightweight one. your call.

 

disturbdgt

Member

Apr 8, 2007

90

0

7

suffolk, va

Mar 6, 2012

#6

• Mar 6, 2012

• #6

well the clutch was put in about 2.5 years ago. also forgot to add that i have to pretty much leg press my clutch pedal (meaning its kinda stiff and takes a lot of pressure to hold it in.)

 

BradleyMustang3

Member

Jun 4, 2011

148

0

17

New York

Mar 6, 2012

#7

• Mar 6, 2012

• #7

has it always been that stiff? if so then its most likely just a throwout bearing. just give everything a good look when you drop the trans.

 

disturbdgt

Member

Apr 8, 2007

90

0

7

suffolk, va

Mar 6, 2012

#8

• Mar 6, 2012

• #8

i wanna say it became stiff shortly after the new clutch was installed 2.5 years ago