• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Code 31 Problem

  • Thread starter Thread starter dcurtis
  • Start date Start date Oct 13, 2007

dcurtis

10 Year Member
Jan 19, 2006
688
7
39
Oct 13, 2007
#1
  • Oct 13, 2007
  • #1
Ok, I have had the code 31 for a while now, thought I had it fixxed but I was wrong, this morning I checked the voltage to the egr, I think the wires are the sig return, vref and I dont remember what the other is right now, but anyways I got the 5 volts at the sig rtrn to the vref and from the othetr wire, the one I cant ramember, was at .36 or .38, and from what I've read as long as it's below .67 the wiring to the egr is ok, so why do I still get the code 31, I think the other wire was evp(just remembered that) anyways what else could cause the 31, because I am stumped now, do I need to just get a new egr or what?
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Oct 13, 2007
#2
  • Oct 13, 2007
  • #2
Not much help, but here it is..
b]CODE: 31[/b] (KOEO) - EVP circuit below minimum voltage. Vref (5 volt reference voltage supplied by the computer) missing or broken wire or bad connection in circuit. Use a DVM to check for 5 volts on the orange/white wire. If it is missing, look for +5 volts at the orange/white wire on the TPS or MAP sensor located on the firewall near the center of the car. Use the black/white wire for the ground for the DVM.
With the sensor removed from the EGR and still connected, press the plunger and watch the voltage change on the brown/lt green wire. Pull the passenger side kick panel and measure the voltage at the computer. You will need to remove the plastic cover over the wires and probe them from the backside. A safety pin may prove very useful for this task. Use pin 27, EVR input (brown/lt green wire) and pin 46, signal ground (black/white wire) to measure the voltage. The orange/white wire is Vref and should always be 5 volts -/+ .25 volt. Be sure to measure Vref at the EGR sensor to rule out any broken wires or bad connections.
 
You must log in or register to reply here.

Similar threads

Electrical Code 29 again
  • Creomod
  • Jul 31, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
393
Fox 5.0 Mustang Tech Aug 3, 2026
Creomod
J
Thanks for the information on codes 31,34,44 and 94!
  • JK86LX50
  • Mar 5, 2025
  • The Welcome Wagon
Replies
3
Views
378
The Welcome Wagon Aug 5, 2025
gkomo
Alternator not charging
  • SchwarzStock
  • Jul 6, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
3
Views
269
1965 - 1973 Classic Mustangs -General/Talk- Oct 17, 2026
SchwarzStock
Resolved 93 Mustang 5.0 - Cranks but does not start
  • dan50
  • Jul 18, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
487
Fox 5.0 Mustang Tech Jul 18, 2026
dan50
R
93 LX 2.3 Trouble codes 53, 85, 21 help
  • Rickshaw302
  • Apr 15, 2025
  • 2.3L (N/A & Turbo) Tech
Replies
17
Views
840
2.3L (N/A & Turbo) Tech Apr 18, 2025
AeroCoupe
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?