• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Code 98 and 64 K.O.E.R

  • Thread starter Thread starter BK_CAULEY
  • Start date Start date Sep 17, 2007

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Sep 17, 2007
#1
  • Sep 17, 2007
  • #1
as the title states im getting a key on engine running codes 98 and 64 could someone please explain what they are and how do i fix them. when i do a K.O.E.O test it gives me 11.
 

302RollinHard

New Member
Sep 26, 2005
0
0
0
Columbus, OH
Sep 18, 2007
#2
  • Sep 18, 2007
  • #2
code 98 is a hard fault code. Something like your MAF, ECT, or ACT sensor is unplugged or fubarred making the car run in limp home mode. Code 64 is an ACT sensor code. Maybe you left it unplugged???
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Sep 18, 2007
#3
  • Sep 18, 2007
  • #3
Code 98 - basic computer internal tests not passed before it started processing the request to dump codes.
Do a Key On Engine Off test before starting the engine. Wait until you see the 11 flash before pressing any buttons
if you have a hand operated scanner. The computer is operating in Limp mode, so fix any codes it dumps prior to doing
anything else.

Code 64 – ACT (Air Charge Temperature) signal low or grounded. Bad sensor,
sensor wiring on pin 25 shorted to ground, or bad computer.

Note that all resistance tests must be done with power off. Measuring
resistance with a circuit powered on will give false readings and possibly
damage the meter.


The ACT is located in the #5 intake runner on Mustangs built from 86-93
. Disconnect the sensor by removing the sensor wiring connector. Measure
the resistance across the sensor pins.

Ohms measures at the computer with the computer disconnected, or at the
sensor with the sensor disconnected.
50 degrees F = 58.75 K ohms
68 degrees F = 37.30 K ohms
86 degrees F = 27.27 K ohms
104 degrees F = 16.15 K ohms
122 degrees F = 10.97 K ohms
140 degrees F = 7.60 K ohms
158 degrees F = 5.37 K ohms
176 degrees F = 3.84 K ohms
194 degrees F = 2.80 K ohms

If the sensor resistances read good according to the table, remove
the passenger side kick panel and disconnect the computer connector.
A single 10 MM bolt secures the connector in place. With the sensor
connector still disconnected, measure the resistance between pin 25
(lt green/pink wire) and ground. If you wish, you can make your
measurements at the ACT sensor end. This will save you from
counting the computer connector pins to locate the correct one.
However, you will still have to disconnect the computer connector.
You should see 100K Ohms or greater between pin 25 and ground.
Less than that indicates wiring problems with the pin 25
lt green/pink wire shorted to ground. Note that the following
diagram on the connector displays the pins viewed from the
computer side.



See following website for some help from Tmoss
(diagram designer) & Stang&2Birds (website host) for
help on 88-95 wiring http://www.veryuseful.com/mustang/tech/engine/
http://www.veryuseful.com/mustang/tech/engine/images/88-91eecPinout.gif

Diagram courtesy of Tmoss & Stang&2birds

 
You must log in or register to reply here.

Similar threads

Electrical Code 29 again
  • Creomod
  • Jul 31, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
393
Fox 5.0 Mustang Tech Aug 3, 2026
Creomod
S
92 5.0 almost starts
  • Steverino
  • Sep 23, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
5
Views
277
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 25, 2026
General karthief
Engine Code 41 again
  • Creomod
  • Jul 7, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
23
Views
863
Fox 5.0 Mustang Tech Jul 11, 2026
Mcmahst
W
I need a 1997 Mustang PATS A expert!
  • Wolfdogg
  • Oct 2, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
3
Views
204
1996 - 2004 SN95 Mustang -General/Talk- Oct 5, 2026
Noobz347
K
Electrical 2000 GT Intermittent Engine Shutdown In Motion - DTC U1262
  • kenster1092
  • Apr 13, 2026
  • SN95 4.6L Mustang Tech
Replies
4
Views
362
SN95 4.6L Mustang Tech Apr 24, 2026
squeak93
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?