• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Computer

  • Thread starter Thread starter ghostang93
  • Start date Start date May 31, 2007

ghostang93

Member
Mar 26, 2007
29
0
12
Pace, FL
May 31, 2007
#1
  • May 31, 2007
  • #1
Does anyone know if the Cardone replacement computers are any good? I'm grasping at straws to fix my WOT problem. I'm hoping the previous owner had the ECU tuned to his supercharged engine that was previously in the car.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
May 31, 2007
#2
  • May 31, 2007
  • #2
You cannot readily flash a fox III puter, so if you don't see a chip or an interface, chances are that you are ok. And honestly, I'd not look at the puter as a reason for a WOT issue in general. But no info is known.

Good luck.
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
May 31, 2007
#3
  • May 31, 2007
  • #3
^What he said...

Pull the codes, and see what the computer thinks.


If there isn't a chip, then it probably hasn't been tuned.


Describe the 'WOT problem'
The ecu is the not a common failure...


jason
 

ghostang93

Member
Mar 26, 2007
29
0
12
Pace, FL
May 31, 2007
#4
  • May 31, 2007
  • #4
I posted my problem a few days ago, but I can't find the post. Basically it breaks up when i stomp on the gas. Only full throttle and above 3500. It acts and runs great at part throttle. Only codes it showing are the emissions junk that's not on there. Thermo, EGR, ect.. Plugs, wires, msd, tfi module, MAF are all good/clean. Fuel pressure set at 40psi w/o vacuum hooked up, I've lowered and raised it slightly to no effect. Pressure does not drop under WOT either. Timing is set to 12 w/o spout.

Edit: By the way, Although there is a rectangle cut into the side of the computer, I don't see a chip.
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
May 31, 2007
#5
  • May 31, 2007
  • #5
ghostang93 said:
I posted my problem a few days ago, but I can't find the post. Basically it breaks up when i stomp on the gas. Only full throttle and above 3500. It acts and runs great at part throttle. Only codes it showing are the emissions junk that's not on there. Thermo, EGR, ect.. Plugs, wires, msd, tfi module, MAF are all good/clean. Fuel pressure set at 40psi w/o vacuum hooked up, I've lowered and raised it slightly to no effect. Pressure does not drop under WOT either. Timing is set to 12 w/o spout.

Edit: By the way, Although there is a rectangle cut into the side of the computer, I don't see a chip.
Click to expand...

No chip does imply that there has been NO tune done.


I'm at a loss...
It may help if you post the code numbers?



jason
 

ghostang93

Member
Mar 26, 2007
29
0
12
Pace, FL
May 31, 2007
#6
  • May 31, 2007
  • #6
Previously complied with unfortunately. I set it at 40 when i put my aeromotive FPR on. I've varied both up and down.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
May 31, 2007
#7
  • May 31, 2007
  • #7
FWIW, what you described can be due to a bad coil, TFI or too large of a plug gap.
For the former two, I'd not buy new parts, but if you're a packrat, you might have spares to try out.

It sounds like you swapped the plugs out from whatever plugs and gap were run for the blower, but I figured I'd ask.

Good luck.
 

ghostang93

Member
Mar 26, 2007
29
0
12
Pace, FL
May 31, 2007
#8
  • May 31, 2007
  • #8
Yes, the the plugs and wires are new. And you're right, I'm a packrat and have extras and have swapped them already. I am running the stock gap size for my heads, .042 i think is what explorers call for.
 
You must log in or register to reply here.

Similar threads

G
Engine ECU Question
  • GeorgeE
  • Oct 12, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
27
Views
718
Fox 5.0 Mustang Tech Oct 19, 2026
JD1964
9
Electrical F150 ECU in a Foxbody? Idle surge help
  • 93royalblue
  • Sep 10, 2025
  • Fox 5.0 Mustang Tech
Replies
6
Views
573
Fox 5.0 Mustang Tech Sep 17, 2025
Mustang5L5
Electrical Code 29 again
  • Creomod
  • Jul 31, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
393
Fox 5.0 Mustang Tech Aug 3, 2026
Creomod
A
A/F ratio gauge install questions.
  • AngryH58
  • Sep 24, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
5
Views
253
1996 - 2004 SN95 Mustang -General/Talk- Oct 22, 2026
Noobz347
S
ECU/PCM ISSUE
  • Santi1015
  • Jun 29, 2026
  • SN95 4.6L Mustang Tech
Replies
2
Views
273
SN95 4.6L Mustang Tech Jun 29, 2026
Santi1015
S
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?