• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech

Crank but no start. Fuel pump? No Spark? Both?!%

  • Thread starter Thread starter will_95gt
  • Start date Start date Dec 5, 2010

will_95gt

Member
Jul 27, 2004
298
1
16
Austin, TX
Dec 5, 2010
#1
  • Dec 5, 2010
  • #1
Ok, so after writing a beautifully detailed grocery list, I hopped into the car to head to the store. When I turned the key, the motor cranked but wouldn't start.

I tested the battery and it's fully charged, so I started looking suspiciously at the fuel system. I hopped back in the car and turned the key to the off position and back to the on position, priming the fuel lines, 2 or 3 times and then gave it another crank. Still nothing.

I checked the inertia cut-off switch in the trunk and it hadn't been activated so I slid under the car and checked the fuel lines leading to and from the fuel filter and they looked fine. I then primed the lines two more times, removed the cap from the schrader valve on the fuel rail and pressed in the valve with a small allen wrench expecting a tiny shower of fuel. What I got was a quick blast of air and not much else. I depressed the valve again (this time holding it for a little longer) and once again got mostly air--there was some slight moisture along with it kind of like when you hold a compressed air can in the wrong position and a bit of moisture fires out.

This boggled me because I'm fairly certain that I can hear the fuel pump coming on when I turn the key. I immediately pulled a spark plug to see if it had any moisture on it and it seemed fairly dry.

I pulled another spark plug to do the same test and it crumbled to pieces...the inside of the plug had rusted so when I pulled the plug its innards all came tumbling out and scattered in shards across my distributor cap.

GREAT. Now I may have a fuel issue AND a spark plug issue.


Here's my question: If I can hear the fuel pump coming on (which I think I can) shouldn't the shrader valve test have yielded a shower of gas and not a burst of air? If so, what should my next step be in diagnosing the fuel issue?

Also, is it possible that the rusted out plug may have been the culprit this entire time? In other words, is it common to get occasional air blasting from the fuel lines?

 

KamiKaziDK

Member
May 16, 2005
555
0
17
Mesa, Az
Dec 5, 2010
#2
  • Dec 5, 2010
  • #2
Maybe it locked up, or maybe something internal went out and it's spinning but not pumping fuel, sadly I've had that happen before. But if I were you, I'd put all new plugs and wires on first and go from there, might not be fuel at all.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Dec 6, 2010
#3
  • Dec 6, 2010
  • #3
Get a FP gauge and see what's going on. The gauge will tell you (don't forget about the fuel filter if pressure is down).

You could use a priming fluid (starting fluid, etc) to see if it will burp.
 

will_95gt

Member
Jul 27, 2004
298
1
16
Austin, TX
Dec 6, 2010
#4
  • Dec 6, 2010
  • #4
Alright. I've got a FP gauge but the fitting didn't seem to be applicable to the shrader valve. The weird thing is, I know I've used it before So I'll just have to tinker around and remember how I used it last time.

Before I start diagnosing fuel issues I'll have to wait on some new spark plug wires. It's annoying because every other plug wire seems to be in great shape, does anybody know if you can order wires individually? I've only seen sets for sale online. That's probably a dumb question.

Btw, thanks for the responses, guys.

Hissin: I like that priming fluid idea. Although I know the purpose and application of priming fluid I've never actually used any. Could you elaborate on that process? Where exactly in the fuel system does one inject the priming fluid? Somewhere close to the motor I would assume? lol
 

revhead347

Apparently my ex-husband made that mistake.
20+ Year Stangneter
Jun 14, 2004
9,301
1,644
214
Acworth, GA
Dec 6, 2010
#5
  • Dec 6, 2010
  • #5
Usually you unscrew the schraeder, and screw it directly into the fuel pressure rail. It's 1/8" NPT.

Kurt
 

GRAYFOXGT/CS

New Member
Nov 27, 2010
30
0
0
AZ
Dec 6, 2010
#6
  • Dec 6, 2010
  • #6
I had this happen to me the plug in connector on the 5.0 under the coil came loose and i wasnt gettin spark Check that and see, and for the rust that cant be good.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Dec 6, 2010
#7
  • Dec 6, 2010
  • #7
will_95gt said:
Hissin: I like that priming fluid idea. Although I know the purpose and application of priming fluid I've never actually used any. Could you elaborate on that process? Where exactly in the fuel system does one inject the priming fluid? Somewhere close to the motor I would assume? lol
Click to expand...

You can spray a little starter fluid into the TB. Be careful because ether is so flammable.

You can sometimes find a generic spark-plug wire at the parts store. That might tide you over till you can get some new wires.
 

will_95gt

Member
Jul 27, 2004
298
1
16
Austin, TX
Dec 7, 2010
#8
  • Dec 7, 2010
  • #8
revhead347 said:
Usually you unscrew the schraeder, and screw it directly into the fuel pressure rail. It's 1/8" NPT.

Kurt
Click to expand...

Ahh, I figured there was some sort of step I wasn't considering, lol. Thanks.

GRAYFOXGT/CS said:
I had this happen to me the plug in connector on the 5.0 under the coil came loose and i wasnt gettin spark Check that and see, and for the rust that cant be good.
Click to expand...

Interesting. I'll see if I can pin point that plug and make sure its properly seated. Thanks for the tip!


BTW am I the only one here who gets excited when I have car parts coming in the mail even when they're as trivial as spark plug wires and a fuel filter?? The anticipation is killing me!
 
You must log in or register to reply here.

Similar threads

A
1987 5.0 speed density Foxbody crank no start
  • Alan2204
  • May 23, 2026
  • Fox 5.0 Mustang Tech
Replies
10
Views
309
Fox 5.0 Mustang Tech May 30, 2026
Mcmahst
9
1995 5.0 just cranks
  • 9GT5
  • Jun 29, 2025
  • 1994 - 1995 Specific Tech
Replies
1
Views
370
1994 - 1995 Specific Tech Jun 29, 2025
AeroCoupe
L
1997 V6 Starting issue
  • leanzik04
  • Mar 20, 2026
  • SN95 V6 Mustang Tech
Replies
3
Views
247
SN95 V6 Mustang Tech Mar 20, 2026
Noobz347
T
Help with a 95 5L crank no start
  • TheBubbaJoe
  • Nov 4, 2025
  • 1994 - 1995 Specific Tech
Replies
3
Views
451
1994 - 1995 Specific Tech Nov 5, 2025
AeroCoupe
Resolved 93 Mustang 5.0 - Cranks but does not start
  • dan50
  • Jul 18, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
131
Fox 5.0 Mustang Tech Jul 18, 2026
dan50
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?