• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Damn Code 34!!!!!!!!!

  • Thread starter Thread starter jaymac
  • Start date Start date Nov 4, 2005

jaymac

New Member
Feb 18, 2004
995
0
0
Northern Mass
Nov 4, 2005
#1
  • Nov 4, 2005
  • #1
I've had code 34 now for more than a year "EVP voltage above closed unit".
yesterday I tried an EGR from another car, and got the same exact code, even after disconnecting the battery. Yes, it could be chance that that one was bad (did not have the keys to run the code), but what else could be the cause/culprit of a code 34??
Thanks,
J
 
S

slickshift

New Member
Aug 19, 2004
51
0
0
New England
Nov 4, 2005
#2
  • Nov 4, 2005
  • #2
Code 34

KOEO (Engine Off)= EVP:See if code 84 is present; PFE:low exhaust backpressure, blocked sensor tube, bad sensor

KOER (Engine Running)= EGRC/EGRV: EGR valve opening not detected; EVR: EVP or PFE signal too high

CM (Continuous Memory)= PFE: check for blocked sensor tube; EVP: check EVP resistance
 

jaymac

New Member
Feb 18, 2004
995
0
0
Northern Mass
Nov 4, 2005
#3
  • Nov 4, 2005
  • #3
hmmm... I'm confused as to where to start looking...
 

DTT92LX

New Member
Oct 28, 2003
185
1
0
Downingtown, PA
Nov 4, 2005
#4
  • Nov 4, 2005
  • #4
Here is a thread you should read...

http://forums.stangnet.com/showthread.php?t=571297
 

jaymac

New Member
Feb 18, 2004
995
0
0
Northern Mass
Nov 4, 2005
#5
  • Nov 4, 2005
  • #5
hey thanks for the link bro!
 

DTT92LX

New Member
Oct 28, 2003
185
1
0
Downingtown, PA
Nov 4, 2005
#6
  • Nov 4, 2005
  • #6
No problem. Just post back once you figger it out so other's will gain too...
 

jaymac

New Member
Feb 18, 2004
995
0
0
Northern Mass
Nov 7, 2005
#7
  • Nov 7, 2005
  • #7
welp, the one thing I can say is that when 5" vac. is applied to the nipple, it holds it and goes down steadily over 30 sec.
That sounds right, no?
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Nov 7, 2005
#8
  • Nov 7, 2005
  • #8
EGR test procedure courtesy of cjones

to check the EGR valve:
bring the engine to normal temp.
connect a vacuum pump to the EGR Valve
apply 5in vacuum to the valve.
if engine stumbled or died then EGR Valve and passage (there is a passageway through the heads and intake) are good.
if engine did NOT stumble or die then either the EGR Valve is bad and/or the passage is blocked.
if engine stumbled, connect vacuum gauge to the hose coming off of the EGR Valve
snap throttle to 2500 RPM (remember snap the throttle don't hold it there).
did the vacuum gauge show about 5in vacuum?

if not, check for manifold vacuum at the EGR vacuum valve.
if you have manifold vacuum then connect vacuum gauge to the EGR valve side of the vacuum valve and snap throttle to 2500 RPM.
should read about 5 in vacuum

Tell me which step you are at in the test proceedure
 

jaymac

New Member
Feb 18, 2004
995
0
0
Northern Mass
Nov 7, 2005
#9
  • Nov 7, 2005
  • #9
great thank you; I will go out after 3 pm and try it and post back -
Thanks again
 
You must log in or register to reply here.

Similar threads

Electrical Code 29 again
  • Creomod
  • Jul 31, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
392
Fox 5.0 Mustang Tech Aug 3, 2026
Creomod
J
Thanks for the information on codes 31,34,44 and 94!
  • JK86LX50
  • Mar 5, 2025
  • The Welcome Wagon
Replies
3
Views
377
The Welcome Wagon Aug 5, 2025
gkomo
S
Fuel ‘88 GT Runs Rich Cold — Fixes Itself When I Unplug Sensors (ECT, MAF, O2, etc.)
  • Sufarry
  • Nov 6, 2025
  • Fox 5.0 Mustang Tech
Replies
12
Views
1K
Fox 5.0 Mustang Tech Nov 9, 2025
Mustang5L5
T
Drivetrain TREMEC TKX 1–2 Grinding Issue at ~4,000 Miles + Poor Warranty/Customer Service Experience
  • Ttopfoxguy
  • Oct 10, 2026
  • Fox 5.0 Mustang Tech
Replies
5
Views
320
Fox 5.0 Mustang Tech Oct 15, 2026
JMG9350
J
Engine Random Misfire at idle.
  • Gulftown980x
  • Jul 29, 2026
  • SN95 4.6L Mustang Tech
Replies
11
Views
614
SN95 4.6L Mustang Tech Jul 31, 2026
squeak93
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?