• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

DART 347, new problems...questions!!

  • Thread starter Thread starter 1991vert
  • Start date Start date Jul 22, 2006

1991vert

10 Year Member
Feb 27, 2004
1,103
7
69
Ludlow, MA
Jul 22, 2006
#1
  • Jul 22, 2006
  • #1
ok so i got my shortblock back, finally, from the machine shop yesterday but i was too tired to touch it. i was planning on setting the lash today on the lifters/rockers and ran into a problem. first i got the dogbones on the passenger side of the engine and then when i went to put them on the drivers side, they dont fit. there is not enough vertical clearance to slide them on. so as i bowed my head in frustration i looked at the passenger side and noticed the dog bones weren't all sitting flat. the lifter came up too far out of the bore and the ring on the lifter pushes the dogbone up. that is the point where i went and got the noose and just quit.

i have heard of some "link-bar" lifters, but would those solve my problem(s)? are link-bar lifters the same as retrofit lifters? i'd prefer not having to fully break the bank with some $500 lifters. i just need something that will eliminate the dog bone and keep the lifters from rotating in the bore.


these say they're retrofit?

http://www.adperformance.com/index.php?main_page=index&cPath=191_192_195

these say link-bar

http://store.summitracing.com/partdetail.asp?part=CRN%2D36532%2D16&N=4294908331+4294840126+4294889096+4294908282+115&autoview=sku
 

Attachments

  • compcam_hydroller.webp
    5.9 KB · Views: 161
  • crn-36532-16_w.webp
    10.5 KB · Views: 173

1991vert

10 Year Member
Feb 27, 2004
1,103
7
69
Ludlow, MA
Jul 22, 2006
#2
  • Jul 22, 2006
  • #2
ttt
 
I

iapexl8r

Member
Apr 1, 2005
254
0
17
Jul 22, 2006
#3
  • Jul 22, 2006
  • #3
hmm need more info. late roller 5.0 block, early 302 late or early windsor ?????? small base cam or factory 5.0 roller replacenent.are you talking about the rollers in the pic
 

1991vert

10 Year Member
Feb 27, 2004
1,103
7
69
Ludlow, MA
Jul 22, 2006
#4
  • Jul 22, 2006
  • #4
it's a dart sportsman block. 302. e-cam. i dont think the cam should matter though

edit: they were FMS stock replacement lifters i had in there when trying to put the dogbones in.
 

1991vert

10 Year Member
Feb 27, 2004
1,103
7
69
Ludlow, MA
Jul 22, 2006
#5
  • Jul 22, 2006
  • #5
hopefully someone with some knowledge will chime in...

hoping rick91gt will
 

1991vert

10 Year Member
Feb 27, 2004
1,103
7
69
Ludlow, MA
Jul 22, 2006
#6
  • Jul 22, 2006
  • #6
thank you for all of the responses!

no but seriously, no one has a clue what im talking about?
 

bob331T76

New Member
Aug 28, 2005
76
0
0
so cal
Jul 22, 2006
#7
  • Jul 22, 2006
  • #7
drop a pm to dagger... i have no idea sorry
 

1991vert

10 Year Member
Feb 27, 2004
1,103
7
69
Ludlow, MA
Jul 22, 2006
#8
  • Jul 22, 2006
  • #8
you have a dart sportsman...what lifters are you running? stock? or link-bar?
 

GroverDill

GoldMember
Founding Member
Aug 18, 1999
5,442
1,490
214
Demotte IN 46310
Jul 22, 2006
#9
  • Jul 22, 2006
  • #9
Sportsman use stock lifters.
Iron Egale use the link bar style.



From the Dart site.
Q: What is the difference betwen the Iron Eagle Ford Block and the Sportsman Block?
A: The Ford Sportsman Block is a lower cost option based on the same casting as the Iron Eagle. It will accept the stock lifters and spider. It does not include cam bearings, freeze plugs or dowels, and it has two-bolt front and rear main caps with four-bolt centers. Available as 302 w/8.200" Deck or 351 w/9.500" deck height. The Iron Eagle Block has four-bolt main caps and includes coated cam bearings, freeze plugs and dowels. It requires aftermarket lifters and is available as 302 w/8.200" or 8.700" deck and 351 w/9.200" or 9.500" deck height.
 

1991vert

10 Year Member
Feb 27, 2004
1,103
7
69
Ludlow, MA
Jul 22, 2006
#10
  • Jul 22, 2006
  • #10
ya but the dogbones dont have any room to be put on. there's not enough space between the lifter and the lifter valley sidewall. there are notches though. the lifter also pushes up on the dogbone when the cam lobe is at full lift
 

bluevenom867

I will have images of molesting stuffed animals in
Dec 15, 2003
1,704
1
0
St.Petersburg,FL
Jul 22, 2006
#11
  • Jul 22, 2006
  • #11
Go link-bar,they are better quality lifters anyhow.
 

1991vert

10 Year Member
Feb 27, 2004
1,103
7
69
Ludlow, MA
Jul 23, 2006
#12
  • Jul 23, 2006
  • #12
i shouldnt have a problem running them, right? do you adjust them the same way you would with a traditional lifter? (setting the rocker lash)
 

1991vert

10 Year Member
Feb 27, 2004
1,103
7
69
Ludlow, MA
Jul 23, 2006
#13
  • Jul 23, 2006
  • #13
well just to show everyone what my situation is, here's a few pictures...



 

bob331T76

New Member
Aug 28, 2005
76
0
0
so cal
Jul 23, 2006
#14
  • Jul 23, 2006
  • #14
1991vert said:
you have a dart sportsman...what lifters are you running? stock? or link-bar?
Click to expand...

Yeah im running Crane Hydraulic Roller Lifters (Link Bar Type)
$$$ well spent too !
 
K

Kaoz78

New Member
Jun 8, 2006
8
0
0
Jul 23, 2006
#15
  • Jul 23, 2006
  • #15
I can't really offer anything to the original poster as far as info but, I would send those pics to Dart. Ask them what's wrong.
 

1991vert

10 Year Member
Feb 27, 2004
1,103
7
69
Ludlow, MA
Jul 23, 2006
#16
  • Jul 23, 2006
  • #16
i found this post

http://bbs.hardcore50.com/vbulletin/showthread.php?t=29389&highlight=dart+sportsman+block

so i guess it's not just me and it's a common problem..
 
You must log in or register to reply here.

Similar threads

R
Help Needed! 95 5.0
  • Riley McCallum
  • Aug 30, 2018
  • Fox 5.0 Mustang Tech
Replies
4
Views
8K
Fox 5.0 Mustang Tech Aug 30, 2018
Riley McCallum
R
Old H/c/i Installation Explanation And Pics
  • FastDriver
  • Jan 26, 2018
  • Fox 5.0 Mustang Tech
Replies
5
Views
2K
Fox 5.0 Mustang Tech Jan 27, 2018
FastDriver
351w F4 Block Camshaft
  • sharp2377
  • Oct 10, 2015
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
3
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 10, 2015
A5literMan
Engine 1991 Lx 5.0 Engine Rebuild Kit Inquiry
  • HotRodBlack
  • Apr 28, 2017
  • Fox 5.0 Mustang Tech
Replies
3
Views
2K
Fox 5.0 Mustang Tech Apr 29, 2017
HotRodBlack
Strange engine noise?
  • MikeUrban
  • Jan 15, 2013
  • Fox 5.0 Mustang Tech
Replies
17
Views
1K
Fox 5.0 Mustang Tech Feb 14, 2013
7991LXnSHO
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?