• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Desparately Need Help!!!

  • Thread starter Thread starter Mikey1968
  • Start date Start date Oct 13, 2005

Mikey1968

Member
Nov 1, 2003
232
0
17
Kommiefornia
Oct 13, 2005
#1
  • Oct 13, 2005
  • #1
Vehicle: Stock 89 Mustang GT, about 150,000 miles.

Problem: With less than half tank of gas, 'Stang will feel like it won't take the gas during a turn. You can push accelerator and no increase in power. Slight and slow drop of rpm, not sudden. Then, all will be fine and it will accelerate. Occasionally it will even stall.

What's been done:
Cleaned EGR, IAC, throttle and MAF sensor and connectors.
New rebuilt distributor with new ignition module, cleaned connectors
New fuel pump and cleaned connectors.
New cap, rotor and Ford racing wires.
New EGR position sensor.
New fuel filter.
Checked for water in gas and ran a bottle of dryer through.
Measured fuel pressure, is in spec for idle but almost 5 psi low with key on engine off as the shop manual says this should be 5 psi higher than at idle.
Checked fuel pressure regulator for leaks, none.
Cleaned the "salt/pepper" connectors.
Visually inspected for vacuum leaks.
Checked the TPS with digital at both extremes and analog throughout the sweep with no drop outs.
Checked throttle cable for binding.
Checked fuel pump relay, harnesses and inertia switch by wiggle-test, all OK.
Wiggle-tested fuel pump harness on top of fuel tank.
Pressed the inertia switch button just to be sure.
Codes set: 67 (Neutral safety circuit failure)with 95 (Fuel pump secondary circuit failure when the PCM commanded the fuel pump on, voltage was not detected on FPM) in continuous memory. Don't know why 67 is set unless the un-used switch I found when I put in the new 93-spec'd T5 transmission has something to do with it.

I'm just about to sell the POS if it can't be fixed! I've been messing with this most of this year. I've never had a car beat me but this one has me and all my buddies at a loss. Please, give me some ideas of what to check. I plan on troubleshooting the 95 code (Fuel pump secondary circuit) in full this weekend.

The 89 Mustang used to be the most reliable car we owned. It's in nearly perfect condition and would really hate to roll it over a cliff. It has about 150,000 miles.

PLEASE HELP!
Mikey
 

srothfuss

Last night I stabbed the same guy 7 times in a row
Oct 17, 2004
1,796
3
0
Woodward Ave.
Oct 13, 2005
#2
  • Oct 13, 2005
  • #2
Maybe your fuel pump is dying..?

Or a baffle in the tank is missing which allows your gas to slosh around when you are taking corners.
 

Mikey1968

Member
Nov 1, 2003
232
0
17
Kommiefornia
Oct 13, 2005
#3
  • Oct 13, 2005
  • #3
I thought of the fuel pump being bad. That's why I checked the fuel pressure at idle and I did also check it by reving the engine. Don't the pumps usually work or not?

What baffles would come loose? Are there some? I looked in the tank when I repaired my fuel sending unit and put in the new pump. Didn't notice anything odd.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Oct 13, 2005
#4
  • Oct 13, 2005
  • #4
The problem with your static FP testing is that this is when the car runs fine, right? You would need to be able to test pressure while making the turn that makes your car run like poop.
It seems to me that a few folks have had similar G-related issues and it was the sock on the FP. I dont say that to prompt you to run out and try swapping pumps, but only toss it out as fodder for others to say yes or no to.

I still think it is pump )(or tank - I have not had broken baffle experience) related since it only happens when you are at a lower level in the tank. If you clear codes, does 95 come back? That one is often a ghost code, except I give it creed given your issues (like the intertia switch is taking a slight dump under turning. That still does not explain the fuel level being meaningful, so nix the inertia switch idea).

Short of parking on some goofy bank and checking FP then (if that would even be a valid test, I know not), I cant think of much. That low fuel level and pump seem to go hand-in-hand though.

I dont know if the 93 T5 has a NSS or not. Also be sure the A/C is off (that will also trip it IIRC).

Good luck and hang in there. It might simply be a FP or another simple issue.
 

Mikey1968

Member
Nov 1, 2003
232
0
17
Kommiefornia
Oct 14, 2005
#5
  • Oct 14, 2005
  • #5
HISSIN50 said:
The problem with your static FP testing is that this is when the car runs fine, right? You would need to be able to test pressure while making the turn that makes your car run like poop.
It seems to me that a few folks have had similar G-related issues and it was the sock on the FP. I dont say that to prompt you to run out and try swapping pumps, but only toss it out as fodder for others to say yes or no to.

I still think it is pump )(or tank - I have not had broken baffle experience) related since it only happens when you are at a lower level in the tank. If you clear codes, does 95 come back? That one is often a ghost code, except I give it creed given your issues (like the intertia switch is taking a slight dump under turning. That still does not explain the fuel level being meaningful, so nix the inertia switch idea).

Short of parking on some goofy bank and checking FP then (if that would even be a valid test, I know not), I cant think of much. That low fuel level and pump seem to go hand-in-hand though.

I dont know if the 93 T5 has a NSS or not. Also be sure the A/C is off (that will also trip it IIRC).

Good luck and hang in there. It might simply be a FP or another simple issue.
Click to expand...

Tell me more on the broken baffle idea. Two new ideas have been put forward. Ford had problems with the baffle in other models, I've been told, and had some TSB or recall due to baffles. Tank/pump/baffles are the same as this model and the plastic baffle had holes in line so would cause problems in a right turn. New one had holes staggered. Other idea is balled up "ginger ale" colored stuff caused by the new "improved" gas dissolving the gas tank sealant. Ever heard of these????

I cleared codes, had wifey drive it, had 4 failures, code 95 set. Haven't tried it again....kinda want to stay married. It's really her car.

What do you think????
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Oct 14, 2005
#6
  • Oct 14, 2005
  • #6
Mikey, Srothfuss had the baffle info, not me. We will wait for his reply.

If you keep getting a code 95, I would really be focusing on the electrical side of the fuel pump, not the pump itself.

SInce it is an intermittant issue, it will be hard to trace (unless you can get a meter on the FP relay when the car stops running).

If inertia switches are cheap, I would swap it to see if it helps. Jrichker has long posts about troubleshooting the FP electrical system. I had outlined much of the pertinant aspects as I know them, but the server here decided not to take my long-winded first reply. I will be more brief this time (ano not cover that - nothing more irritating than typing out a page long reply to have it not take).

One can jump the inertia switch, but I would not do this given your issues and the fact that your better half drives the car.

Good luck Mikey.
 

iskwezm

10 Year Member
May 24, 2005
4,159
20
79
Rowland Heights,California
Oct 15, 2005
#7
  • Oct 15, 2005
  • #7
do as somebody said and check your fuel pressure while driving to give you a idea od whats actually happening.We used to run a guage to the windshield and watch as we drive,or we acces to the NGS tester to datalog.
 

srothfuss

Last night I stabbed the same guy 7 times in a row
Oct 17, 2004
1,796
3
0
Woodward Ave.
Oct 15, 2005
#8
  • Oct 15, 2005
  • #8
Mikey1968 said:
Tell me more on the broken baffle idea. Two new ideas have been put forward. Ford had problems with the baffle in other models, I've been told, and had some TSB or recall due to baffles. Tank/pump/baffles are the same as this model and the plastic baffle had holes in line so would cause problems in a right turn. New one had holes staggered. Other idea is balled up "ginger ale" colored stuff caused by the new "improved" gas dissolving the gas tank sealant. Ever heard of these????

I cleared codes, had wifey drive it, had 4 failures, code 95 set. Haven't tried it again....kinda want to stay married. It's really her car.

What do you think????
Click to expand...

(sorry for the delayed reply guys)


Many things can happen inside the gas tank. Since it's so hard to look at, we never really give it a thought (or at least we put it to the end of the, 'I'll check that list')

Inside the tank are a series of walls (baffles) that help keep the gas in contact with the fuel pickup through all types of driving. These walls can (not often, but can) come apart from the inside of the tank. Which would allow your gas to slosh away for the pickup and cause your fuel starvation problems. Then again, sometimes the inside of the tank is just dirty. maybe a piece of debris is resting on that one side of your pickup and as you take a corner, the gas carries it over to the pickup and causes your issue. The only way to really know if this is happening in your car, is to run the tank to empty (or close) and drop it. Once you have the tank out, you will need to get out the rest of the fuel or most of it and use a flashlight to look inside. You can also try tipping the tank to listen for anything sliding around in there.

Causes: Accidents are the main cause of loose baffles. Sometimes though, they just come loose with age (driving over railroad tracks, bumpy roads, etc.) all introduce vibrations into the vehicle which can shake parts like this loose.


Now, that is a lot of work just to 'see' if there is something wrong or inside your tank. I would start by eliminating the other variables, like the FP regulator first before you go through all of that trouble.

I liked someones idea of putting the car up on it's side and checking the FP while the car is running (in your driveway with jack stands of course) to help you begin the diagnosis. You would then beable to determine what is going on with your fuel. Also, if the pressure drops below norms while the car is just running (on all 4 wheels / not tipped up) than the baffle might not be your issue.


Good luck, let me know if you have anymore questions (stinking gas tanks!) -Steve
 

Mikey1968

Member
Nov 1, 2003
232
0
17
Kommiefornia
Oct 15, 2005
#9
  • Oct 15, 2005
  • #9
OK. Here's my strategy for now:

I'm assuming a intermittent fuel pressure drop.

First, troubleshoot electrical stuff related to Code 95 which is the control circuit not the power circuit. Then check some simple stuff like maybe adding a firewall ground wire in conjunction with the stock one. Another look at obvious stuff. Perhaps resetting the computer by removing the battery power over night. Intermittent is usually electrical in nature. That will burn the weekend.

Then, I will troubleshoot mechnical things related to a pressure drop. Pressure regulator...anything simple like that. Then, drop the tank and have a look.

For help, I need to know the failure symptom for the pressure regulator. Also, educate me on the baffles. How are they held in? How do you replace a bad one? What do I look for? What is the construction of a properly mounted baffle?

Let me know on my questions and I might be able to get to it this weekend. I promise ot announce my victory!
Thanks,
Mikey
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Oct 15, 2005
#10
  • Oct 15, 2005
  • #10
The computer codes will clear if you simply disconnect the jumper while the computer is dumping them. This won't hurt anything and will preserve the "learned settings".

The baffles are normally spot welded in place. As you have probably seen, sometimes the spot welds break.

Here's the troubleshooting test path for 86-90 Model Mustang fuel pump problems.

Fuel Pump Troubleshooting for 86-90 Mustangs

Clue – listen for the fuel pump to prime when you first turn the ignition switch on. It should run for 5-20 seconds and shut off. To trick the fuel pump into running, find the ECC test connector and jump the connector in the lower RH corner to ground. See http://www.mustangworks.com/article...c-iv_codes.html for a description of the test connector. If the relay & inertia switch are OK, you will have power to the pump. Check fuel pressure – remove the cap from the schrader valve behind the alternator and depress the core. Fuel should squirt out, catch it in a rag. A tire pressure gauge can also be used if you have one - look for 37-40 PSI. Beware of fire hazard when you do this.

No fuel pressure, possible failed items in order of their probability:
A.) Tripped inertia switch – press reset button on the inertia switch. The hatch cars hide it under the plastic trim covering the driver's side taillight. Use the voltmeter or test light to make sure you have power to both sides of the switch
B.) Fuel pump power relay – located under the driver’s seat in most stangs built before 92. On 92 and later model cars it is located below the Mass Air Flow meter.
C.) Clogged fuel filter
D.) Failed fuel pump
E.) Blown fuse link in wiring harness.
F.) Fuel pressure regulator failed. Remove vacuum line from regulator and inspect for fuel escaping while pump is running.

The electrical circuit for the fuel pump has two paths, a control path and a power path.

Control path
The control path consists of the inertia switch, the computer, and the fuel pump relay coil. It turns the fuel pump relay on or off under computer control. The switched power (red wire) from the ECC relay goes to the inertia switch (red/black wire) then from the inertia switch to the relay coil and then from the relay coil to the computer (tan/ Lt green wire). The computer provides the ground path to complete the circuit. This ground causes the relay coil to energize and close the contacts for the power path. Keep in mind that you can have voltage to all the right places, but the computer must provide a ground. If there is no ground, the relay will not close the power contacts.

Power path
The power path picks up from a fuse link near the starter relay. Fuse links are like fuses, except they are pieces of wire and are made right into the wiring harness. The feed wire from the fuse link (orange/ light blue wire) goes to the fuel pump relay contacts. When the contacts close because the relay energizes, the power flows through the contacts to the fuel pump (light pink/black wire). The fuel pump has a black wire that supplies the ground to complete the circuit.

Remember that the computer does not source any power to actuators, relays or injectors, but provides the ground necessary to complete the circuit. That means one side of the circuit will always be hot, and the other side will go to ground or below 1 volt as the computer switches on that circuit.

See the following website for some help from Tmoss (diagram designer) & Stang&2Birds (website host)

http://www.veryuseful.com/mustang/t...witchWiring.gif

http://www.veryuseful.com/mustang/t...inks-ign-ac.gif

http://www.veryuseful.com/mustang/t...91eecPinout.gif

Now that you have the theory of how it works, it’s time to go digging.

Power path
Look for 12 volts at the Orange/Lt. Blue wire (power source for fuel pump relay). No voltage or low voltage, bad fuse link, bad wiring, bad ignition switch or ignition switch wiring or connections. There is a mystery connector somewhere under the driver’s side kick panel, between the fuel pump relay and the fuse link.

Turn on the key and jumper the fuel pump test connector to ground as previously described. Look for 12 volts at the Light Pink/Black wire (relay controlled power for the fuel pump). No voltage there means that the relay has failed, or there is a broken wire in the relay control circuit.

Control path
Check the Red/black wire, it should have 12 volts. No 12 volts there, either the inertia switch is open or has no power to it. Check both sides of the inertia switch: there should be power on the Red wire and Red/Black wire. Power on the Red wire and not on the Red/Black wire means the inertia switch is open.

The Tan/Lt Green wire provides a ground path for the relay power. With the test connector jumpered to ground, there should be less than .75 volts. Use a test lamp with one side connected to battery power and the other side to the Tan/Lt Green wire. The test light should glow brightly. No glow and you have a broken wire or bad connection between the test connector and the relay. To test the wiring from the computer, remove the passenger side kick panel and disconnect the computer connector. It has a 10 MM bolt that holds it in place. With the test lamp connected to power, jumper pin 22 to ground and the test lamp should glow. No glow and the wiring between the computer and the fuel pump relay is bad.

If all of the checks have worked OK to this point, then the computer is bad. The computers are very reliable and not prone to failure unless there has been significant electrical trauma to the car. Things like lightning strikes and putting the battery in backwards or connecting jumper cables backwards are about the only thing that kills the computer.
 

Mikey1968

Member
Nov 1, 2003
232
0
17
Kommiefornia
Oct 15, 2005
#11
  • Oct 15, 2005
  • #11
Absolutely excellent write up! I printed it out to use today. Just wanted to let you know all your links are dead.

I wanted to clear the computer of all learned settings in case something learned was causing this. I have one of th ecode readers and cleared the codes once already to get the 95 and 67.

Don't know why 67 gets set. I'm assuming it's an error or ghost setting.

Again, THANKS!!!!
Mikey
 

Mikey1968

Member
Nov 1, 2003
232
0
17
Kommiefornia
Oct 15, 2005
#12
  • Oct 15, 2005
  • #12
OK, tried some things and failed miserably.

I cleared the codes, reset the throttle idle setting and took the stupid thing for a test ride. Got new failure modes now...

The thing would stall only in right turns. First time the engine continued to run but again wouldn't take the gas. Then it would snap back to normal. Then it completely stalled after another right turn and would not restart until 15 minutes. Tried restarting multiple times. I could hear the fuel pump start for the two seconds each time. Starter and battery was very strong. Had a tow truck on the way and had to cancel. Started to drive home, then, another right turn caused it to completely stall again, then it would restart in a few seconds and nearly stall again. Then, it all cleared up and I made it home even with another two right turns. New codes are 96 and 87 both pointing to the fuel pump secondary (control) circuit. Codes have to be wrong as the pump fired up EVERY time I turned the key on. You could hear it in the back!

It acted fine idling at the house so I jacked up the right side to make the fuel slosh like a right turn and all was good. Double checked the inertia switch ohms and it showed zero ohms. I checked the connections at the coil, the starter relay, the MAP sensor and checked the cap, rotor and coil wire at both ends. I now figure the fuel pump circuits are fine and am thinking the rebuilt distributor I put in might have a bad ignition module. So, I put in the original Motorcraft ignition module and called it a day. It's raining and the temp dropped like a rock. Will test drive when I'm not so mad.

Question...what's the proper way to set the mechanical idle?

Any new ideas?
 

Mikey1968

Member
Nov 1, 2003
232
0
17
Kommiefornia
Oct 23, 2005
#13
  • Oct 23, 2005
  • #13
Ok....I dropped the fuel tank and found two things wrong. The fuel pump rubber check valve for the return line was knocked off and the baffle was rattling around (may have knocked off the valve). I think I have my problem solved. New gas tank from Mustangs Unlimited for $120 + shipping.
Mikey
 
You must log in or register to reply here.

Similar threads

M
01 mustang 3.8 fuel pressure issue
  • Mhaley2006
  • May 29, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
4
Views
535
1996 - 2004 SN95 Mustang -General/Talk- Aug 9, 2026
JohnKay
J
F
2004 Mustang GT – Fuel Pump Not Priming
  • Fayio
  • Apr 22, 2026
  • SN95 4.6L Mustang Tech
Replies
7
Views
542
SN95 4.6L Mustang Tech Apr 27, 2026
n0v8or
N
C
Electrical Fuel Gauge...Help! What did I do or Didn't Do?
  • ChickenDeluxe
  • Sep 3, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
246
Fox 5.0 Mustang Tech Sep 3, 2026
ChickenDeluxe
C
1
Engine 91 mustang 302 Low acceleration car backfires pops and acts like it doesn’t want to take fuel
  • 1991Fox5.0
  • Oct 4, 2025
  • Fox 5.0 Mustang Tech
Replies
16
Views
1K
Fox 5.0 Mustang Tech Oct 6, 2025
1991Fox5.0
1
Resolved 93 Mustang 5.0 - Cranks but does not start
  • dan50
  • Jul 18, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
480
Fox 5.0 Mustang Tech Jul 18, 2026
dan50
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?