• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Differential Removal

  • Thread starter Thread starter Deleted member 87397
  • Start date Start date Mar 15, 2008
D

Deleted member 87397

Mar 15, 2008
#1
  • Mar 15, 2008
  • #1
Hey I have the whole rearend out of the car and I'm trying to remove the diff/gears so
I can get the axle tubes welded and the whole housing powdercoated before I rebuild it. I've never removed one before I'm looking for a good write up or directions on how to get the diff out. I have the pinion shaft out and the axles removed. I have the nut removed from the pinion gear on the outside of the rearend housing, and the bearing caps are removed. What do I do now to get the whole unit out? I'm putting in an Auburn posi but I want to reuse the gears since they are in great shape and I don't want to kill anything getting the diff out. Thanks.
 

89streetbeast

New Member
Dec 4, 2006
365
1
0
horton,ks
Mar 15, 2008
#2
  • Mar 15, 2008
  • #2
when i took the old gears out of the 89 i just used a prybar with a rag on the end, stuck it in the diff and pryed. popped right out
 

montyd

Member
Mar 13, 2006
114
3
19
Mar 15, 2008
#3
  • Mar 15, 2008
  • #3
i second that
 
D

Deleted member 87397

Mar 15, 2008
#4
  • Mar 15, 2008
  • #4
I'll have to go buy a pry bar and see if i can get it. I tried using my breaker bar as a pry bar, but it doesn't have enough length on it. It just seems like the bearings are stuck in the grooves and won't budge.
 
D

Deleted member 87397

Mar 15, 2008
#5
  • Mar 15, 2008
  • #5
Ok i bought a pry bar and used it and the diff. popped right out. Thanks for the help guys. Now, do I need to do anything special to get the pinion gear out? Or will a couple good whacks with a hammer/mallet do the trick?
 

89streetbeast

New Member
Dec 4, 2006
365
1
0
horton,ks
Mar 15, 2008
#6
  • Mar 15, 2008
  • #6
mine just fell out cuz the bearing was weak lol. might have to use maybe a rubber mallet or one of them plastic dead blow hammers. should pop right out. but make sure you dont hit it too hard and it flys out and does some carnage to the splines.
 
D

Deleted member 87397

Mar 15, 2008
#7
  • Mar 15, 2008
  • #7
I finally got it out. It was stuck in there like a mother. The last person to install the gears etc on this thing did a really nice job. The whole rear end has now been completely disassembled. Next week I'm going to get the axle tubes on the outside and the control arm mounts welded up a bit better and then take the whole thin in for sandblasting and powder coating. I'll have to post pics when it's done.
 
You must log in or register to reply here.

Similar threads

S
Differential noise over bumps
  • sharkrat
  • Apr 10, 2026
  • 2005 - 2009 Specific Tech
Replies
3
Views
289
2005 - 2009 Specific Tech Jun 18, 2026
TPony
D
Drivetrain car still rolling while in gear and off
  • dqureshi06
  • Jan 24, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
328
Fox 5.0 Mustang Tech Jan 24, 2026
General karthief
J
2004 Mustang 3.8L V6 vibrations above 65 MPH and differential leaks
  • joeybuddy96
  • Mar 16, 2026
  • SN95 V6 Mustang Tech
Replies
17
Views
1K
SN95 V6 Mustang Tech Aug 29, 2026
joeybuddy96
J
3.08 gears with a manual trans
  • limp
  • Aug 27, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2 3
Replies
43
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 14, 2026
Qtrhrse23
Drivetrain Broken clutch cable- what it looks like
  • JulianR
  • Aug 6, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
24
Views
887
Fox 5.0 Mustang Tech Aug 10, 2026
gkomo
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?