• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Distributor off?

  • Thread starter Thread starter kpack5982
  • Start date Start date Mar 4, 2007

kpack5982

Yeah, it was pretty stiff, but eventually a buddy
Jul 13, 2005
325
1
19
Granger, IA
Mar 4, 2007
#1
  • Mar 4, 2007
  • #1
After playing around trying to get my car started after heads/cam swap I finally got it running. Distributor was 180 off. Problem now is that it slowly starts to idle down until it dies. When I turn the distributor clockwise to advance it all the way it starts up much better and won't start at all if i retard it (turn it counter-clockwise). Would the distributor being off a tooth cause this problem? Like if I took it out and moved the rotor counter-clockwise like one tooth, that would be the right way, right? It wouldn't hurt the engine would it if that's not the problem?
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,378
18,123
224
Massachusetts
Mar 4, 2007
#2
  • Mar 4, 2007
  • #2
More than likely that is your problem. The intake gets in the way of the dist and it can't spin all the way around. So the trick is to stab the dist. in a spot where your range of spin will put you in the correct range to set the timing.

Sometimes you'll notice it will run better as you turn it only to find the intake manifold is in the way.

That's when you need ot move it one tooth over and try again. Try using a timing light as well to make sure you really are off on the timing
 

kpack5982

Yeah, it was pretty stiff, but eventually a buddy
Jul 13, 2005
325
1
19
Granger, IA
Mar 4, 2007
#3
  • Mar 4, 2007
  • #3
That's kinda what I thought. problem is the car wont' stay running long enough for me to get out after starting it and get to the timing light. No one wanted to help me out so I was all by my lonesome.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Mar 4, 2007
#4
  • Mar 4, 2007
  • #4
I'd agree also. As Mike said, restab it so the TFI harness is in about the middle of the road when you're around 10* - that gives you room to play.

Good luck.
 

04sleeper

Founding Member
Jun 22, 2002
2,674
14
89
Dallas, TX
Mar 5, 2007
#5
  • Mar 5, 2007
  • #5
I have always pulled out the number 1 spark plug and checked for the compression stroke of the cylinder with my finger by slowly turning the motor over by hand with a socket on the crank bolt.

It should be at TDC and the timing mark will be on "0". Then I stab the dizzy with the TFI facing me and the rotor facing #1 on the cap.

To get a good start point for timing I usually line up the mark on the distributor with the line on the groove on the block.

I have hit it perfectly on a number of occasions with 10 degrees timing.

Another tip is to stab the dizzy a little counterclockwise to where you want it to end up because when you stab it, it will rotate clockwise when meshing with the cam gear.
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Mar 5, 2007
#6
  • Mar 5, 2007
  • #6
You guys have danced around this a little bit, so I just wanted to bring it up for discussion...

You can have the dist 'a tooth off' and this can cause some issues with injector timing. I'm not sure if that is the issue here or not though.

I have no idea how you would get around this with the interference issues common to the Cobra lower...???

As JT stated, the dist should be 'middle of the road' at 10*


jason
 
You must log in or register to reply here.

Similar threads

Distributor installed wrong
  • djj62478
  • Jun 14, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
352
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 21, 2026
CAMTWO1070
Brakes FOX BRAKES ISSUES
  • PonyGTrider
  • Jan 11, 2026
  • Fox 5.0 Mustang Tech
  • 2 3
Replies
53
Views
3K
Fox 5.0 Mustang Tech Jan 31, 2026
Mustang5L5
F
Fox 1990 Mustang GT 5.0 A9L – Engine suddenly shuts off but immediately restarts when key turned
  • FishermansFriend
  • Aug 9, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
16
Views
702
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 30, 2026
General karthief
A
1987 5.0 speed density Foxbody crank no start
  • Alan2204
  • May 23, 2026
  • Fox 5.0 Mustang Tech
Replies
10
Views
602
Fox 5.0 Mustang Tech May 30, 2026
Mcmahst
B
Electrical Why does my fox body keep frying eecs
  • brandyn200
  • Jun 20, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
533
Fox 5.0 Mustang Tech Jun 25, 2026
AeroCoupe
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?