• Mustang Forums
  • 1965 - 1973 Classic Mustangs -General/Talk-
  • Classic Mustang Specific Tech

Door And Vent Window

  • Thread starter Thread starter iggy
  • Start date Start date Oct 24, 2013
I

iggy

New Member
Oct 15, 2003
14
0
2
Oct 24, 2013
#1
  • Oct 24, 2013
  • #1
i have a 67 fastback,im having trouble adjusting the window and vent window,do you adjust the vent first or the window first. i put new seals in and new window regulators in and greased them up good.they roll up and down pretty good with door open but when door is closed they roll down good but rolling them up they get hard and harder the last couple of inches, if i readjust them then the back part of window buy the handle rubs on the door. iv spent hours trying. one thing i notice the adjusting screws the one for an allen wrench are a little different in length does it matter which one goes where
thank you
__________________
1967 fastback 289 auto
 

horse sence

15 Year Member
Nov 29, 1999
12,187
8,009
233
Wile Coyote's stunt double
Oct 24, 2013
#2
  • Oct 24, 2013
  • #2
iggy said:
i have a 67 fastback,im having trouble adjusting the window and vent window,do you adjust the vent first or the window first. i put new seals in and new window regulators in and greased them up good.they roll up and down pretty good with door open but when door is closed they roll down good but rolling them up they get hard and harder the last couple of inches, if i readjust them then the back part of window buy the handle rubs on the door. iv spent hours trying. one thing i notice the adjusting screws the one for an allen wrench are a little different in length does it matter which one goes where
thank you
__________________
1967 fastback 289 auto
Click to expand...
the large headed adjuster goes to the top part of the wind wing the small one goes to the bottom of the slide track.the wind wing and the door glass should be adjusted at the same time. you may have the top of the glass in the back to far in and it is dragging the rubber.check the vent window ,it should have an even spacing all the way up with the stainless that the rubber pushes into.
 
You must log in or register to reply here.

Similar threads

Help! Problem with replacment window regulator motor
  • TTSaleen
  • Oct 24, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
5
Views
282
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 24, 2025
General karthief
G
Intro and FB questions
  • gflat65
  • Nov 16, 2025
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
1
Views
193
1965 - 1973 Classic Mustangs -General/Talk- Nov 25, 2025
horse sence
P
2012 Mustang window problems
  • pearlguerra
  • Aug 16, 2024
  • 2005 - 2014 S-197 Mustang -General/Talk-
Replies
2
Views
546
2005 - 2014 S-197 Mustang -General/Talk- Aug 17, 2024
Neko-
S
1989 Passenger side electric window issue
  • Sanchez_005150
  • Jul 17, 2024
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
10
Views
977
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 4, 2025
WillWho?
W
Thinking of looking at this 67 coupe. Looking for some opinions.
  • billison
  • Aug 11, 2024
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
10
Views
1K
1965 - 1973 Classic Mustangs -General/Talk- Aug 28, 2024
89ripper
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1965 - 1973 Classic Mustangs -General/Talk-
  • Classic Mustang Specific Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?