ECT Sensor, unplugged?

jabGT

New Member
Mar 11, 2004
59
0
0
Michigan
I trying to hunt down my pinging/detonation problem(running N/A). I unplugged my ECT sensor and took it for a quick spin (also watching my temp) no detonation, was able to run 14* base timing before couldn't even run 8*. The car felt like it ran much better. My question what affect will the ECT sensor unplugged have on the computer advanced timing? Wil it still advance timing tables, or just not as much? Just kinda of courious what to expect with a new sensor. Also I have had a hot start problem, but with the sensor unplugged it is much better? Anybody have any experience with this?

Thanks
 
jabGT said:
I trying to hunt down my pinging/detonation problem(running N/A). I unplugged my ECT sensor and took it for a quick spin (also watching my temp) no detonation, was able to run 14* base timing before couldn't even run 8*. The car felt like it ran much better. My question what affect will the ECT sensor unplugged have on the computer advanced timing? Wil it still advance timing tables, or just not as much? Just kinda of courious what to expect with a new sensor. Also I have had a hot start problem, but with the sensor unplugged it is much better? Anybody have any experience with this?

Thanks

It sounds like you just need a new ECT sensor. If you do that (it's only like $15 at Autozone) I think you'll notice an improvement over just running without the old one plugged it.
 
Here's the test path to check your ECT sensor. Use it and save a few $$$ for use on other things...

Code 21 – ECT sensor out of range. Broken or damaged wiring, bad ECT sensor. Note that that if the outside air temp is below 50 degrees F that the test for the ECT can be in error.

The ACT & ECT have the same thermistor, so the table values are the same

ACT & ECT test data:

Use Pin 46 on the computer for ground for both ECT & ACT to get most accurate readings.

Pin 7 on the computer - ECT signal in. at 176 degrees F it should be .80 volts

Pin 25 on the computer - ACT signal in. at 50 degrees F it should be 3.5 volts. It is a good number if the ACT is mounted in the inlet airbox. If it is mounted in the lower intake manifold, the voltage readings will be lower because of the heat transfer.

Voltages may be measured across the ECT/ACT by probing the connector from the rear. Use care in doing it so that you don't damage the wiring or connector.

Here's the table :

68 degrees F = 3.02 v
86 degrees F = 2.62 v
104 degrees F = 2.16 v
122 degrees F = 1.72 v
140 degrees F = 1.35 v
158 degrees F = 1.04 v
176 degrees F = .80 v
194 degrees F = .61

Note that all resistance tests must be done with power off. Measuring resistance with a circuit powered on will give false readings and possibly damage the meter.

Ohms measures at the computer with the computer disconnected, or at the sensor with the sensor disconnected.
50 degrees F = 58.75 K ohms
68 degrees F = 37.30 K ohms
86 degrees F = 27.27 K ohms
104 degrees F = 16.15 K ohms
122 degrees F = 10.97 K ohms
140 degrees F = 7.60 K ohms
158 degrees F = 5.37 K ohms
176 degrees F = 3.84 K ohms
194 degrees F = 2.80 K ohms
 
I pulled the sensor and tested it in hot water, at 180 to 190* I was getting roughly 4.5-5.5K ohms so I would say that it is slighly out of range. I'll pick up a new on today.

Thanks for the help.