• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Engine Bay Help

  • Thread starter Thread starter marine_2003
  • Start date Start date Oct 8, 2005

marine_2003

Member
Jun 6, 2005
427
0
16
Lake County, FL
Oct 8, 2005
#1
  • Oct 8, 2005
  • #1
Here is a pic of my engine bay, I want to clean up and get rid of all the wiring that i can. Its carburated, has the stock computer, but i dont hink that i need half of the wiring that it has since i have started switching out my gauges from stock to Autometer Ultralite. I know that i need the wires for my ignition, but i think that that should be it right? Proably the wires for the blinkers and lights, and for my cooling fan relay.

Thanks

Anthony
 

hllon4whls

BANNED
Founding Member
Jan 17, 2002
2,567
0
46
Covington
Oct 8, 2005
#2
  • Oct 8, 2005
  • #2
marine_2003 said:
Here is a pic of my engine bay, I want to clean up and get rid of all the wiring that i can. Its carburated, has the stock computer, but i dont hink that i need half of the wiring that it has since i have started switching out my gauges from stock to Autometer Ultralite. I know that i need the wires for my ignition, but i think that that should be it right? Proably the wires for the blinkers and lights, and for my cooling fan relay.

Thanks

Anthony
Click to expand...


Like this?

I wired my car all by hand using a painless wiring race car panel. What you can do is take the computer harness and pull out each wire one by one. I did that before I went totally race car stripped. Had a ton of wires out of the bay. Then move things around as you wish. Not really that hard. Keep track of what you do, step by step and dont forget to test each step. Take the fender liners out and run the wiring there. Have one or two pieces of split tubing going to the engine to make the final connections and viola'.

Id start on a long weekend and have another vehicle available to buy parts. I suggest heat shrink and solder if you can solder. If not a good crimper and good terminals. The home depot terminals are better than the autozone ones IMO.

I'd go ahead and move that battery to the trunk with a box and 3/8 hold downs as a minimum.

Tools, crimpers, diagonal cutters (snips), test light and a multi meter or a continuity tester. Meter will cost you about $15-20 at walmart or pep boys and comes in real handy. Learn to use the continuity and voltage sections and you are good.
 

marine_2003

Member
Jun 6, 2005
427
0
16
Lake County, FL
Oct 8, 2005
#3
  • Oct 8, 2005
  • #3
Just Like that, what do i need to do to get it like that?
 

hllon4whls

BANNED
Founding Member
Jan 17, 2002
2,567
0
46
Covington
Oct 8, 2005
#4
  • Oct 8, 2005
  • #4
I updated my last post please reread.

I should have used at least satin instead of flat paint, however it still came out well IMO. Did it with rattle cans and the engine still in the bay.

I ran most of the brake lines custom. The fronts are still stock, but the back is run down the passenger side and are all new.
 

marine_2003

Member
Jun 6, 2005
427
0
16
Lake County, FL
Oct 8, 2005
#5
  • Oct 8, 2005
  • #5
When i go to do this, should i leave the motor in or take it out? Also, since i am not using the stock gauges anymore should i take out the computer? Also, Take apart or tear down the dash? What are the terminals you are talking about?
 

hllon4whls

BANNED
Founding Member
Jan 17, 2002
2,567
0
46
Covington
Oct 9, 2005
#6
  • Oct 9, 2005
  • #6
marine_2003 said:
When i go to do this, should i leave the motor in or take it out? Also, since i am not using the stock gauges anymore should i take out the computer? Also, Take apart or tear down the dash? What are the terminals you are talking about?
Click to expand...


It will be easier to take out the engine if you are going to paint. For the wiring, it is not necessary.

For the dash, you dont need to take it out to get the computer wiring out. The computer is under the pass kick panel. Trace out the wires and cut them out one by one to be safe. Going to take a while to do that, esp if you do it by yourself. To me it is the best way. Your gauges are not controlled by the computer.

Again, the trick is taking your time.

For the computer wiring, you will find that a bunch of the grounds are tied together. My car was a carbed, 351 hack job when I got it so I had to clean it up. Surprised it did not catch on fire with all of the wiring issues I resolved.
 

marine_2003

Member
Jun 6, 2005
427
0
16
Lake County, FL
Oct 9, 2005
#7
  • Oct 9, 2005
  • #7
Would I be able to buy a Switch Panel and take out all of my wiring and wire my headlights and cooling fan and gauge lights to the switch panel and use little stock wire as possibly? What does my computer control, sine the car is carburated? I have no radio and no interior so moving the battery isn going to be a problem. I am proably just going to spray paint the engine bay.
 

Killer50stang

New Member
May 11, 2004
632
0
0
Oct 9, 2005
#8
  • Oct 9, 2005
  • #8
hllon4whls said:
Like this?

I wired my car all by hand using a painless wiring race car panel. What you can do is take the computer harness and pull out each wire one by one. I did that before I went totally race car stripped. Had a ton of wires out of the bay. Then move things around as you wish. Not really that hard. Keep track of what you do, step by step and dont forget to test each step. Take the fender liners out and run the wiring there. Have one or two pieces of split tubing going to the engine to make the final connections and viola'.

Id start on a long weekend and have another vehicle available to buy parts. I suggest heat shrink and solder if you can solder. If not a good crimper and good terminals. The home depot terminals are better than the autozone ones IMO.

I'd go ahead and move that battery to the trunk with a box and 3/8 hold downs as a minimum.

Tools, crimpers, diagonal cutters (snips), test light and a multi meter or a continuity tester. Meter will cost you about $15-20 at walmart or pep boys and comes in real handy. Learn to use the continuity and voltage sections and you are good.
Click to expand...

What kind of jimmy rigged pulley setup is this?
 

hllon4whls

BANNED
Founding Member
Jan 17, 2002
2,567
0
46
Covington
Oct 9, 2005
#9
  • Oct 9, 2005
  • #9
Killer50stang said:
What kind of jimmy rigged pulley setup is this?
Click to expand...

One that cost me 8 bucks and works fine through 6800 rpm runs. The WP is a moroso kit. About $80 vs $300 for full on electric. The other bracket is a chrome alt bracket commonly sold at auto zone. Some off the shelf belt from NAPA and voila' race car with an alternator.

Had I thought about the way a 66 mustang alternator mounts to the block, I may have used that setup. I did not fully realize how it mounted until after I completed mine.

Works fine, lasts long time. Wont rust, bust, or collect dust.
 

hllon4whls

BANNED
Founding Member
Jan 17, 2002
2,567
0
46
Covington
Oct 9, 2005
#10
  • Oct 9, 2005
  • #10
marine_2003 said:
Would I be able to buy a Switch Panel and take out all of my wiring and wire my headlights and cooling fan and gauge lights to the switch panel and use little stock wire as possibly? What does my computer control, sine the car is carburated? I have no radio and no interior so moving the battery isn going to be a problem. I am proably just going to spray paint the engine bay.
Click to expand...


The computer does nothing since the car is carbed. The only thing that I would check is that your fuel pump works even if the computer is not plugged up. Possibly they went with a manual version or a key on hot with a relay or the stock relay.

The painless switch panel will do headlights and ignition, but IMO for a streetable car, it is better to stay with the factory wiring. Clean it with some gojo and a rag, cut to the proper length and route it out of site.

Turn signals, high beams, horn, reverse lights, etc are a pain to wire up. Might as well leave the factory stuff in there if it works. The exception is all of the puter wiring that is just looking sloppy under the hood. Remember, all I have is wp, fp, fans, tailight, pw, dome light, ignition, starter, line loc and tail light circuits in my car. Nothing else.



Keep track of how much wire comes out of just that computer harness.
 

dirtysohc

Founding Member
Aug 7, 2002
103
0
0
High Point N.C.
Oct 14, 2005
#11
  • Oct 14, 2005
  • #11
Run all the wires under the fenders and hide them anywhere you can. It's a long job but rewarding. Not a good pic but here's what mine looks like.

 

dirtysohc

Founding Member
Aug 7, 2002
103
0
0
High Point N.C.
Oct 14, 2005
#12
  • Oct 14, 2005
  • #12
Sorry, I'm still learning how to post pics and stuff here. This one you can see better.

 

Attachments

  • davidscar65pn.webp
    2.8 KB · Views: 129

DMAN302

My mom says thanks for the pearl necklace.
Nov 8, 2003
2,120
2
59
windsor, Canada
Oct 14, 2005
#13
  • Oct 14, 2005
  • #13
Very very nice...clean and looks slick.
 

pb_paulie_b

Founding Member
May 19, 2001
894
0
0
Chaptico, Maryland
Oct 14, 2005
#14
  • Oct 14, 2005
  • #14
do it like this www.cardomain.com/ride/2146037/2 in in the middle of doin mine right now...PB
 

dirtysohc

Founding Member
Aug 7, 2002
103
0
0
High Point N.C.
Oct 14, 2005
#15
  • Oct 14, 2005
  • #15
Thanks DMAN! Yea Paulie I've done the cardomain thing but for some reason when you "expand" the pics now they don't get any bigger than what they are ont the page, at least for me they don't. Here's my page with my '96 and '83. I haven't updated in over a year though. Your car looks very nice Paulie!

http://www.cardomain.com/ride/229400
 

pb_paulie_b

Founding Member
May 19, 2001
894
0
0
Chaptico, Maryland
Oct 14, 2005
#16
  • Oct 14, 2005
  • #16
dirtysohc said:
Thanks DMAN! Yea Paulie I've done the cardomain thing but for some reason when you "expand" the pics now they don't get any bigger than what they are ont the page, at least for me they don't. Here's my page with my '96 and '83. I haven't updated in over a year though. Your car looks very nice Paulie!

http://www.cardomain.com/ride/229400
Click to expand...
thanks dirty, i likes the white car! i couldn't get your pix to expand either?..PB
 
You must log in or register to reply here.

Similar threads

T
Electrical Brown Connector #31
  • ta66
  • Jul 26, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
218
Fox 5.0 Mustang Tech Jul 30, 2026
ta66
T
Resolved Wiring electric fan
  • cbac89
  • Aug 29, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
3
Views
234
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 30, 2026
cbac89
Electrical Ron Francis Headlight / Alternator Harness
  • dan50
  • Apr 30, 2026
  • Fox 5.0 Mustang Tech
Replies
0
Views
330
Fox 5.0 Mustang Tech Apr 30, 2026
dan50
Resolved 93 Mustang 5.0 - Cranks but does not start
  • dan50
  • Jul 18, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
480
Fox 5.0 Mustang Tech Jul 18, 2026
dan50
Resolved Holley terminator integration into CCRM
  • BrandonMP
  • Feb 25, 2026
  • SN95 4.6L Mustang Tech
Replies
8
Views
601
SN95 4.6L Mustang Tech Aug 23, 2026
fasterthangas
F
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?