• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech

Engine code p0118

  • Thread starter Thread starter Black GT
  • Start date Start date Mar 24, 2020
B

Black GT

Active Member
Sep 8, 2018
148
9
28
Jacksonville, Florida
Mar 24, 2020
#1
  • Mar 24, 2020
  • #1
Yesterday while driving my 01 GT I noticed something just didn't feel right. While sitting in line at taco belle the engine idle would on its on raise up from 700 to 1100 rpm's. Then it would drop back down to around 500. Car is a manual. This morning I was driving the car and it was doing the same thing. While sitting at a red light at a busy intersection the idle started rising slightly and the the engine shut off. It took about 30 seconds of cranking before it started. It normally starts right up. When I got home I grabbed my scan tool to check the code. P0118 Engine coolant temperature circuit high input. I checked it in live data mode and noticed my coolant temperature would rise to 208 degrees before the cooling fans would come on and then would drop to 199 degrees before the fans went off. My temperature gauge reads normal at the half way mark. Aren't these temperature a good bit above normal? A few minutes later I started the car and it blew out a cloud of blue smoke. Several hours later I started the car to move it to my driveway and there was no smoke at all. I have noticed the last couple of months that while sitting idling for several minutes when the engine reads max operating temperature (half way on gauge} the car emits blue smoke out the exhaust. It while driving the car never emits smoke only idling when the engine is hot. Any input is appreciated. Wanted to add, the freeze frame data from when the code was set says the ECT reading was -40.
 
Last edited: Mar 24, 2020

wmburns

SN Certified Technician
Aug 14, 2009
5,892
514
204
Houston Texas
Mar 25, 2020
#2
  • Mar 25, 2020
  • #2
Black GT said:
Wanted to add, the freeze frame data from when the code was set says the ECT reading was -40.
Click to expand...
^^^This is the expected results when there's a problem with the PCM receiving a valid ECT sensor signal. This is also what the P0118 DTC is trying to tell you.

Since the ECT value is valid sometimes and not others, this tells me that the ECT sensor itself is likely OK. I would look for a wiring problem between the ECT sensor and the PCM. Think corrosion or poor connector pin fitment.

One way to trouble shoot this is with a "wiggle" test. IE, wiggle the wiring harness while monitoring the ECT value looking for a change.

Black GT said:
I checked it in live data mode and noticed my coolant temperature would rise to 208 degrees before the cooling fans would come on and then would drop to 199 degrees before the fans went off. My temperature gauge reads normal at the half way mark. Aren't these temperature a good bit above normal?
Click to expand...
For the record the above ECT temperature are NOT high. But if you are concerned double check that the engine cooling fan is actually works on BOTH speeds.
 
Last edited: Mar 25, 2020
Reactions: Black GT
B

Black GT

Active Member
Sep 8, 2018
148
9
28
Jacksonville, Florida
Mar 25, 2020
#3
  • Mar 25, 2020
  • #3
Thanks wmburns. I will check the wiring today and see if I can find the problem.
 
B

Black GT

Active Member
Sep 8, 2018
148
9
28
Jacksonville, Florida
Mar 26, 2020
#4
  • Mar 26, 2020
  • #4
Is this the ECT sensor?
 

Attachments

  • IMG_1376.webp
    165.4 KB · Views: 1,049

wmburns

SN Certified Technician
Aug 14, 2009
5,892
514
204
Houston Texas
Mar 27, 2020
#5
  • Mar 27, 2020
  • #5
Yes that is the ECT sensor in the first intake runner (coolant cross over).
 
Last edited: Mar 27, 2020
Reactions: Black GT
You must log in or register to reply here.

Similar threads

D
1996 gt mustang block temp vs coolant temp
  • Dkuehn
  • May 21, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
1
Views
37
1996 - 2004 SN95 Mustang -General/Talk- May 22, 2026
squeak93
J
High idle 2003 Mach 1
  • JohnnyUtah
  • Mar 29, 2026
  • SN95 4.6L Mustang Tech
Replies
3
Views
124
SN95 4.6L Mustang Tech Mar 31, 2026
JohnnyUtah
J
K
Engine 2000 Mustang GT - Fuel issue post-blown spark plug repair
  • kenster1092
  • Feb 26, 2026
  • SN95 4.6L Mustang Tech
Replies
4
Views
283
SN95 4.6L Mustang Tech Mar 10, 2026
kenster1092
K
P
Repeated P2004 DTC trouble code with no apparent symptoms
  • poehitman
  • Mar 11, 2026
  • SN95 V6 Mustang Tech
Replies
2
Views
156
SN95 V6 Mustang Tech Mar 12, 2026
poehitman
P
P
2000 GT Random Power Loss
  • Pinellas50
  • Mar 9, 2026
  • SN95 4.6L Mustang Tech
Replies
4
Views
230
SN95 4.6L Mustang Tech Mar 23, 2026
Pinellas50
P
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?