• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Engine Removal (1992 5.0)

  • Thread starter Thread starter DonMaximo
  • Start date Start date Aug 19, 2007
D

DonMaximo

Member
Sep 25, 2003
217
5
19
Lewisville, Texas
Aug 19, 2007
#1
  • Aug 19, 2007
  • #1
First off... this is a phenominal website. I can't believe the wealth of information and photos people share here.

I want to remove engine and all components from engine bay to prep for a color change. Engine & exhaust will be completely replaced.

I don't need a tremendous amount of detail, but help with some tips would be appreciated. I'm prepared to take pictures, labeling. and packaging of Hardware/etc. in zip lock bags. Any input on order, gotchas, tricks, etc would be greatly appreciated.

-D
 

juiced_94gt

Active Member
Mar 30, 2005
1,143
0
36
Southern California
Aug 19, 2007
#2
  • Aug 19, 2007
  • #2
you can remove the engine and tranny as one to make less work for you, just jack up the car after you disconnect the driveshaft and all the wiring and stuff under the hood, if your leaving the tranny in the car you can still just take all the 6 bolts from the bellhousing off and the tranny can stay in the car...this is my 94

 

Attachments

  • Picture189.webp
    91.1 KB · Views: 1,709

NKau

Founding Member
Dec 15, 2001
1,346
0
37
Jefferson, WI
Aug 19, 2007
#3
  • Aug 19, 2007
  • #3
What he said. I always remove the engine with the tranny attached, even if I only want to pull the engine. Removing the radiator and accessories made the job a lot easier in terms of pulling and reinstalling the engine/tranny for me. It takes literally 5 minutes with the help of a friend to get the engine/tranny back into or out of the car as an assembly. A good trick is to jack the rear of the car up high on jackstands when you are ready to pull them or reinstall them together. You'll see what I mean after you do this

The zip-lock bag method of cataloging hardware is a good one. Saves a lot of time when you are reassembling v.s. sifting through a bucket of bolts.
 
S

stalkercobra89

New Member
Jun 19, 2005
30
0
0
Aug 20, 2007
#4
  • Aug 20, 2007
  • #4
yea a hate to admit this one but i just did this recently and unless you drain the trans be sure to block off the shifter hole, speedo hole and the tail shaft. i used the end of a driveshaft i cut off. as long as you do that i would definately do it in one piece. also a bolt in opposite corners of the motor in the header bolt holes turned out to be a pretty good move when we pulled it. didn't even need a leveler! and you can leave the whole intake assymbled good luck to ya.
 

Flavadave4

Active Member
Nov 28, 2003
1,044
21
49
Utica, NY
Aug 20, 2007
#5
  • Aug 20, 2007
  • #5
Lable everything if your unsure, thats the best way to elliminate problems later.


Welcome aboard!
 

SVT32VDOHC

waiting for the next hack atta
Founding Member
Nov 22, 2001
3,501
28
119
Motor City
Aug 20, 2007
#6
  • Aug 20, 2007
  • #6
It is pretty straight forward. The only thing I can think of that can get people is ground straps. I tend to forget about those things, and when you forget to hook them back up and the car won't start....rrrggrrrrrr. Just look for them on the firwall, and the core support and you will be good.
 
D

DonMaximo

Member
Sep 25, 2003
217
5
19
Lewisville, Texas
Aug 27, 2007
#7
  • Aug 27, 2007
  • #7
Engine Removal - for engine compartment Paint

Guys... this info has been very helpful.

I should add that I need to completely gut the engine compartment because we're changing the color of the car.

We're putting stupid money into this rebuild/upgrade...so we need to do it right. Just looking for help here to simply things or get it right the first time.

Once again... many thanks again for your input.
 

302RollinHard

New Member
Sep 26, 2005
0
0
0
Columbus, OH
Aug 27, 2007
#8
  • Aug 27, 2007
  • #8
I label both sides of each electrical connection I disconnect with duct tape and a number written with a sharpie, then all you have to do is match numbers when you put it back together. After a couple of times, you don't have to do this anymore as it is second nature. Also motor and tranny at the same time is very nice.
 

pwcracer

Founding Member
Jun 13, 2000
347
0
16
Hastings, MN, USA
Aug 27, 2007
#9
  • Aug 27, 2007
  • #9
I just removed the engine on my 94 as well.. THe starter was a pita to get at with headers, and the only other thing I ran into was about 4 quarts of trans fluid from the transmission dumped out..
 
You must log in or register to reply here.

Similar threads

Engine Engine and Transmission Removal Tips
  • Justin87
  • Apr 5, 2019
  • Fox 5.0 Mustang Tech
Replies
6
Views
2K
Fox 5.0 Mustang Tech Apr 27, 2019
Justin87
Timing Cover/harmonic Balancer Removal And Replacement
  • jrichker
  • May 28, 2017
  • Fox 5.0 Mustang Tech
Replies
1
Views
16K
Fox 5.0 Mustang Tech Jul 6, 2024
Noobz347
First restoration
  • Tllindsey
  • Apr 14, 2013
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
6
Views
685
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Apr 16, 2013
91TwighlightGT
  • Locked
1992 LX 5.0 hatchback
  • alanw6
  • Oct 17, 2009
  • Fox Body Mustangs For Sale (1979-93)
  • 2
Replies
36
Views
34K
Fox Body Mustangs For Sale (1979-93) Feb 2, 2011
karagannis112
K
W
-Classic-Fit Big Pony Polo shopping online
  • wvowor09
  • Mar 15, 2011
  • Regional Forums and Event Information
Replies
0
Views
2K
Regional Forums and Event Information Mar 15, 2011
wvowor09
W
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?