• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Exhaust hitting control arm....help!

  • Thread starter Thread starter jmd2914
  • Start date Start date Feb 6, 2006
J

jmd2914

Founding Member
Sep 6, 2002
937
0
0
Napa, California
Feb 6, 2006
#1
  • Feb 6, 2006
  • #1
alright, on the drivers side back where my exhaust goes up over the axle the pipe is hitting against the control arm when i drive. and its really starting to bug me not to mention sound really bad when i drive. im about ready to just cut of my tails and weld on turndowns unless anyone has any suggestions. if so please tell me.
 
S

ss93cobra

Founding Member
Apr 10, 2002
1,422
1
0
Wilmington NC
Feb 6, 2006
#2
  • Feb 6, 2006
  • #2
Did you recently install a cat back system? If so, loosen it right behind the muffler, rotate the tailpipe a little, and tighten it down. Check to make sure that the muffler is parallel with the ground too...
 

Euphoric306

New Member
Apr 5, 2004
905
0
0
Feb 6, 2006
#3
  • Feb 6, 2006
  • #3
if you've got any type of aftermarket mufflers, my vote is for teh turndowns


other than that, check your exhaust hangers, there's one mounted with the tranny on the crossmember, one on each muffler, and one on each tailpipe. if one or more of those are not connected, the tension in the connections will flex the entire system, my right tailpipe was rubbing on my tire for a while
 
J

jmd2914

Founding Member
Sep 6, 2002
937
0
0
Napa, California
Feb 6, 2006
#4
  • Feb 6, 2006
  • #4
i bought a flowmaster american thunder catback but i yanked them out and had race bullets welded in, so i cant rotate the pipe. so im thinkin i might just put dumps on, however im not sure how its gonna look cuz the body kit had holes for tailpipes in the back. anyone have any suggestions?
 

larrendeuce

Member
Sep 13, 2003
649
1
19
Southern NJ
Feb 6, 2006
#5
  • Feb 6, 2006
  • #5
Try loosening it at the midpipe to flowtube flange, depending on where your muffler hangers were put it might give you enough wiggle room.
 
S

ss93cobra

Founding Member
Apr 10, 2002
1,422
1
0
Wilmington NC
Feb 7, 2006
#6
  • Feb 7, 2006
  • #6
Or worst case, have an exhaust shop cut it, rotate the tailpipe, and weld it back together. As far as dumps go
 
You must log in or register to reply here.

Similar threads

R
Exhaust Exhaust smell in cabin
  • Rcdgl
  • Oct 16, 2024
  • Fox 5.0 Mustang Tech
Replies
15
Views
1K
Fox 5.0 Mustang Tech Oct 20, 2024
nickyb
new :poo: box, may need to hit you guys up for 79-82 info when i fix thIs turd.
  • rednotch
  • Sep 27, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2 3
Replies
44
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 23, 2026
limp
2
Resolved Electrical mayhem
  • 2000ElectricGreen
  • Mar 13, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
3
Views
495
1996 - 2004 SN95 Mustang -General/Talk- Sep 4, 2026
2000ElectricGreen
2
B
Where to go from here on my build…
  • B0udreaux
  • Jul 14, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
8
Views
467
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jul 18, 2026
AeroCoupe
Drivetrain 83’ Glx convertible C5 Trans help!
  • JacksonJared2113
  • Dec 25, 2025
  • Fox 5.0 Mustang Tech
Replies
2
Views
542
Fox 5.0 Mustang Tech Dec 26, 2025
JacksonJared2113
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?