• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-

Got the car dynoed and tuned

  • Thread starter Thread starter 04GTMustang
  • Start date Start date Jan 22, 2010

04GTMustang

New Member
Feb 28, 2006
348
0
0
Stafford
Jan 22, 2010
#1
  • Jan 22, 2010
  • #1
Alright guys im back again been very busy. I finally got the car dyno tuned after getting twin gt 500 fuel pumps and a cobra tank installed.

it made 412rwhp and 427rwtq on the 9psi pulley. would have tuned it on 11psi but the tuner was afraid to blow the car up being that its stock motor lol. he was tuning it at first on 11psi but when he realized it spiked 13.5lbs of boost and held to redline he let out of it at 3500 and it was making 450rwhp so he was afraid to go any further hahahaha. dunno why the 11psi pulley was boosting this hard but i was laughing when right when he stabbed it i saw 11psi and then by 3500 it was hitting 13.5. oh well would have been nice to see what it would have made at redline if he finished tuning it on that boost.

ill post up graphs later cause im sitting in the computer lab on campus

EDIT: and why i had twin pumps installed was one i got the whole setup from a guy for 600 dollars and it was too good to pass up and 2 because the fuel pump maxed at 4000rpms with the boost a pump
 

myponyrocks

I have more billet on the Stang than most women ha
Apr 18, 2004
1,219
0
37
Jan 22, 2010
#2
  • Jan 22, 2010
  • #2
Where's your boost gauge hooked to? Shouldn't be getting that high of boost off of that pulley, maybe your gauge is wrong as well? The rest of your pulleys are stock right?
 

04GTMustang

New Member
Feb 28, 2006
348
0
0
Stafford
Jan 22, 2010
#3
  • Jan 22, 2010
  • #3
myponyrocks said:
Where's your boost gauge hooked to? Shouldn't be getting that high of boost off of that pulley, maybe your gauge is wrong as well? The rest of your pulleys are stock right?
Click to expand...

its not my gauge i dont have a boost gauge yet lol it was the tuners gauge thats connected to all his tuning software and crap.

and yes the rest of my pulleys are stock. granted it was 25 degrees too during tuning
 

BurningRubber

10 Year Member
Dec 6, 2004
1,865
24
58
Jan 23, 2010
#4
  • Jan 23, 2010
  • #4
Sick man, but we all know your engine will never blow, lol.

It's been through hell and back and just laughs in the face of power.
 

04GTMustang

New Member
Feb 28, 2006
348
0
0
Stafford
Jan 23, 2010
#5
  • Jan 23, 2010
  • #5
Hahaha if only the tuner knew that lol 92000 miles on her and running like a champ. I was nervous on the dyno cause I didn't want a
boom but I wanna see what 11 psi had
 

deftsound

Please ask me how much my supercharger cost
Apr 6, 2004
945
1
39
Texas City TX
Jan 23, 2010
#6
  • Jan 23, 2010
  • #6
Nice numbers man! Now put some LT headers on there!
 

04GTMustang

New Member
Feb 28, 2006
348
0
0
Stafford
Jan 23, 2010
#7
  • Jan 23, 2010
  • #7
Ya it's on the to do list when I get the shortblock. Lol
 

deftsound

Please ask me how much my supercharger cost
Apr 6, 2004
945
1
39
Texas City TX
Jan 23, 2010
#8
  • Jan 23, 2010
  • #8
04GTMustang said:
Ya it's on the to do list when I get the shortblock. Lol
Click to expand...

yea you should see a nice 15-30rwhp gain with the lt's...not to mention the sound
 

04GTMustang

New Member
Feb 28, 2006
348
0
0
Stafford
Jan 26, 2010
#9
  • Jan 26, 2010
  • #9
my brother put some longtubes on his 07 and it sounds pretty nice. i dont think its as loud as my car in lower rpms but up top she screams pretty well. Ill probably get some when i get a new motor and put it all in at once instead of doing it twice.
 

Rickyll7

Member
Dec 16, 2005
718
4
19
Jan 26, 2010
#10
  • Jan 26, 2010
  • #10
In your sig you say you have a 3 inch pulley making 11 psi. Is the 3 inch pulley your "9 psi" pulley that made 412rwhp?

The "9 psi" pulley KB sent me is 3 1/8 inches in diameter.

What is the diameter of your "11 psi" pulley that made 13.5 psi?
 

04GTMustang

New Member
Feb 28, 2006
348
0
0
Stafford
Jan 26, 2010
#11
  • Jan 26, 2010
  • #11
Rickyll7 said:
In your sig you say you have a 3 inch pulley making 11 psi. Is the 3 inch pulley your "9 psi" pulley that made 412rwhp?

The "9 psi" pulley KB sent me is 3 1/8 inches in diameter.

What is the diameter of your "11 psi" pulley that made 13.5 psi?
Click to expand...

no the 3in is the 11psi pulley i was running that on a kenne bell tune then when i went to get a dyno tune they didnt wann tune it on that pulley so they put the stock 9psi pulley back in. i just havent updated my sig yet. the diameter of the 11in pulley that made 13.5 was 3 in lol thats why we have no clue why it was making that boost. could be a clogged cat or something.
 

Rickyll7

Member
Dec 16, 2005
718
4
19
Jan 26, 2010
#12
  • Jan 26, 2010
  • #12
so is your "9 psi" pulley 3 1/8 inches?

do you have any before and after dyno results from your meth kit?

was this a mustang dyno or dyno jet?

Nice numbers!
 

04GTMustang

New Member
Feb 28, 2006
348
0
0
Stafford
Jan 28, 2010
#13
  • Jan 28, 2010
  • #13
Rickyll7 said:
so is your "9 psi" pulley 3 1/8 inches?

do you have any before and after dyno results from your meth kit?

was this a mustang dyno or dyno jet?

Nice numbers!
Click to expand...

it was a dyno jet and i havent gotten it tuned with the meth yet. that dyno run there was with the meth unhooked cause i have a slight leak in one of the lines cause i ran 100% alcohol through it and i guess it ate some of the line at a connection haha. and yes my 9psi pulley is a 3 1/8in.

im pretty sure why its boosting so hard is because of somewhere in my exhaust system its clogged lol.
 

Rickyll7

Member
Dec 16, 2005
718
4
19
Jan 28, 2010
#14
  • Jan 28, 2010
  • #14
Remove the cats and your looking at another 10-20 rwhp depending on how clogged they are.
 

04GTMustang

New Member
Feb 28, 2006
348
0
0
Stafford
Jan 29, 2010
#15
  • Jan 29, 2010
  • #15
Rickyll7 said:
Remove the cats and your looking at another 10-20 rwhp depending on how clogged they are.
Click to expand...

im just waiting to get a motor and get longtubes and then im buying a new xpipe so i can do everything in one shot. i cant just take off my cats because I have emissions here.
 

Rickyll7

Member
Dec 16, 2005
718
4
19
Jan 29, 2010
#16
  • Jan 29, 2010
  • #16
04GTMustang said:
im just waiting to get a motor and get longtubes and then im buying a new xpipe so i can do everything in one shot. i cant just take off my cats because I have emissions here.
Click to expand...

Take it easy driving the car with clogged cats. Could cause some issues if sever enough and driven hard.
 
D

Drew0318

New Member
Aug 15, 2008
115
0
0
Chicago, IL
Jan 29, 2010
#17
  • Jan 29, 2010
  • #17
One benefit of living in a state/county with no emmisions regulations. No cats to clog up.
 
You must log in or register to reply here.

Similar threads

C
Boosted Boss 302 HP/TQ
  • coltoncaskey12
  • May 24, 2026
  • 2010 - 2014 Specific Tech
Replies
0
Views
88
2010 - 2014 Specific Tech May 24, 2026
coltoncaskey12
C
S
Fox '87 GT can't get to stay running
  • spilly
  • Mar 29, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
27
Views
763
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 20, 2026
spilly
S
For Sale 94 Cobra 408w AOD Project For Sale
  • Labora
  • Oct 11, 2024
  • SN95 Mustangs For Sale (1994-04)
Replies
1
Views
1K
SN95 Mustangs For Sale (1994-04) Apr 7, 2025
Labora
R
89' Stang - MS2PNP - Post tune - Surging issues
  • rushcanuck
  • May 8, 2020
  • Digital Self-tuning Forum
Replies
5
Views
2K
Digital Self-tuning Forum May 9, 2020
a91what
M
Electrical 95 cobra random dyno numbers
  • Moeofit32
  • Apr 14, 2020
  • 1994 - 1995 Specific Tech
Replies
8
Views
2K
1994 - 1995 Specific Tech Apr 19, 2020
Moeofit32
M
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?