• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

GT-40 vs Cobra intake

  • Thread starter Thread starter willys1
  • Start date Start date Jan 14, 2006
  • 1
  • 2
Next
1 of 2 Next Last

willys1

Active Member
Dec 2, 2003
1,004
1
36
New Jersey
Jan 14, 2006
#1
  • Jan 14, 2006
  • #1
I know they are very similar..But is the GT-40 really worth the extra money?
Are they identical in performance,or does one have an edge?
I know this is an old subject,but bare with me..
 

willys1

Active Member
Dec 2, 2003
1,004
1
36
New Jersey
Jan 14, 2006
#2
  • Jan 14, 2006
  • #2
bump
 

troyGT03

New Member
Feb 22, 2004
278
0
0
too close to memphis,tn
Jan 14, 2006
#3
  • Jan 14, 2006
  • #3
the tubular gt-40 is what i have now. i have had both. the intakes flow almost identical or very close(within a few cfm). old question that pops up here almost weekly. basically it is a money/cosmetic decision to me. what looks best to you and what you want to spend.
 

willys1

Active Member
Dec 2, 2003
1,004
1
36
New Jersey
Jan 14, 2006
#4
  • Jan 14, 2006
  • #4
troyGT03 said:
the tubular gt-40 is what i have now. i have had both. the intakes flow almost identical or very close(within a few cfm). old question that pops up here almost weekly. basically it is a money/cosmetic decision to me. what looks best to you and what you want to spend.
Click to expand...
I wanna spend the least amount of money but want GT-40 perfrmance!!
Till this day every comparisin I read,even with the new BBK manifold,with the stock cam you just "cant" beat its all around performance.Its great for low end torque and doesnt quit till 5500 rpm But they never seem to come down in price so pretty much there the same? I hope 25thmustang stops in I know he has a Cobra.
 

Mavrick

Founding Member
Aug 29, 2002
2,264
0
46
Collingwood, ON
Jan 14, 2006
#5
  • Jan 14, 2006
  • #5
They flow equally... they share the same lower manifold, which is the bottle neck to begin with.
 

willys1

Active Member
Dec 2, 2003
1,004
1
36
New Jersey
Jan 14, 2006
#6
  • Jan 14, 2006
  • #6
Mavrick said:
They flow equally... they share the same lower manifold, which is the bottle neck to begin with.
Click to expand...
bottle neck for which,the stock lower rite?
 

Mavrick

Founding Member
Aug 29, 2002
2,264
0
46
Collingwood, ON
Jan 14, 2006
#7
  • Jan 14, 2006
  • #7
Both the Cobra and the GT40 intakes share the GT40 lower intake. Both upper's flow more CFM than their matching lowers, therefore the lowers are still the bottle neck of both intakes.

With a ported lower, maybe the GT40 would outflow the Cobra.. that i don't know.
 

willys1

Active Member
Dec 2, 2003
1,004
1
36
New Jersey
Jan 14, 2006
#8
  • Jan 14, 2006
  • #8
Mavrick said:
Both the Cobra and the GT40 intakes share the GT40 lower intake. Both upper's flow more CFM than their matching lowers, therefore the lowers are still the bottle neck of both intakes.

With a ported lower, maybe the GT40 would outflow the Cobra.. that i don't know.
Click to expand...
Does the Cobra use an EGR spacer?
 

troyGT03

New Member
Feb 22, 2004
278
0
0
too close to memphis,tn
Jan 14, 2006
#9
  • Jan 14, 2006
  • #9
yes the cobra and the tubular upper both use a egr spacer
 
M

Marlboro_Man

Member
Sep 30, 2005
437
1
18
Houston, TX
Jan 15, 2006
#10
  • Jan 15, 2006
  • #10
troyGT03 said:
yes the cobra and the tubular upper both use a egr spacer
Click to expand...
My cobra doesn't use a spacer , it's built into the upper intake. So no spacer here.
 

carbed87

Member
Jun 5, 2005
215
0
16
Jan 15, 2006
#11
  • Jan 15, 2006
  • #11
gt-40 all teh way!
 

timewarped1972

Member
Jun 17, 2004
642
0
16
mesa, az
Jan 15, 2006
#12
  • Jan 15, 2006
  • #12
yeah it's funny how they supposedly flow about the same but when ever you see a magazine shoot out or something they always use the gt-40 and not the cobra.....i'm sure there's been dyno tests done if one knew where to find the results...

i made my mind up when i do get to that point i'll probably get a cobra, they seem to be on a wide range of cars that are way faster than anything i'll ever build so i'm sure it will be good enough for me, and you rarely see anyone complaining of it being too big or losing low end torque on stock headed engines. plus i guess if you change your mind down the road you can always just buy the gt 40 upper, or buy the whole thing and sell the new lower with the old upper to recoup some of the money spent..can't beat the 350 bucks or so for the cobra vs the almost 600 for the gt-40.....

and yes they have egr provision built in, don't need to buy a seperate spacer, so you save another 40 bucks or what ever a spacer costs on top.......
 

Maryland Stang

Active Member
Aug 21, 2002
1,656
30
39
Greenville, NC
Jan 15, 2006
#13
  • Jan 15, 2006
  • #13
timewarped1972 said:
i guess if you change your mind down the road you can always just buy the gt 40 upper, or buy the whole thing and sell the new lower with the old upper to recoup some of the money spent..can't beat the 350 bucks or so for the cobra vs the almost 600 for the gt-40.....
Click to expand...

Much like a real Cobra intake Ford seems to have sold all of the GT-40 intakes. I don't see them making them in China either. The GT-40 was a hand assembled intake and after looking at some of the horrible work the Chinese are doing on the new Cobra I don't see them making the GT-40.

If you're on a budget the Ford Explorer is the way to go. It shares the same basic lower as the Cobra and GT-40 but uses a cast version of the GT-40 upper. There are two versions of the Explorer, one has EGR and the other doesn't. You can usually pick them up off of Ebay for around $200.
 

Rick 91GT

Mustang Master
Nov 29, 1999
9,692
95
99
PA
Jan 15, 2006
#14
  • Jan 15, 2006
  • #14
The GT-40 Upper comes a restriction after awhile, that is where the Cobra in better IMO. To work over a GT40 Upper you need to cut it up to port it, straighten out the inlet area etc.

The lowers are the same and can be ported, the Cobra is the only upper that truly can be worked over easily. The Cobra uses a internal EGR (no spacer), the Gt40 requires a spacer.

There are better manifolds out then those two as well even with a worked stock head, technology is wonderful....
 

Michael Yount

Mustang Master
Apr 10, 2002
9,039
6
79
Charlotte, NC
Jan 15, 2006
#15
  • Jan 15, 2006
  • #15
....although, from a number of recent mag tests -- if the engine you're building is like the vast majority of mildly modded 5.0's on the street you won't do a lot better performance-wise than the GT40 family of intakes. In all the tests I've seen on 302 cubic inch engines with mild mods (peak power at or below about 5700 rpm) they not only hold their own against the competitors, they usually produce the best low/mid rpm numbers, and the best average numbers.

The only benefit of the GT40 over the other 2 is 1) it weighs about 8 lbs. less, and 2) appearance (which is subjective). For a very modest amount, tmoss can port the lower which takes flow numbers for these intakes from the 200-210 range up into the 250 range.

Rick will set you up with something that's gonna see higher-rpm race duty -- and need to perform/flow at higher rpm. But for milder mods, street friendly revs (idle to 5500) and superior bottom end/midrange numbers -- it's really hard to beat the GT40 trio, especially when you factor in cost. I'm sure Rick would agree - it's all about assembling an ENTIRE combo that's aimed at a particular user's need. And more often than not, putting something together that's gonna be a better compromise for street and strip requires different components than a race-only engine.
 

timewarped1972

Member
Jun 17, 2004
642
0
16
mesa, az
Jan 15, 2006
#16
  • Jan 15, 2006
  • #16
ok is there an explorer intake that is a direct bolt on?? i know like mentioned earlier there's one of the explorer year intakes that needs some modifying which is kinda why i was thinking more the cobra route.......so there is a certain year explorer that needs no modding to just swap on for 87 to 93 5.0's??
 

Michael Yount

Mustang Master
Apr 10, 2002
9,039
6
79
Charlotte, NC
Jan 15, 2006
#17
  • Jan 15, 2006
  • #17
...the closest to meeting that criteria will be the early model Exp's -- 96/early 97. However, even they will not have the hole for the ACT sensor in the number 5 runner. You'll either need to drill/tap for it; or alter your wiring harness and relocate the ACT sensor. I did the latter -- it was a very easy change to move it to the elbow just upstream of throttle body. I believe you'll also need to make provisions for the coolant return from the egr spacer - another drill/tap job.
 

willys1

Active Member
Dec 2, 2003
1,004
1
36
New Jersey
Jan 15, 2006
#18
  • Jan 15, 2006
  • #18
Michael Yount said:
....although, from a number of recent mag tests -- if the engine you're building is like the vast majority of mildly modded 5.0's on the street you won't do a lot better performance-wise than the GT40 family of intakes. In all the tests I've seen on 302 cubic inch engines with mild mods (peak power at or below about 5700 rpm) they not only hold their own against the competitors, they usually produce the best low/mid rpm numbers, and the best average numbers.

The only benefit of the GT40 over the other 2 is 1) it weighs about 8 lbs. less, and 2) appearance (which is subjective). For a very modest amount, tmoss can port the lower which takes flow numbers for these intakes from the 200-210 range up into the 250 range.

Rick will set you up with something that's gonna see higher-rpm race duty -- and need to perform/flow at higher rpm. But for milder mods, street friendly revs (idle to 5500) and superior bottom end/midrange numbers -- it's really hard to beat the GT40 trio, especially when you factor in cost. I'm sure Rick would agree - it's all about assembling an ENTIRE combo that's aimed at a particular user's need. And more often than not, putting something together that's gonna be a better compromise for street and strip requires different components than a race-only engine.
Click to expand...
No-No!!,,I still got the same stock motor in my LX! With the exception of Thumpers!
OK,being the EGR is built in to the Cobra will the TB still physically come out to the same postion where it is now? Im using a power pipe that is really tight, so I need the TB at the same exact lacation where it is now!!
 

Rick 91GT

Mustang Master
Nov 29, 1999
9,692
95
99
PA
Jan 15, 2006
#19
  • Jan 15, 2006
  • #19
willys1 said:
No-No!!,,I still got the same stock motor in my LX! With the exception of Thumpers!
OK,being the EGR is built in to the Cobra will the TB still physically come out to the same postion where it is now? Im using a power pipe that is really tight, so I need the TB at the same exact lacation where it is now!!
Click to expand...


Yes the TB is still in the correct place, your stuff will swap right over.

I agree with what Micheal posted, it really is all in YOUR exact combo, you would benifit from a GT40 or Cobra manifold and depending on the cam you could use a TFS Street Heat or a Edelbrock Performer with really nice results. With the AOD you need to be really careful with the cam selection it will make and break a combo.

I still remember when we first built dads 93 Cobra, we sorked over the stock GT40 heads, Extrude honed the manifold, 2031 cam, full emissions and exhaust added a 83mm Pro-M, tuned it with the Speedbrain and ripped of 275RWHP and 12 sec ET's at the track. Even after we added the blower the car was the most street friendly combo's I have done to this day, drive like Grandma's sunday driver, until you blipped the throttle.

So what cam is in the car?
 

willys1

Active Member
Dec 2, 2003
1,004
1
36
New Jersey
Jan 15, 2006
#20
  • Jan 15, 2006
  • #20
Rick 91GT said:
Yes the TB is still in the correct place, your stuff will swap right over.

I agree with what Micheal posted, it really is all in YOUR exact combo, you would benifit from a GT40 or Cobra manifold and depending on the cam you could use a TFS Street Heat or a Edelbrock Performer with really nice results. With the AOD you need to be really careful with the cam selection it will make and break a combo.

I still remember when we first built dads 93 Cobra, we sorked over the stock GT40 heads, Extrude honed the manifold, 2031 cam, full emissions and exhaust added a 83mm Pro-M, tuned it with the Speedbrain and ripped of 275RWHP and 12 sec ET's at the track. Even after we added the blower the car was the most street friendly combo's I have done to this day, drive like Grandma's sunday driver, until you blipped the throttle.

So what cam is in the car?
Click to expand...
Stock cam with Thumper heads HD springs and 1.7 RR's.
 
  • 1
  • 2
Next
1 of 2 Next Last
You must log in or register to reply here.

Similar threads

N
Engine 86 GT no start/stall
  • nweber
  • Jul 28, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
278
Fox 5.0 Mustang Tech Jul 29, 2026
AeroCoupe
Fox Cobra wheels real vs. replicas
  • keel
  • Nov 3, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
13
Views
324
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Nov 11, 2026
keel
Cobra Brake Conversion - Spare Wheel/Tire Search
  • AeroCoupe
  • Aug 2, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
516
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 2, 2026
AeroCoupe
Resolved 1999 cobra removed lower intake manifold to crossovertube
  • hvcobra99
  • Sep 6, 2026
  • SVT Tech Forum
Replies
0
Views
167
SVT Tech Forum Sep 6, 2026
hvcobra99
First Car, what should I do for power??
  • tunedV6
  • Apr 13, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
7
Views
456
1996 - 2004 SN95 Mustang -General/Talk- May 4, 2026
580HP*428Cj
5
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?