• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-

Fox Gt40 Questions

  • Thread starter Thread starter 72gs455
  • Start date Start date Mar 2, 2018
7

72gs455

Member
Jun 16, 2017
28
5
13
Mar 2, 2018
#1
  • Mar 2, 2018
  • #1
OK so i picked some gt40 heads without realizing they had 1/2 head bolt holes was told i could use some kind of reducer to bolt them on my 302 they also seem to have aftermarket springs now my questions is can i use my stock pushrod/cam? going to be using stock pedestal rockers until i get the budget to get pedestal mounted roller rockers also if there a way to id springs?
 

Attachments

  • IMG-1165.webp
    252.9 KB · Views: 238
  • IMG-1166.webp
    190 KB · Views: 211

Mstng93SSP

You have a nice rear end there Dave.
15 Year Member
Nov 29, 1999
2,993
3,500
184
Mililani, Hawaii
Mar 2, 2018
#2
  • Mar 2, 2018
  • #2
Yes, you need the bushings that step the head home down to 7/16. Here is a set of head studs with the bushings.

https://lmr.com/item/ARP-1544005/1979-95-Mustang-50L-Arp-High-Performance-Hex-Head-Stud-Kit
 
Reactions: 72gs455 and 90sickfox

90sickfox

Wasn't a pretty sight...and I've got big hands
SN Certified Technician
Mar 2, 2015
6,953
5,831
213
Mar 2, 2018
#3
  • Mar 2, 2018
  • #3
Or you can tap the block and use ARP studs for a 351.
 
7

72gs455

Member
Jun 16, 2017
28
5
13
Mar 2, 2018
#4
  • Mar 2, 2018
  • #4
Now what about the stock cam? Would I need to replace it?
 

Mstng93SSP

You have a nice rear end there Dave.
15 Year Member
Nov 29, 1999
2,993
3,500
184
Mililani, Hawaii
Mar 2, 2018
#5
  • Mar 2, 2018
  • #5
You can, but if in that deep already, get a good cam to go with the heads.
 

revhead347

Apparently my ex-husband made that mistake.
20+ Year Stangneter
Jun 14, 2004
9,303
1,649
214
Acworth, GA
Mar 4, 2018
#6
  • Mar 4, 2018
  • #6
72gs455 said:
OK so i picked some gt40 heads without realizing they had 1/2 head bolt holes was told i could use some kind of reducer to bolt them on my 302 they also seem to have aftermarket springs now my questions is can i use my stock pushrod/cam? going to be using stock pedestal rockers until i get the budget to get pedestal mounted roller rockers also if there a way to id springs?
Click to expand...

Are these GT40 heads or GT40P heads?

I've never used the reducers. That being said, it's the proper way to do it. Back when I started this, they either didn't make them, or no one had ever heard of them. I have always bolted heads right on with the standard ARP 7/16" stud or bolt kit and never had a problem.

Stock cam will work. It will make better power with a different cam. It's all a matter of how much time you want to spend vs cost/reward. Cams are cheap, but it's double the work to change the cam.

Stock rockers will work, but most people elect to go with rollers as it's not a huge cost or time consumer. Pushrods should be ok, but I would never send an engine without doing a pushrod geometry.

Based on what you are saying, I would save up the money for the rockers and possibly a cam before you do the swap. The incidental costs (like holy have you seen what a gallon of antifreeze goes for these days) of tearing down the engine twice exceeds the value of those parts.

Kurt
 
R

Rcdgl

5 Year Member
Feb 19, 2018
321
169
63
Mar 4, 2018
#7
  • Mar 4, 2018
  • #7
The washers for the 1/2 to 7/16 holes to bolts work fine. I used a set with the irongt40s on my 82 for ten years, took them off an reused them on the AFR heads. Also used stock bolt down rockers and pushrods. Worked fine to 6200 rpm many times.
 
7

72gs455

Member
Jun 16, 2017
28
5
13
Mar 5, 2018
#8
  • Mar 5, 2018
  • #8
revhead347 said:
Are these GT40 heads or GT40P heads?

I've never used the reducers. That being said, it's the proper way to do it. Back when I started this, they either didn't make them, or no one had ever heard of them. I have always bolted heads right on with the standard ARP 7/16" stud or bolt kit and never had a problem.

Stock cam will work. It will make better power with a different cam. It's all a matter of how much time you want to spend vs cost/reward. Cams are cheap, but it's double the work to change the cam.

Stock rockers will work, but most people elect to go with rollers as it's not a huge cost or time consumer. Pushrods should be ok, but I would never send an engine without doing a pushrod geometry.

Based on what you are saying, I would save up the money for the rockers and possibly a cam before you do the swap. The incidental costs (like holy have you seen what a gallon of antifreeze goes for these days) of tearing down the engine twice exceeds the value of those parts.

Kurt
Click to expand...
sorry works crazy so couldnt reply they are gt40s 3 bars
 

revhead347

Apparently my ex-husband made that mistake.
20+ Year Stangneter
Jun 14, 2004
9,303
1,649
214
Acworth, GA
Mar 5, 2018
#9
  • Mar 5, 2018
  • #9
72gs455 said:
sorry works crazy so couldnt reply they are gt40s 3 bars
Click to expand...

Don't worry, I don't go on this website for days at a time either. My buddy has a matching Cobra cam around here somewhere. Better than a GT cam anyway. We also have a set of GT40 Cobra heads here somewhere too. I think the cam is in the scrap steel barrel, that's how much I would recommend it over paying for a proper cam. But if you are nearby, you are welcome to it.

Kurt
 
You must log in or register to reply here.

Similar threads

H
1995 cobra engine noise help
  • Holt2010
  • Nov 8, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
0
Views
55
1996 - 2004 SN95 Mustang -General/Talk- Nov 8, 2026
Holt2010
H
P
Vacuum
  • ProTechAutoServices
  • Aug 1, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
13
Views
337
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 2, 2026
Noobz347
K
Engine Gt40p vs 180 procomp
  • Kleinjj27
  • Oct 27, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
477
Fox 5.0 Mustang Tech Nov 3, 2026
Kleinjj27
K
T
Oil burning on my recently buil 302
  • The blk67
  • May 15, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
247
Fox 5.0 Mustang Tech May 15, 2026
Noobz347
G
Sup. Just got back into the game with a 1986 4-eye vert.
  • GeorgeG
  • Nov 3, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
151
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Nov 7, 2026
limp
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?