• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Guage Cluster

  • Thread starter Thread starter Djstorm100
  • Start date Start date Jan 19, 2008
D

Djstorm100

Member
Aug 5, 2007
109
0
16
Jan 19, 2008
#1
  • Jan 19, 2008
  • #1
I hate to keep making post like this, but I dont want to messed something up and have to re do it. Plus its the only way to learn right? Other than messing up alot.

Point is I'm going to be putting autometer guages as my cluster. Now I was looking at people that made plates and ect for them. At the bottome I have picture of the all the wires. My question is What would be the best way to wire the guages up. At first I was thinking runing 12 guage wire and splice all the black in to one wire. Then run around 12 guage wire and splice all the white wirtes in to it. Would this be safe? I've wired up guages before just not this many all at once. I'm worried about load and getting the wire too hot. These are mech guages and I play to run Elec ones
 

xRacerX777x

New Member
Aug 20, 2007
2
0
0
Macedon, NY
Jan 20, 2008
#2
  • Jan 20, 2008
  • #2
I'd love to find out about this as well, the '86 Stang i have my eyes on could do with a makeover with the gauges...
 

LiquidGT

Member
Oct 8, 2007
368
0
16
Near STL hell
Jan 20, 2008
#3
  • Jan 20, 2008
  • #3
Are you just talking about the wires for the illumination bulbs in the gauges. If so, I think you have the right plan.
Do them all separate and it would be a rats nest.
 

bigcahoona

Member
Apr 11, 2005
74
0
6
Chi Town
Jan 20, 2008
#4
  • Jan 20, 2008
  • #4
I hooked them all together in the back with spade connectors then ran 1 and it was fine. I would not twist and tape because you don't want to keep taking it apart for a loose wires. Spade connect them.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Jan 20, 2008
#5
  • Jan 20, 2008
  • #5
The 12 gauge wire will carry 20 amps. The gauge illumination will only draw 2-4 amps at most. You should use an 18 gauge wire for the power and ground for the illumination circuit.

Using the 12 gauge wire for a ground won't hurt anything, but the wire is larger and will not bend easily to fit around the turns and curves.

I would use a separate 18 gauge wire to provide ground for the other gauge circuits.

Wire size current table for automotive use, total run lenght of less than 20 feet.
18 gauge wire = 5-8 amps
16 gauge wire = 10-12 amps
14 gauge wire = 15-17 amps
12 gauge wire = 20-25 amps
10 gauge wire = 30-40 amps
8 gauge wire = 50-60 amps.
 
D

Djstorm100

Member
Aug 5, 2007
109
0
16
Jan 20, 2008
#6
  • Jan 20, 2008
  • #6
bigcahoona said:
I hooked them all together in the back with spade connectors then ran 1 and it was fine. I would not twist and tape because you don't want to keep taking it apart for a loose wires. Spade connect them.
Click to expand...

jrichker said:
The 12 gauge wire will carry 20 amps. The gauge illumination will only draw 2-4 amps at most. You should use an 18 gauge wire for the power and ground for the illumination circuit.

Using the 12 gauge wire for a ground won't hurt anything, but the wire is larger and will not bend easily to fit around the turns and curves.

I would use a separate 18 gauge wire to provide ground for the other gauge circuits.

Wire size current table for automotive use, total run lenght of less than 20 feet.
18 gauge wire = 5-8 amps
16 gauge wire = 10-12 amps
14 gauge wire = 15-17 amps
12 gauge wire = 20-25 amps
10 gauge wire = 30-40 amps
8 gauge wire = 50-60 amps.
Click to expand...



so run 18-16 awg wire off each wire (black and white and Red (12volt switch). and then tie them in all together.

The way I was going to do it as take peiece of wire tab in to the 12 volt source (for the red wire) then every inch of so on that wire, take one of the guage wires and splice it in the 12volt wire.

Quick diagram I made for the 12 volt switch, The black and white wires would be hooked up in the same manner

View attachment 335672
 

86foureye

New Member
Mar 12, 2007
40
0
0
chandler
Jan 21, 2008
#7
  • Jan 21, 2008
  • #7
bigcahoona said:
I hooked them all together in the back with spade connectors then ran 1 and it was fine. I would not twist and tape because you don't want to keep taking it apart for a loose wires. Spade connect them.
Click to expand...

I would NOT use any connectors at all use soder and heat shrenk. converted my 86 to 87-93 dash soder and heat sheenk though the hole car that I wired.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Jan 21, 2008
#8
  • Jan 21, 2008
  • #8
What you are doing will work fine with 18 gauge wire. 86foreye's recommendation to use solder and heat shrink is the best method for all types of automotive electrical connections.
 
You must log in or register to reply here.

Similar threads

T
Electrical Brown Connector #31
  • ta66
  • Jul 26, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
219
Fox 5.0 Mustang Tech Jul 30, 2026
ta66
T
M
1996 GT Speedometer electrical nightmare
  • moon96gt
  • Oct 7, 2026
  • SN95 4.6L Mustang Tech
Replies
2
Views
189
SN95 4.6L Mustang Tech Oct 17, 2026
CAMTWO1070
Electrical Innovate PSB-1 is DOA? Am I an idiot? All plausable. Please Help
  • Dontknowchit
  • Apr 26, 2025
  • Fox 5.0 Mustang Tech
Replies
1
Views
685
Fox 5.0 Mustang Tech Apr 26, 2025
Dontknowchit
G
Hello and Instrument Wiring
  • GT Jon
  • Jul 5, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
3
Views
194
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jul 6, 2026
Mustang5L5
Forced Induction Bypass valve backwards?
  • Dontknowchit
  • Jun 25, 2025
  • Fox 5.0 Mustang Tech
Replies
3
Views
491
Fox 5.0 Mustang Tech Jun 29, 2025
JD1964
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?