• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech

Help! Driver seat is loose

  • Thread starter Thread starter serviator
  • Start date Start date Oct 15, 2004

serviator

Founding Member
Jun 12, 2001
182
0
16
Denmark (ex-resident of Colorado)
Oct 15, 2004
#1
  • Oct 15, 2004
  • #1
I started noticing the driver seat in my car being loose in turns. I can feel it move right under the butt, but the rest of the seat (back, sides) are firm.

I have tried pulling and pushing the seat from side to side on the rails, and it is not loose there, which makes me think it has something to do with a loose bolt in the power seat mechanics below.

Does anyone know if I have to repolster the seat to fix it, or how I can get the seat off and work my way in from underneath?

Any help appreciated!
:: Michael
 

john_324

New Member
Jan 14, 2003
446
1
0
Washington, D.C.
Oct 15, 2004
#2
  • Oct 15, 2004
  • #2
Subscribing. I seem to have the same issue.

It's not major, but I definitely hear/feel something move sometimes during hard cornering...
 

w00t

New Member
Mar 26, 2004
334
0
0
Arlington TX
Oct 15, 2004
#3
  • Oct 15, 2004
  • #3
Did you inspect all of the bolts holding the seat?
 

98stangv8

Active Member
Oct 3, 2003
1,036
0
36
fayetteville, nc
Oct 15, 2004
#4
  • Oct 15, 2004
  • #4
check all the bolts underneath..your seat may just be wearing out...I got my seats for under 300 for the set...and love them...hard as hell to put in, but def worth it


 

Attachments

  • seats.webp
    84.1 KB · Views: 372

serviator

Founding Member
Jun 12, 2001
182
0
16
Denmark (ex-resident of Colorado)
Oct 15, 2004
#5
  • Oct 15, 2004
  • #5
john_324> it only happened during hard cornering or high speeds a few month ago, now it happens at every little turn.

w00t> I didn't inspect all the bolts in the seat. I did take a look/feel below on the rails and everything I could get to was tight. I think the problem is further up in the seat and I am not sure how hard it is to get the seat off and if I get it off; can I even get into the powerseat mechanism to tighten anything? A mirror or a camera below would probably be a good idea, but I would still like insight from someone who knows about the powerseat structure.

98stangv8> I am pretty sure you are right about the loose bolt, as mentioned above - it's just getting to it. Your seats are nice, however I'd like to keep the ones I have now, so I am not quite ready to go that route .
 

w00t

New Member
Mar 26, 2004
334
0
0
Arlington TX
Oct 15, 2004
#6
  • Oct 15, 2004
  • #6
Sorry to hack. But 98stangv8, those are some clean arse seats! Are they comfortable as they look?
 

john_324

New Member
Jan 14, 2003
446
1
0
Washington, D.C.
Oct 15, 2004
#7
  • Oct 15, 2004
  • #7
serviator said:
john_324> it only happened during hard cornering or high speeds a few month ago, now it happens at every little turn.
Click to expand...

Uh oh. So you mean if I ignore this problem, it isn't going to go away???
 

serviator

Founding Member
Jun 12, 2001
182
0
16
Denmark (ex-resident of Colorado)
Oct 15, 2004
#8
  • Oct 15, 2004
  • #8
john_324 said:
Uh oh. So you mean if I ignore this problem, it isn't going to go away???
Click to expand...

Nope, it's only going to get worse, so find a solution before it is too late and share it with me .

On a more serious note, I will probably see if I can get under the seat this weekend and figure out how hard it is to take apart. Just wish someone had a diagram or could give me a direction of how to disassemble it (eg. number of bolts, positioning). .
 

w00t

New Member
Mar 26, 2004
334
0
0
Arlington TX
Oct 16, 2004
#9
  • Oct 16, 2004
  • #9
serviator said:
Nope, it's only going to get worse, so find a solution before it is too late and share it with me .

On a more serious note, I will probably see if I can get under the seat this weekend and figure out how hard it is to take apart. Just wish someone had a diagram or could give me a direction of how to disassemble it (eg. number of bolts, positioning). .
Click to expand...

Go to Autozone and pickup one of those Haynes manuals. They have a complete teardown/rebuild w/ pics for around 8 bucks. Great to have as a reference.
 

serviator

Founding Member
Jun 12, 2001
182
0
16
Denmark (ex-resident of Colorado)
Oct 16, 2004
#10
  • Oct 16, 2004
  • #10
I got hold of the Mustang Service Manual, and it helped me get the seat out without a problem. I tried troubleshooting the components for quite a while, but still no luck after assembling it again.

If you look at the first attached picture, it shows the bottom of the seat. The framed green area shows the entire piece that I was able to slightly move back and fourth. It seemed to me like the "bolt's" hole (framed with red) is a little bigger than the "pole/screw" part thereby causing the movability.

The yellow arrows shows the screws and bolts I tightened and the next picture shows the "bolt" in close up.

After reassembling it, the seat was still loose and the powerseat engine had a harder time moving the seat, probably because I tightened something I shouldn't have.

When I test drove it on a deserted street, I swerved left and right and felt with my right hand behind the seat. It seemed like the rail attached to the floor was firm, but the rail attached to the seat was moving away from the floor rail.

Would the "bolt" I am referring to as a possibly problem cause this behaviour or should I work on another part of the seat?



 

serviator

Founding Member
Jun 12, 2001
182
0
16
Denmark (ex-resident of Colorado)
Oct 19, 2004
#11
  • Oct 19, 2004
  • #11
Bumping in hope someone may be able to help.
 

holler

Founding Member
Dec 5, 2000
332
0
0
Chicago
Oct 19, 2004
#12
  • Oct 19, 2004
  • #12
suscribing, there is a little play in my seat too, that I find annoying.
 

masterchief2003

New Member
Nov 17, 2003
51
0
0
motor city!!!!!!!!!!
Oct 19, 2004
#13
  • Oct 19, 2004
  • #13
mine does the same thing from time to time
 

lgndracer

New Member
Feb 21, 2004
393
0
0
Sumner, WA
Oct 19, 2004
#14
  • Oct 19, 2004
  • #14
Same thing here. I had the dealership look at it, and they said everything was solid that they could tighten. Doesn't seem to get worse, but can definitly feel it over bump, and hard into corners.
 
F

ForPointSex

Founding Member
Mar 19, 2002
395
0
16
Mercer, NJ
Oct 19, 2004
#15
  • Oct 19, 2004
  • #15
My car does the same thing. I couldn't figure it out either, so I'm living with it.
 

serviator

Founding Member
Jun 12, 2001
182
0
16
Denmark (ex-resident of Colorado)
Oct 21, 2004
#16
  • Oct 21, 2004
  • #16
FYI - I send an email with the picture to a friend/mechanic, and ofcourse hard as it is troubleshooting looking at a picture, he couldn't tell for sure, but he thought it was the "bolt" I have framed in red and included a close up of.

I am going to order a new part, install it and get back here to let you know if that was the culpret.

lgndracer> When my car was under warranty I only felt it in the situations you describe and the dealership gave me the same story. I suggest you print out the pictures I submitted and ask them to check the part on your car.
 
You must log in or register to reply here.

Similar threads

E
2003 Mustang GT convertible water leak
  • Eightiesrock1980
  • Jul 27, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
4
Views
111
1996 - 2004 SN95 Mustang -General/Talk- Jul 28, 2026
Noobz347
L
2012 Seats in 98 GT Convertible - pictures coming
  • lparsons42
  • Aug 11, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
3
Views
277
1996 - 2004 SN95 Mustang -General/Talk- Aug 17, 2025
lparsons42
L
Cooling Jacket Pitting Idea's?
  • BoostedRed89gt
  • Sunday at 8:31 AM
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
10
Views
100
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sunday at 8:13 PM
Blackhawkxx
S
Help me solve a seat belt connector mystery
  • SciMan
  • Jun 25, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
1
Views
224
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 27, 2025
Noobz347
T
Fox Convertible top issues
  • TDM389
  • Feb 15, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
5
Views
321
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Feb 15, 2026
General karthief
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?