Hood pins

f8tlfiveo · Nov 21, 2012

I was throwing around the idea of putting hood pins on my car.. At 100 mph it seems to bounce around more than I like. Anyone have any good experiences with a good brand? I don't want it to look cheesy, but I don't really trust the stock latch with a fiberglass hood.

ratio411 · Nov 21, 2012

We have the Ford Performance (SVO, FMS, whatever Ford is calling their aftermarket parts division this week.)
They are about a month old, and are supposed to be stainless steel.
I think the pins themselves are stainless, but the clips and trim rings are already rusty.

These are on my teen son's car, and my 87 has a set by a previous owner (badly rusted too), but I'd never put pins on my personal car by my own choice.

I have used a lanyard cable before that was bolted to the hood latch support, then when the hood was shut, it would hang down and I would clip or padlock the other end of the lanyard to the lower radiator support. This gives some theft protection and holds the hood down.

My opinion... your's may vary.

Bullitt347 · Nov 21, 2012

http://www.aerocatch.com/ I have these on my 89 Saleen and they look great and work awesome. I personally like the flush mount and you never have to worry about rust/corrosion making them look bad. Are they cheap........uh, no. But you do get what you pay for.

atey950 · Nov 21, 2012

I will find where I bought mine. They are 8 years old and no rust. I put them on for the same reason...didn't trust that the latch with the fiberglass hood. I kept picturing it on the road in my rearview mirror

Sharad · Nov 22, 2012

f8tlfiveo said:
I was throwing around the idea of putting hood pins on my car.. At 100 mph it seems to bounce around more than I like. Anyone have any good experiences with a good brand? I don't want it to look cheesy, but I don't really trust the stock latch with a fiberglass hood.

I'm not allowed to make a brand recommendation since I'm a forum sponsor, but I can tell you that I once bought a Fox and a couple days after I bought it, the hood flew up on the highway. (It had an aftermarket hood, which I didn't personally install) It was a terrifying experience at highway speeds!

srtthis · Nov 22, 2012

f8tlfiveo said:
I was throwing around the idea of putting hood pins on my car.. At 100 mph it seems to bounce around more than I like. Anyone have any good experiences with a good brand? I don't want it to look cheesy, but I don't really trust the stock latch with a fiberglass hood.

i have spectra stainless ones on my car with the stock hood. i also didnt trust the stock latch it always seemed to bounce around a lot.

89stang1 · Nov 23, 2012

i got tired of rolling the dice too my hood popped a couple times in the last couple years held only by the safety latch scary ! so i got UPR shelby polished hoodpins im happy as hell with them. I never wanted hoodpins on my car now i wouldnt have any other way hood dont move at any speed and ive grown to love the look.

f8tlfiveo · Nov 23, 2012

89stang1 said:
i got tired of rolling the dice too my hood popped a couple times in the last couple years held only by the safety latch scary ****! so i got UPR shelby polished hoodpins im happy as hell with them. I never wanted hoodpins on my car now i wouldnt have any other way hood dont move at any speed and ive grown to love the look.

They look good. I'm not sure what I want to do but I don't want my hood coming unlatched..

RacEoHolic330 · Nov 23, 2012

Ever consider those flush-mount aerocatch latches? A bit different. If you have a dark colored car, they will be barely noticable.

f8tlfiveo · Nov 23, 2012

Someone has given that suggestion.. I looked at them and like them but not sure it's what I want on my car

Bryan83taco · Nov 23, 2012

Can somebody post a pic of how the pin attaches to the radiator support bracket? I have a set of pins laying around that I need to install.

srtthis · Nov 23, 2012

Bryan83taco said:
Can somebody post a pic of how the pin attaches to the radiator support bracket? I have a set of pins laying around that I need to install.

gimme a few minutes ill go get a picture of mine...

srtthis · Nov 23, 2012

cant see it but there is a nut top and bottom of the core support

89stang1 · Nov 23, 2012

mikestang63 · Nov 23, 2012

IMO you MUST have some sort of hood pins if you have any fiberglass hood. I dont care what brand it is. I have seen and read too many stories of hoods flying up at high speed. My own personal experience was with a Cervini ram air hood on my 87 S trimmed convertible that made about 400 hp. I was messing around one day showing off and hit the gas hard , and the hood came flying up. I hit the brake hard and luckily it only damaged the cowl and the back portion of the hood. Turns out the latch portion tore right off the hood. Maybe mine was just a bad hood as Cervini makes a quality piece. Not blaming them but thanks to my $5000 custom pearl paint job it was almost a grand to repaint the cowl and hood. Scared the living crap out of me. The NEXT DAY I put a set of hood pins on, and since that is the first thing I install on every one of my cars with a fiberglass hood. Live and learn.

Blkngold · Nov 23, 2012

Bullitt347 said:
http://www.aerocatch.com/ I have these on my 89 Saleen and they look great and work awesome. I personally like the flush mount and you never have to worry about rust/corrosion making them look bad. Are they cheap........uh, no. But you do get what you pay for.

Can you post pics of the Saleen hood with those flush pins?

Sent from my PC36100 using Tapatalk 2

mikestang63 · Nov 23, 2012

These are simply wicked looking and I may get these for my next hood

http://www.themustangnews.com/content/2010/02/quik-latch-solves-mustang-hood-pin-woes/

Bryan83taco · Nov 24, 2012

Thanks for the pics guys. It looks like you used the hood bumper holes.

srtthis · Nov 24, 2012

correct....

89stang1 · Nov 24, 2012

srtthis said:
correct....

yes

Hood pins

My wife likes my spool and blow-off valve.

I have been doing it wrong this whole time

ALWAYS choose the V over the P!!! Wait... what?

the guy doing it does every local racers rear end

Stroked and Juiced

Attachments

My wife likes my spool and blow-off valve.

Attachments

I like to dress like a pretty girl

My wife likes my spool and blow-off valve.

Active Member

the guy doing it does every local racers rear end

the guy doing it does every local racers rear end

Attachments

Stroked and Juiced

Attachments

New Member

Attachments

Active Member

the guy doing it does every local racers rear end

Stroked and Juiced

Similar threads

Privacy & Transparency

Privacy & Transparency